Rockwell Automation Allen-Bradley PanelView 5310 User manual

PanelView 5310 Terminals
Catalog Numbers 2713P-T6CD1, 2713P-T6CD1-B, 2713P-T6CD1-K,
2713P-T7WD1, 2713P-T7WD1-B, 2713P-T7WD1-K, 2713P-T9WD1,
2713P-T9WD1-B, 2713P-T9WD1-K, 2713P-T10CD1, 2713P-T10CD1-B,
2713P-T10CD1-K, 2713P-T12WD1, 2713P-T12WD1-B, 2713P-T12WD1-K
User Manual Original Instructions

2Rockwell Automation Publication 2713P-UM001G-EN-P - May 2022
PanelView 5310 Terminals User Manual
Important User Information
Read this document and the documents listed in the additional resources section about installation, configuration, and
operation of this equipment before you install, configure, operate, or maintain this product. Users are required to familiarize
themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws, and standards.
Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to
be carried out by suitably trained personnel in accordance with applicable code of practice.
If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be
impaired.
In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the use
or application of this equipment.
The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and
requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for
actual use based on the examples and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software
described in this manual.
Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc., is
prohibited.
Throughout this manual, when necessary, we use notes to make you aware of safety considerations.
Labels may also be on or inside the equipment to provide specific precautions.
WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous environment,
which may lead to personal injury or death, property damage, or economic loss.
ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property
damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the consequence.
IMPORTANT Identifies information that is critical for successful application and understanding of the product.
SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous
voltage may be present.
BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that surfaces may
reach dangerous temperatures.
ARC FLASH HAZARD: Labels may be on or inside the equipment, for example, a motor control center, to alert people to
potential Arc Flash. Arc Flash will cause severe injury or death. Wear proper Personal Protective Equipment (PPE). Follow ALL
Regulatory requirements for safe work practices and for Personal Protective Equipment (PPE).

Rockwell Automation Publication 2713P-UM001G-EN-P - May 2022 3
Table of Contents
Preface
Summary of Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Request Corresponding Source for Open Source Packages . . . . . . . . . 8
Product Firmware and Release Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Additional Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Chapter 1
Overview About the PanelView 5310 Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Hardware Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Operator Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Touch Gestures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Studio 5000 Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
EtherNet/IP Communication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Typical Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Catalog Number Explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Product Selections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Ethernet Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Chapter 2
Install the PanelView 5310
Terminal
Installation Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Environment and Enclosure Information. . . . . . . . . . . . . . . . . . . . 20
Wiring and Safety Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Outdoor Installation Recommendations . . . . . . . . . . . . . . . . . . . . 21
Mounting Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Mounting Clearances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Panel Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Panel Cutout Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Terminal Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Prepare for Panel Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Mount the Terminal in a Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Remove and Replace Power Terminal Block . . . . . . . . . . . . . . . . . . . . . 32
Connect Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Connect to a Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Ethernet Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Linear Network Topology. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Star Network Topology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Initial Startup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Update the Firmware before You Use the Terminal . . . . . . . . . . 37
Chapter 3
Configure Terminal Settings Runtime Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Enter Data With Virtual Keyboards . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Specify Keypad or Keyboard Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Log On to the Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

