Rohde & Schwarz DIB-500 R4.1 User manual

90DIB500IM02 – 5.2
Secure Communications
Installation and Operation Manual
DIB-500 R4.1
Digital Indoor Base Station
Installation and Operation Manual

DIB-500 R4.1
II Installation and Operation Manual 90DIB500IM02 – 5.2
© 2010 Rohde & Schwarz Professional Mobile Radio GmbH
31848 Bad Münder, Germany
Printed in Germany - Subject to change - Data without tolerance limits is not binding.
Encryption components are subject to German export regulations.

Installation and Operation Manual 90DIB500IM02 – 5.2 III
DIB-500 R4.1 Digital Indoor Base Station
Table of contents
1 Notes on the Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
1.1 Objectives of the document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.2 Reading and navigation aids in the document . . . . . . . . . . . . . . . . . . . . . 11
1.3 Target group of the document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.4 Qualification of personnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1.5 Figures and special notations used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1.5.1 Figures used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1.5.2 Special notations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1.5.2.1 Designation of components installed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1.5.2.2 Sequence of actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1.5.2.3 Safety instructions used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1.5.2.4 General instructions used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1.6 History of changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1.7 Further applicable documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1.8 Support information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2 Safety regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
2.1 Safety instructions and declaration of conformity . . . . . . . . . . . . . . . . . . 17
2.2 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.3 Safety measures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.3.1 Authorised personnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.3.2 Electromagnetic compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.3.3 Notes on the electrical system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.3.4 Hazardous substances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.3.5 Product disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

DIB-500 R4.1
IV Installation and Operation Manual 90DIB500IM02 – 5.2
3 Product description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
3.1 Antenna coupling variants of the DIB-500 R4.1 . . . . . . . . . . . . . . . . . . . . 23
3.2 Components of the DIB-500 R4.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.2.1 TETRA Indoor Base Transceiver (TIB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.2.1.1 Multi Processor Server Unit (MSU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
PowerPC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Switching and Routing Server (SRS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Processing Unit Controller (PUC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
GPS module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3.2.1.2 IntelPC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
TETRA Operation Server (TOS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Network Element Manager (NEM-523) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3.2.1.3 Synthesizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.2.1.4 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.2.1.5 Receiver/transmitter (carrier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.2.2 Antenna Coupling System (ACS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.2.3 Voltage supply and alarming system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3.2.3.1 Mounting frame (optional for VDC voltage supply) . . . . . . . . . . . . . . . . . . . . 33
3.2.3.2 System controller (optional for VDC voltage supply) . . . . . . . . . . . . . . . . . . . 34
3.2.3.3 Alarm input/output module (optional with VDC voltage supply) . . . . . . . . . . . 36
3.2.3.4 VAC voltage supply unit (optional) including AC voltage supply module(s) . . 37
3.2.4 Connection panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
3.2.4.1 Connection panel (variant without LAN Routing Unit, LRU) . . . . . . . . . . . . . . 39
3.2.4.2 Connection panel (variant with LAN Routing Unit, LRU
[redundancy package]) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
LAN Routing Unit (LRU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
3.2.5 Fan unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Installation and Operation Manual 90DIB500IM02 – 5.2 V
DIB-500 R4.1
3.3 Interfaces of the DIB-500 R4.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
3.4 Wiring diagrams of the DIB-500 R4.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
3.4.1 Internal wiring of the hybrid variant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3.4.1.1 Internal wiring of the hybrid variant – two carriers . . . . . . . . . . . . . . . . . . . . . 44
3.4.1.2 Internal wiring of the hybrid variant – four carriers . . . . . . . . . . . . . . . . . . . . . 45
3.4.1.3 Hybrid variant – eight carriers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
3.4.1.4 Hybrid variant – eight carriers (variant with LAN routing unit, LRU
[redundancy package]) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
3.4.2 Wiring of the cavity variant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
3.4.2.1 Cavity variant – four carriers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
3.4.2.2 Cavity variant – eight carriers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
3.4.3 Internal wiring of the high-power variant – one carrier . . . . . . . . . . . . . . . . . . 55
3.5 Voltage supply of the DIB-500 R4.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
3.6 Scope of delivery of the DIB-500 R4.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
4 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
4.1 Setup variants of the DIB-500 R4.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
4.1.1 Hybrid variant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
4.1.2 Cavity variant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
4.1.3 High power variant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
4.2 Safety measures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
4.3 Installing equipment racks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
4.4 Connecting equipment racks (as of 5 carriers) . . . . . . . . . . . . . . . . . . . . . 63
4.4.1 Removing the top cover of the equipment rack . . . . . . . . . . . . . . . . . . . . . . . 63
4.4.2 Mounting the LRU (optional, variants with redundancy package
only – depending on the delivery status) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
4.4.2.1 Tools and aids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

DIB-500 R4.1
VI Installation and Operation Manual 90DIB500IM02 – 5.2
4.4.2.2 Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
4.4.2.3 Installing the left top hat rail end bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
4.4.2.4 Establishing the voltage supply of the LRU . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Connecting the voltage supply of the top hat rail power supply unit . . . . . . . 68
Connecting voltage supply cables to the top hat rail power supply unit . . . . . 69
4.4.2.5 Inserting the LRU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
4.4.2.6 Installing the top hat rail power supply unit . . . . . . . . . . . . . . . . . . . . . . . . . . 72
4.4.2.7 Installing the right top hat rail end bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
4.4.3 Connecting the equipment racks A and B . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
4.4.3.1 Procedure for connecting equipment racks A and B . . . . . . . . . . . . . . . . . . . 75
5 Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
5.1 Connection to the electrical system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
5.1.1 Tools and aids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
5.1.2 Connection with the grounding system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
5.1.3 Connecting the voltage supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
5.1.3.1 Connecting the VDC voltage supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
5.1.3.2 Connecting the VAC voltage supply (optional) . . . . . . . . . . . . . . . . . . . . . . . . 84
5.1.4 Connecting E1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
5.1.4.1 Connecting E1 connectors (RJ-45) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
5.1.4.2 Connecting E1 (LSA+) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
5.2 Installing the GPS antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
5.3 Connecting antennas (GPS and TETRA) . . . . . . . . . . . . . . . . . . . . . . . . . . 93
5.4 Connecting external alarm sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
5.5 Connecting external alarms (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
5.5.1 Tools and aids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
5.5.2 Removing the top cover of the equipment rack . . . . . . . . . . . . . . . . . . . . . . . 97

Installation and Operation Manual 90DIB500IM02 – 5.2 VII
DIB-500 R4.1
5.5.3 Connecting external alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
5.5.4 Mounting the top cover of the mounting frame . . . . . . . . . . . . . . . . . . . . . . . 101
5.6 Mounting the top cover of the equipment rack . . . . . . . . . . . . . . . . . . . . 101
5.7 Configuring the DIB-500 R4.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
5.7.1 Tools and aids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
5.7.2 Preparatory measures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
5.7.2.1 Switching on the voltage source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
5.7.2.2 Switching on the equipment rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
5.7.2.3 Connecting the service computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Connecting the service computer (serially) . . . . . . . . . . . . . . . . . . . . . . . . . 105
Connecting the SMT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Connecting the service computer (serially) . . . . . . . . . . . . . . . . . . . . . . . . . 106
Connecting the service computer (Ethernet) . . . . . . . . . . . . . . . . . . . . . . . . 106
5.7.3 Deleting the ARP buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
5.7.4 Configuring and generating network configurations via the
NMC-515 ConfigurationManager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
5.7.5 Creating the download repository . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
5.7.6 Adapting the IP address (with more than one TIB module) . . . . . . . . . . . . . 108
5.7.6.1 Adapting the IP addresses (IntelPC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
5.7.6.2 Adapting the IP addresses (PowerPC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
5.7.7 Performing an initial download via NMC-522 DownloadManager . . . . . . . . 115
5.8 Setting a cavity coupler to the TX frequency . . . . . . . . . . . . . . . . . . . . . 115
5.8.1 Tools and aids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
5.8.2 Setting the output power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
5.8.3 Measuring and checking the carriers (impedance adjustment) . . . . . . . . . . 119
5.9 Function tests DIB-500 R4.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
5.9.1 Tools and aids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