4Rockwell Automation Publication 2713P-UM001G-EN-P - May 2022
Table of Contents
Log Off of the Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Settings Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Configure the IP Address of the Terminal. . . . . . . . . . . . . . . . . . . . . . . 48
Use DHCP to Assign an IP Address for the Terminal . . . . . . . . 48
Assign a Static IP Address for the Terminal . . . . . . . . . . . . . . . . . . 49
Configure a DNS Address for the Terminal . . . . . . . . . . . . . . . . . . . . . 50
Configure the Ethernet Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
View the Network Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Use the Data Export Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Adjust the Brightness of the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Modify Screen Color Settings By Using HMI Device Tags. . . . . . . . 55
Configure the Display Screen Saver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Calibrate the Touch Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Disable Downloads to the Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Change the HMI Device Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
View the Firmware Revision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Display Terminal Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Enable the VNC Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Load an Application from Removable Media . . . . . . . . . . . . . . . . . . . . 64
Reboot the Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Change the Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
View Information for the Configured Controller . . . . . . . . . . . . . . . . 67
Manage Certificates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Import a Digital Certificate from Removable Media . . . . . . . . . . 69
Delete a digital certificate from the HMI Device . . . . . . . . . . . . . 70
Chapter 4
Monitor and Manage Control
System Alarms
Alarm Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Alarm Help Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
View the Alarm Summary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Manage the Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Alarm Detail Pane Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Filter the Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
View the Alarm History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Export the Alarm History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
View Automatic Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Chapter 5
Install and Replace
Components
Accessories and Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Voltage Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Electrostatic Discharge Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Connect to USB Ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
USB Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Insert an SD Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Replace the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Rockwell Automation Publication 2713P-UM001G-EN-P - May 2022 5
Table of Contents
Chapter 6
Update Firmware Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Get the Terminal Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Install the ControlFLASH Plus Software. . . . . . . . . . . . . . . . . . . . . . . . 94
Update the Firmware by Using ControlFLASH Plus Software . . . . 94
Verify the Firmware Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Chapter 7
Troubleshooting Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Troubleshooting Profiles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Import a Troubleshooting Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Export a Troubleshooting Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Terminal Does Not Start Up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Terminal Restarts Intermittently . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Touch Screen Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Display Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Ethernet Issues. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Cannot Download Application to Terminal. . . . . . . . . . . . . . . . . . . . 105
Performance Is Slow. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Resistance to Chemicals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Clean the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Remove Paint and Grease . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Equipment Wash Downs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Ship the Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Restore Factory Defaults. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Dispose of the Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Index
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

6Rockwell Automation Publication 2713P-UM001G-EN-P - May 2022
Table of Contents
Notes:

Rockwell Automation Publication 2713P-UM001G-EN-P - May 2022 7
Preface
This manual describes how to install, configure, operate, and troubleshoot the
PanelView™ 5310 terminals. This manual does not provide procedures on how to
create applications that run on the terminals, or ladder logic that runs in the
controller.
Other tasks that you must do include:
• Configure the Ethernet settings and update the firmware of the terminal.
• Create a project by using the Studio 5000 View Designer® application.
• Create control logic for the controller by using the Studio 5000 Logix
Designer® application.
Summary of Changes This manual contains new and updated information as indicated in the following
table.
Package Contents The PanelView 5310 terminals ship with these items.
IMPORTANT You must configure the Ethernet settings and update the firmware
before you can download a View Designer project and use the
terminal. See Initial Startup on page 37.
Topic Page
Added a new graphic that depicts acceptable and unacceptable mounting positions. 23
Item Description
Hardware • Mounting levers for panel installation
• Removable DC power terminal block
Documents • PanelView 5310 Terminals Product Information, publication 2713P-PC001
• Cutout Templates for PanelView 5310 Terminals, publication 2713P-DS001

8Rockwell Automation Publication 2713P-UM001G-EN-P - May 2022
Preface
Request Corresponding
Source for Open Source
Packages
The software included in this product contains copyrighted software that is
licensed under one or more open source licenses. Copies of those licenses are
included with the software. Corresponding Source for open source packages
included in this product can be found at the websites identified in the product
documentation.
You may alternately obtain complete Corresponding Source by contacting
Rockwell Automation via our Contact form on the Rockwell Automation
website: http://www.rockwellautomation.com/global/about-us/contact/
contact.page. Please include ‘Open Source’ as part of the request text.
Product Firmware and
Release Notes
Product firmware and release notes are available online at the Product
Compatibility and Download Center at
https://compatibility.rockwellautomation.com/Pages/home.aspx.
1. On the PCDC home page, search for your product.
2. On the search results page, find the firmware and release notes for your
product.
See the Product Compatibility and Download Center Quick Start Guide,
publication PCDC-QS001, for instructions on how to find and download
firmware and release notes for the terminal.
IMPORTANT Do not modify the DMK file. The DMK file is used in firmware updates and a
modified DMK file can cause the firmware update to fail.

Rockwell Automation Publication 2713P-UM001G-EN-P - May 2022 9
Preface
Additional Resources These documents contain additional information about related products from
Rockwell Automation.
You can view or download publications at
http://www.rockwellautomation.com/global/literature-library/overview.page.
Resource Description
PanelView 5310 Terminals Specifications
Technical Data, publication
2713P-TD001
Provides specifications and certifications for the PanelView 5310 terminal.
Industrial Automation Wiring and
Grounding Guidelines, publication
1770-4.1
Provides general guidelines for installing a Rockwell Automation industrial
system.
Guidelines for Handling Lithium Batter-
ies Technical Data, publication AG-5.4 Provides guidelines to store, handle, install, and dispose of lithium batter-
ies.
Safety Guidelines for the Application,
Installation, and Maintenance of
solid-state Controls, publication SGI-1.1
Provides general guidelines for the application, installation, and mainte-
nance of solid-state equipment.
Product Certifications website,
rok.auto/certifications Provides declarations of conformity, certificates, and other certification details.

10 Rockwell Automation Publication 2713P-UM001G-EN-P - May 2022
Preface
Notes:

Rockwell Automation Publication 2713P-UM001G-EN-P - May 2022 11
Chapter 1
Overview
About the PanelView 5310
Terminals
The PanelView™ 5310 terminals are operator interface devices that monitor and
control devices attached to ControlLogix® 5570 or 5580 controllers or
CompactLogix™ 5370, 5380, or 5480 controllers over an EtherNet/IP™ network.
Animated graphic and text displays provide operators with a view into the
operating state of a machine or process. Operators interact with the control
system by using the touch screen.
The PanelView 5310 terminals include these features and capabilities:
• Tightly integrated control and design environment allows information to
be shared between the PanelView 5310 terminal and the Logix platforms.
• The Studio 5000® environment provides one point of access for the Studio
5000 View Designer® and Studio 5000 Logix Designer® applications.(1)
• Connection to one ControlLogix 5570 or 5580 controller or one
CompactLogix 5370, 5380, or 5480 controller with revision 27 firmware
or later.
• Supports a maximum of 100 user-defined screens.
• Supports a maximum of 4,000 Logix-based alarms.(1)
• Easily configured screen navigation menu.
• Automatic Diagnostics capability.
• Conformal coating available for all terminal sizes.
Topic Page Topic Page
About the PanelView 5310 Terminals 11 EtherNet/IP Communication 15
Hardware Features 12 Typical Configuration 15
Operator Control 13 Catalog Number Explanation 16
Touch Gestures 13 Product Selections 16
Studio 5000 Environment 14 Accessories 16
(1) PanelView 5310 firmware can support up to 4,000 Logix-based alarms in one controller if you use Studio 5000 View Designer
application version 5 and Studio 5000 Logix Designer application version 32 or higher. Of the 4,000 alarms, no more than 1,000 can
be instruction-based. Earlier versions of the Studio 5000 View Designer or Studio 5000 Logix Designer applications can support up
to 1,000 Logix-based alarms.

12 Rockwell Automation Publication 2713P-UM001G-EN-P - May 2022
Chapter 1
Hardware Features The PanelView 5310 terminal features fixed-hardware configurations in a range
of display sizes with touch screen input.
2
3
4
7
1
24
7
56
356
4
8
Table 1 - Hardware Features
Item Feature Description
1 Display/Touch screen TFT color, SVGA, VGA, WVGA, or WXGA graphic display with a touch screen available in sizes of 5.7-in., 7-in., 9-in., 10.4-in., and 12.1-in.
2 Power 24V DC nom (18…30V DC) non-isolated power input
3 Ethernet port One 10/100Base-T, Auto MDI/MDI-X, EtherNet/IP port for controller communication.
4 Mounting slots Mounting levers insert into the slots to mount device in a panel or enclosure. The number of slots varies by terminal size.
5 Universal serial bus (USB)
host port One USB 2.0 high-speed (type A) host port.
6 USB device port One USB 2.0 high-speed (type B) device port to connect a host computer that is software-feature dependent.
7 SD card slot One slot that supports an SD™ or SDHC™ card that is recommended in Table 5 on page 17.
8 Status Indicators STS indicator (green) indicates that the terminal is on and in use.
ERR indicator (red) indicates hardware and firmware faults.