DIB-500 R4.1
VIII Installation and Operation Manual 90DIB500IM02 – 5.2
5.9.2 Checking operating statuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
5.9.2.1 Checking operating statuses (via the NMC-511 FaultManager) . . . . . . . . . 123
5.9.2.2 Checking operating statuses (via the Service and Maintenance Tool, SMT) 124
5.9.2.3 Checking operating statuses (via LEDs of the TIB) . . . . . . . . . . . . . . . . . . . 125
5.9.2.4 Checking operating statuses (via LEDs of the voltage supply unit) – optional
(only for VAC voltage supply) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
5.9.3 Checking voice channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
5.9.3.1 Checking the voice channel (two carriers) . . . . . . . . . . . . . . . . . . . . . . . . . . 127
5.9.3.2 Checking the voice channel (more than two carriers) . . . . . . . . . . . . . . . . . 129
5.9.4 Checking the installation site of the GPS antenna . . . . . . . . . . . . . . . . . . . . 130
5.9.5 Concluding tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
6 Service interruption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .133
6.1 Temporary service interruption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
6.2 Permanent shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
7 Recommissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137
7.1 Recommissioning after a temporary service interruption . . . . . . . . . . . 137
7.2 Recommissioning after a permanent shutdown . . . . . . . . . . . . . . . . . . . 138
8 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .139
8.1 Maintenance tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
8.2 Periodical visual inspections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
9 Transport and storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .141
9.1 Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
9.2 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142

Installation and Operation Manual 90DIB500IM02 – 5.2 11
DIB-500 R4.1 Notes on the Document
Objectives of the document
1 Notes on the Document
This chapter provides information on using the document. In addition, it names the
requirements for using the product/system.
1.1 Objectives of the document
The present document contains instructions for behaviour of Rohde & Schwarz Profes-
sional Mobile Radio GmbH for all the persons involved in installing the equipment rack
and commissioning the product.
The present document describes the components and mode of operation of the product
used in the ACCESSNET®-T mobile radio system.
1.2 Reading and navigation aids in the document
As reading and navigation aids, overview tables have been provided at the beginning of
the respective chapters in the present document, for example Table 5.1 on page 77.
These are to provide the reader with an overview of the tasks to be performed. In addi-
tion, they indicate the order in which the tasks are to be performed. When you have
completed a work step, always navigate to the next work step via the overview table to
ensure that the tasks are performed in the correct order. The overview tables are useful
for readers of the printed document (indication of the corresponding sections) as well as
for readers of a PDF document at the PC (via active cross-references to the corre-
sponding sections).
Among other topics, the present document provides information on/instructions for:
|safety regulations
|the product - in the form of a product description
|installing the product
|connecting the electrical system of the product
|commissioning the product and taking it out of operation
1.3 Target group of the document
The present document is intended for all the persons, who
|operate an ACCESSNET®-T network
|install the product on site
|connect the electrical system of the product on site
|commission / shut down the product
Each person commissioned with performing the tasks mentioned above with or on the
system must have read and understood the present document and the associated
accompanying documentation.

DIB-500 R4.1 Notes on the Document
Qualification of personnel
12 Installation and Operation Manual 90DIB500IM02 – 5.2
1.4 Qualification of personnel
Specialists are persons, who:
|are trained and experienced in the corresponding field.
|are familiar with the applicable standards, regulations and provisions associated
with the corresponding task.
1.5 Figures and special notations used
Figures and symbols are used in the present document. They serve for presenting the
product and for emphasizing particular pieces of information.
1.5.1 Figures used
The figures used in this document show the product in a simplified form where neces-
sary for clarity (e.g. technical drawings). They are based on the standard variant of the
serial equipment or module.
1.5.2 Special notations
The special notations described in the following serve for the enhanced comprehensibil-
ity of information. They emphasize specific pieces of information, help you to recognize
this information fast and take corresponding measures.
1.5.2.1 Designation of components installed
In favour of an enhanced comprehensibility, the product names of the installed (net-
work/hardware) components will be abbreviated in the present document. The numeric
specification of the respective (network/hardware) component will also be omitted, e.g.
the addition -500.
For a unique designation of the (network/hardware) components installed in your net-
work element, please refer to the type label, on which every (network/hardware) compo-
nent inside the equipment rack is detailed.
1.5.2.2 Sequence of actions
Standard operation procedures guide you step by step through a sequence of actions
until you have reached the desired goal.
Example of a sequence of actions:
Goal of the actions
Preparation:
✓List of the prerequisite(s) for an action
✓...

Installation and Operation Manual 90DIB500IM02 – 5.2 13
DIB-500 R4.1 Notes on the Document
Figures and special notations used
Carry out the following steps:
➔Description of an individual work step.
➥A possible result of the work step just performed.
1. Description of the first of multiple work steps.
➥A possible result of the work step just performed.
2. Description of the second work step.
✓Confirmation: Results of the entire sequence of actions.
1.5.2.3 Safety instructions used
Safety instructions in this document point to a hazard that may put persons or the prod-
uct/system at risk.
Safety instructions will point out:
|the nature of the hazard,
|the source of the hazard,
|measures to be taken to avert the specified hazard.
Shown below are four safety advice symbols which indicate the severity of the danger
by means of different keywords (danger, warning, caution, attention). The symbols
shown may vary depending on the nature and source of the danger.
This symbol identifies safety instructions. You are warned of an imminent dan-
ger for the life or health of persons.
➔The arrow identifies a precautionary measure designed to avert this danger.
This symbol identifies safety instructions. You are warned of a potential hazard
for the life or health of persons.
➔The arrow identifies a precautionary measure designed to avert this danger.
This symbol identifies safety instructions. You are warned of a potentially haz-
ardous situation for the life or health of persons.
➔The arrow identifies a precautionary measure designed to avert this danger.

DIB-500 R4.1 Notes on the Document
History of changes
14 Installation and Operation Manual 90DIB500IM02 – 5.2
This symbol identifies safety instructions. You are alerted of a hazard for the
product/system.
➔The arrow identifies a precautionary measure designed to avert this danger.
1.5.2.4 General instructions used
General instructions provide supplementary and useful information.
Important Information
This symbol identifies information that may assist in handling and using the product/sys-
tem. This includes references to further information.
1.6 History of changes
Table 1.1 displays the implemented changes in this document. Here, it will be distin-
guished between the following reasons for changes:
|Content-related changes (e.g. functional expansions or new features)
|Formal changes (e.g. changes to the layout)
|Fault corrections (product-specific or document-specific corrections)
Introduction of the History of Changes
The history of changes within documents has been introduced as of 2009. From this
time available documents will be provided with the history of changes subsequently dur-
ing the next revision. In this case the history of changes starts with the current docu-
ment version, refer to Table 1.1.
Table 1.1 History of changes
Version Date Reason for changes Implemented changes refer to
5.2 2010-06-25 Content-related
changes Adapting the IP address (with more than one TIB module) Section 5.7.6 on page 108