Rockwell Automation Publication 2713P-UM001G-EN-P - May 2022 13
Chapter 1
Operator Control All PanelView 5310 terminals have a color display with a touch screen for
operator control. The resistive touch screen provides accurate, durable touch
control for industrial applications.
Touch Gestures The PanelView 5310 terminal supports touch gestures to interact with screen
elements during runtime. Standard touch gestures include:
•Tap – Briefly touch the target on the HMI display with your fingertip.
•Drag – Move your fingertip over the target on the HMI display without
contact loss.
For a list of actions you can perform by using touch gestures, see the View
Designer help.
ATTENTION: The touch screen accepts input from a finger, stylus, or gloved
hand for operation in dry or wet environments.
The plastic stylus must have a minimum tip RADIUS of 1.3 mm (0.051 in.).
Any other object or tool can damage the touch screen.
ATTENTION: Do not perform multiple operations simultaneously. Multiple
simultaneous operations can result in unintended operation.
Touch only one operating element on the screen with one finger at a time.
TIP During runtime, a virtual keyboard or numeric keypad opens on HMI displays
for data entry.

14 Rockwell Automation Publication 2713P-UM001G-EN-P - May 2022
Chapter 1
Studio 5000 Environment Use the Studio 5000 environment to create HMI applications for the PanelView
5310 terminal.
The Studio 5000 environment includes these applications:
•View Designer – you can create and design a project for a specific
PanelView 5310 terminal and download the project to the terminal.
You can create an application for any PanelView 5310 terminal and reuse
that same application across the entire platform.
•Logix Designer application – you can develop control logic for a
CompactLogix or ControlLogix controller and download the logic to the
controller.
Figure 1 - How Studio 5000 Applications Work Together
LINK NET OK
1
2
3
4
5
7
6
8
View Designer
Application
Logix Designer
Application
Tag Browser
Offline
ACD File
HMI Project
(VPD File)
HMI Device Controller
Runtime
Communication

Rockwell Automation Publication 2713P-UM001G-EN-P - May 2022 15
Chapter 1
Tab l e 2 describes how the View Designer and Logix Designer applications work
together to create an HMI runtime project.
EtherNet/IP
Communication
The PanelView 5310 terminals contain EtherNet/IP technology. These
terminals communicate with ControlLogix or CompactLogix controllers over an
Ethernet connection with linear network topologies. Star technology is also
supported when using switches.
Typical Configuration Linear and star network topologies are supported. See these topics for examples:
•Linear Network Topology on page 36
•Star Network Topology on page 36
Table 2 - Studio 5000 Applications and Tools
Item Component Description
1View Designer
application
A Studio 5000 application that is used to build HMI projects.
Studio 5000 View Designer projects are stored as VPD files that can be downloaded to the
PanelView 5310 terminal.
2 Tag browser A tool that is used to search for and select tags within a Studio 5000 Logix Designer
application ACD project file. You can bind the tags to graphic element properties and
properties of an HMI display. The Studio 5000 View Designer application uses the tag
browser to read data from an ACD file.
3Logix Designer
application A Studio 5000 application that is used to develop control logic for an industrial automation system. The Studio 5000 Logix Designer application interfaces with
controllers to read and write tag information. Studio 5000 Logix Designer application
projects are stored as ACD files that can be downloaded to the controller.
4 ACD file An Automation Controller Database (ACD) file. An ACD file is a Logix Designer application
project file that contains the logic or code, including tags and data types, which runs
within a controller.
5 HMI project
(VPD file)
A View Project Database (VPD) file. A VPD project is a file that contains the operator
interface application, including HMI displays, controller references, and information
about the HMI device to run the application.
6 HMI device A Human Machine Interface (HMI) device, such as the PanelView 5310 terminal, which
runs the HMI project. At runtime, the HMI device communicates directly with the
controller.
7 Runtime The environment in which the runtime HMI project communicates with the controller.
During runtime, the HMI device runs the downloaded project, exchanges data with the
controller, animates displayed data, and responds to operator input.
8 Controller A logic controller such as a ControlLogix or CompactLogix controller.