Installation and Operation Manual 90DIB500IM02 – 5.2 15
DIB-500 R4.1 Notes on the Document
Further applicable documents
1.7 Further applicable documents
Apart from the present documentation, the scope of delivery of the product includes
additional documents. In addition to the contents of the present documentation, all the
other documents associated with the product must always be taken into consideration.
They are mandatory for the use of the product.
These are:
|Technical data,
describe the technical properties of the product
|Site Requirements,
describe the requirements for the site where the product is used.
|Service and Maintenance manual,
describes the maintenance and care of the product as well as the replacement of
the (network/hardware) components installed in the product.
|Configuration Manual NDB-500 (NDB computer)
contains information required for the proper configuration of the product.
|User ManualNMC-511 FaultManager
contains information required for the proper operation of the product.
|User Manual NMC-515 ConfigurationManager
contains information required for the proper operation of the product.
|User Manual NMC-522 DownloadManager
contains information required for the proper operation of the product.
|Requirements Manual "Service Computer for ACCESSNET®-T“
This manual describes the requirements for the service computer used for installing
and commissioning network components of an ACCESSNET®-T as well as for serv-
ice and maintenance purposes.
|Open Source Acknowledgement
contains information on the respective Open Source software the product com-
prises, including the information on the license(s) used and the related license
agreements.
|Project-specific documents, if any, such as the "Base Design“ document:
describes the implemented network and the associated properties and require-
ments
Further applicable documents
Please also heed the documentation of the third-party devices connected to the product
to prevent negative effects or problems with product.

DIB-500 R4.1 Notes on the Document
Support information
16 Installation and Operation Manual 90DIB500IM02 – 5.2
1.8 Support information
If you have any questions or suggestions regarding Rohde & Schwarz Professional
Mobile Radio GmbH products, please contact your local service partner responsible or
the Rohde & Schwarz Professional Mobile Radio GmbH Support Team directly.
For a fast and cost-efficient solution of technical problems during the operation of your
ACCESSNET®-T network, Rohde & Schwarz Professional Mobile Radio GmbH offers
support contracts upon request. For information on this topic, please also revert to our
responsible service partner or directly to Rohde & Schwarz Professional Mobile Radio
GmbH.
Product training courses assist you in making use of the full scope of features and capa-
bilities of your ACCESSNET®-T network. For information on the training program of
Rohde & Schwarz Professional Mobile Radio GmbH, please revert to our responsible
service partner, to Rohde & Schwarz Professional Mobile Radio GmbH or directly to
Rohde & Schwarz.
Rohde & Schwarz Professional Mobile Radio GmbH
Fritz-Hahne-Straße 7
D-31848 Bad Münder
Germany
Telephone:[phone]
Fax: [phone]
www.pmr.rohde-schwarz.com

Installation and Operation Manual 90DIB500IM02 – 5.2 17
DIB-500 R4.1 Safety regulations
Safety instructions and declaration of conformity
2 Safety regulations
This chapter describes the safety regulations relevant for using the product.
2.1 Safety instructions and declaration of conformity
The product has been designed, constructed and tested according to the relevant EN,
DIN and VDE (Association for Electrical, Electronic & Information Technologies) provi-
sions. This is documented by CE marking and the declaration of conformity.
The operation of the product is subject to the statutory provisions of the respective
country, in which the product is used. For the operation, the required operating licences
must be requested from the responsible local authorities. Particularly the frequency
range used must be reserved for the respective purpose in the country, in which the
product is used. The product user is responsible for complying with the intended use
and the statutory provisions.
The product conforms with the general requirements of the responsible European
Directives. This is confirmed by the marking (CE) of the installed components. The Dec-
larations of Conformity of the installed components may be viewed upon request.
The directive on radio equipment and telecommunications terminal equipment (Gesetz
über Funkanlagen und Telekommunikationsendeinrichtungen (FTEG)) implemented by
the European Directive 99/5/EC (R&TTE) is applicable in Germany. The product com-
plies with the fundamental requirements and the other relevant provisions of this direc-
tive.
The product is assigned the equipment class code for radio equipment of class 2 (2.12)
and is marked as follows.
Figure 2.1 Conformity: CE marking
Within the scope of the European Directive 99/5/EC, the network operator must ensure
that the health and safety of the product user and other persons, (Article 3 (1)a of 99/5/
EC and 1999/519/EC) is warranted. With regard to the exposure of persons to electro-
magnetic fields (110 MHz to 40 GHz), product standard EN 50385 must be applied.
Within the EU, the product is intended for use in the following member states: Austria
(AT), Belgium (BE), Bulgaria (BG), Switzerland/Liechtenstein (CH), Cyprus (CY), Czech
Republic (CZ), Germany (DE), Denmark (DK), Estonia (EE), Spain (ES), Finland (FI),
France (FR), Greece (GR), Hungary (HU), Ireland (IE), Iceland (IS), Italy (IT), Lithuania
(LT), Latvia (LV), Netherlands (NL), Norway (NO), Romania (RO), Sweden (SE), Slove-
nia (SI), Slovakia (SK), England (UK).
The use of the respective frequency ranges may vary depending on the country of use.
If you have any questions, please contact Rohde & Schwarz Professional Mobile Radio
GmbH.