16 Rockwell Automation Publication 2713P-UM001G-EN-P - May 2022
Chapter 1
Catalog Number
Explanation
This table provides an explanation of the catalog numbers.
Product Selections This table provides information for the product selections.
Accessories Tab le 3 through Ta ble 7 list accessories for the PanelView 5310 terminals.
Bulletin Input Type Display Size Display Type Power Ethernet Port – Special Option
|| | || ||
2713P- T = Touch 6 = 5.7-in. C = Color, 4:3 aspect ratio D = DC 1 = Single – B = Without brand identity(2)
7 = 7-in. W = Color, widescreen(1) aspect ratio K = Conformal coating(3)
9 = 9-in.
10 = 10.4-in.
12 = 12.1-in.
(1) Depending on the PanelView 5310 terminal model, the widescreen aspect ratio is either 5:3 or 16:10. For further details, see the Product Selections section on this page.
(2) A catalog number with -B at its end (for example, 2713P-T9WD1-B) is a terminal without the Allen-Bradley logo and product identification on the front bezel.
(3) A catalog number with -K at its end (for example, 2713P-T6CD1-K) is a terminal with conformal coating.
Cat. No. Display
Input
Power
Ethernet
Port
Memory
Touch Screen Display Size Type
Aspect
Ratio
Pixels
(W x H) RAM User (1)
2713P-T6CD1
2713P-T6CD1-B
2713P-T6CD1-K
5.7-in. VGA
TFT color 4:3 640 x 480 DC One 1 GB 1 GB
2713P-T7WD1
2713P-T7WD1-B
2713P-T7WD1-K
7-in. WVGA
TFT color 5:3 800 x 480
2713P-T9WD1
2713P-T9WD1-B
2713P-T9WD1-K
9-in.
2713P-T10CD1
2713P-T10CD1-B
2713P-T10CD1-K
10.4-in. SVGA
TFT color 4:3 800 x 600
2713P-T12WD1
2713P-T12WD1-B
2713P-T12WD1-K
12.1-in. WXGA
TFT color 16:10 1280 x 800
(1) Nonvolatile memory that is available to store projects.
Table 3 - Power Supplies and Power Terminal Blocks
Cat. No. Description Quantity
1606-XLB120E DIN rail power supply, 24…28V DC output voltage, 120 W 1
1606-XLP100E DIN rail power supply, 24…28V DC output voltage, 100 W 1
1606-XLP95E DIN rail power supply, 24…28V DC output voltage, 95 W 1
2711-TBDC 3-pin DC power terminal block 10

Rockwell Automation Publication 2713P-UM001G-EN-P - May 2022 17
Chapter 1
SD™ and SDHC™ accessory cards in Tab le 5 have been designed to meet
industrial robustness and environmental requirements. Rockwell Automation
recommends that you use these accessory cards with the terminal to help reduce
the chances of corruption. Studio 5000 View Designer software requires the
following for SD cards that are inserted into the HMI device:
• 4 GB of free space if the project uses data logging
• A supported SDHC card type, preferably one listed in Table 5
• An environmental rating for the PanelView 5310 environment
• A supported format of either FAT32 or ext3
Ethernet Cables See the Industrial Ethernet Media Brochure, publication 1585-BR001, for
recommended Ethernet cables and media solutions.
See the USB to Serial Adapter Quick Start Guide, publication GMSC10-QS003,
for information on USB to serial port adapters.
Table 4 - Mounting Hardware
Cat. No. Description Quantity
2711P-RMCP(1) Mounting levers (black) 16
(1) Use catalog number 2711P-RMCP mounting levers (black) for PanelView 5310 terminals. Do not use gray mounting levers; they
are not compatible with PanelView 5310 terminals.
Table 5 - Secure Digital (SD) Cards (1)
Cat. No. Description Quantity
1784-SDHC8 8-GB SDHC card 1
1784-SDHC32 32-GB SDHC card 1
(1) To help reduce the chance of corruption when you use SD Cards or USB drives with the terminal, Rockwell Automation
recommends that you use only the above SD card catalog numbers.
Table 6 - USB Programming Cable
Cat. No. Description Length
6189V-USBCBL2 Programming cable that connects the device port of the terminal to a USB
host port of a computer. 1.8 m (5.9 ft)
Table 7 - Protective Overlays
Cat. No.(1)
(1) Although these protective overlays were designed for the PanelView 5510 terminals, they can also be used for the PanelView 5310
terminals. However, when these overlays are used on a PanelView 5310 terminal, there is an increased air gap between the overlay
and the terminal screen.
Display Size Quantity
2711P-RGT6S 6-in.
3
2711P-RGT7SP 7-in. widescreen
2711P-RGT9SP 9-in. widescreen
2711P-RGT10SP 10.4-in.
2711P-RGT12SP 12.1-in. widescreen

18 Rockwell Automation Publication 2713P-UM001G-EN-P - May 2022
Chapter 1
Notes:

Rockwell Automation Publication 2713P-UM001G-EN-P - May 2022 19
Chapter 2
Install the PanelView 5310 Terminal
Topic Page
Installation Precautions 20
Mounting Considerations 23
Mounting Clearances 23
Panel Guidelines 24
Panel Cutout Dimensions 24
Terminal Dimensions 25
Prepare for Panel Mounting 26
Mount the Terminal in a Panel 29
Remove and Replace Power Terminal Block 32
Connect Power 33
Connect to a Network 34
Initial Startup 37
ATTENTION: Do not use a PanelView™ 5310 terminal for emergency stops or
other controls critical to the safety of personnel or equipment. Use separate
hard-wired operator interface devices that do not depend on solid-state
electronics.

20 Rockwell Automation Publication 2713P-UM001G-EN-P - May 2022
Chapter 2
Installation Precautions Read and follow these precautions before you install the PanelView 5310
terminal.
Environment and Enclosure Information
ATTENTION: This equipment is intended for use in a Pollution Degree 2
industrial environment, in overvoltage Category II applications (as defined in IEC
60664-1), at altitudes up to 2000 m (6561 ft) without derating. The terminals
are intended for use with programmable logic controllers.
This equipment is considered Group 1, Class A industrial equipment according to IEC
CISPR 11. Without appropriate precautions, there can be difficulties with
electromagnetic compatibility in residential and other environments due to
conducted or radiated disturbances.
Korean Radio Wave Suitability Registration - When so marked this
equipment is registered for Electromagnetic Conformity Registration as
business equipment (A), not home equipment. Sellers or users are
required to take caution in this regard.
이 기기는 업무용 (A 급 ) 전자파적합기기로서 판 매자 또
는 사용자는 이 점을 주의하시기 바 라 며 , 가정외의 지역
에서 사용하는 것을 목적으 로 합니다 .
This equipment is supplied as open-type equipment. It must be mounted within an
enclosure that is suitably designed for those specific environmental conditions that
can be present, and appropriately designed to help prevent personal injury
resulting from accessibility to live parts. The interior of the enclosure must be
accessible only by the use of a tool. The terminals meet specified NEMA, UL Type,
and IEC ratings only when mounted in a panel or enclosure with the equivalent
rating. Subsequent sections of this publication can contain additional information
regarding specific enclosure type ratings that are required to comply with certain
product safety certifications.
In addition to this publication, see the following:
• Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1,
for additional installation requirements.
• NEMA 250 and IEC 60529, as applicable, for explanations of the degrees of
protection provided by different types of enclosure.