DIB-500 R4.1 Safety regulations
Safety instructions and declaration of conformity
18 Installation and Operation Manual 90DIB500IM02 – 5.2
The general instructions on safety and accident prevention are documented in the Acci-
dent Prevention Guideline "General Regulations" (BGV A1).1) . For work performed on
electrical installations, the Accident Prevention Regulations (BGV A3) "Electrical Instal-
lations" must be heeded.
The product complies with the safety requirements of the European Low Voltage Direc-
tive (2006/95/EC [73/23/EEC]) due to the application of the standard EN 60950-1. The
requirements of this standard must not be violated when using the product.
The operator is responsible for ensuring that:
|the product is used exclusively within the scope of the intended use.
|work on the electrical installation is performed only by experts that have been
trained accordingly
|special legal requirements that govern the operation of the product are complied
with
|product modifications or expansions:
– are performed only after having consulted Rohde & Schwarz Professional Mobile
Radio GmbH.
– comply with the state of the art
– take into consideration the applicable national and international provisions
– are performed exclusively by trained specialists, who have been authorized
accordingly.
|damage to the product and product defects are immediately remedied by specialists
that have been trained and authorized accordingly.
|appropriate measures are taken against radio interference.
|any defects in the service room that come up later on are eliminated immediately.
|for subsequent modifications of the service room, the requirements described in the
present document are always taken into consideration.
|appropriate fire precautions are taken as required (e.g. the use of appropriate fire
extinguishers).
|special legal requirements that control the operation and handling of batteries and
battery systems, if used, are complied with and that appropriate safety devices and
measures are provided and taken as required.
Country-specific laws and provisions
All the stipulated laws and provisions of the respective country of use shall always
apply. The operator is responsible for the adherence to these laws and provisions.
1) HVBG: Federation of German Industrial Trade Associations, Sankt Augustin, publisher of
the Accident Prevention Guidelines. For sources of supply, please revert to the responsi-
ble Accident Prevention and Insurance Association office.

Installation and Operation Manual 90DIB500IM02 – 5.2 19
DIB-500 R4.1 Safety regulations
Intended use
2.2 Intended use
The product is exclusively designed for being used as a professional TETRA communi-
cation system. In this application it is used for the wireless communication between sub-
scribers equipped with the corresponding mobile stations as well as for switching calls
and transferring data between subscribers of TETRA (Terrestrial Trunked Radio) net-
works.
Intended use also includes that:
|all the safety instructions set forth in the product documents are always heeded.
|all the maintenance tasks described are performed in the interval specified.
|the general, national and in-house safety regulations are heeded.
Any other use is impermissible.
The product is not used as intended, for example, if:
|the requirements described in the product documents haven not been met and
instructions are disregarded.
|the structural design of the product is modified without the consent of the Rohde &
Schwarz Professional Mobile Radio GmbH.
|replacement parts are used that differ from the components installed by default.
The operator of the product is responsible for damage to the product or damage caused
by the product if the product was used beyond the intended application range and/or
was not used as intended.
2.3 Safety measures
All the regulations listed in the following must be adhered to without fail:
|If extension cables or multiple socket outlets are used, make sure that they are
inspected for proper condition periodically.
|After any safety-related parts have been replaced (e.g. power switch or circuit
breakers) a safety check must be performed (visual inspection, protective earthing
conductor load, leakage resistance, leakage current measurement, function test).
Heed the security labelling!
In addition to the safety instructions set forth in the product documentation, all the safety
markings in the equipment rack must be observed. They point out potential hazardous
areas and must neither be removed nor changed.

DIB-500 R4.1 Safety regulations
Safety measures
20 Installation and Operation Manual 90DIB500IM02 – 5.2
2.3.1 Authorised personnel
The product may be transported, set up, connected, commissioned, operated and serv-
iced only by specialists who are familiar with and comply with the applicable safety reg-
ulations and setup instructions.
The specialists must be authorized to perform the required tasks by the person respon-
sible for the safety in the enterprise of the operator.
Specialists are persons, who:
|are trained and experienced in the corresponding field
|are familiar with the relevant standards, regulations, provisions and safety codes,
and
|have been instructed in the mode of operation and the operating conditions of the
equipment components
|can identify and avert hazards
Depending on the tasks to be performed, the following user groups are distinguished:
|operators, who
– operate the product.
– monitor, interrupt, terminate and restore the operation of the product.
|Service personnel: persons, who perform the following additional tasks as com-
pared to operators
– Set up the product.
– Prepare and restore the operational state.
– Adjust and/or parameterize the product.
– Maintain, look after and repair the product.
Replacing Network and Hardware Components
The replacement of components inside the component cabinet other than network or
hardware noted here must be performed exclusively by service personnel of Rohde &
Schwarz Professional Mobile Radio GmbH or by qualified personnel especially trained
for this job. If you have any questions on this topic, please revert to your responsible
service representative.
2.3.2 Electromagnetic compatibility
With specific products, e.g. HF radio equipment, increased electromagnetic radiation
may occur as a consequence of operation. Taking into consideration that unborn life is
increasingly worthy of being protected, pregnant women should be protected through
appropriate measures. People with personal medical devices such as cardiac pacemak-
ers and hearing aids can also be endangered by electromagnetic radiation. The opera-
tor is obliged to assess operation rooms with a considerable risk of exposure to
radiation and to avert any hazards.
In proper state and when operated properly, the product complies with all the require-
ments in respect of interference radiation according to ETSI EN 301 489-18. The con-
nections conducting HF signals must neither be manipulated nor damaged.
When using the product with active typical transmitters, the requirements of EN 50385
in respect of the health and safety of a user or any other person in high-frequency fields
are met. Compliance with EN 50385 is achieved as of a minimum distance of 1.5 m to

Installation and Operation Manual 90DIB500IM02 – 5.2 21
DIB-500 R4.1 Safety regulations
Safety measures
the transmitting antenna. A typical transmitter is made up of an omni-directional trans-
mitting antenna with an antenna gain of 7.5 dBi installed on a mast with a height of 30 m
and connected to the base station through a 40-m cable.
2.3.3 Notes on the electrical system
The product may be operated only in the operational states specified by the manufac-
turer without impairment of the ventilation.
Make sure that all the safety measures on the equipment, on the connecting cables and
on the load have been taken. Electrical connections may be made/disconnected only
when neither voltage nor current is applied to the equipment. Voltage may still be
present on the outputs of the equipment after the equipment has been switched off.
Only perform those tasks described in the documents included in the scope of delivery
of the product.
2.3.4 Hazardous substances
The product does not contain any substances specified in the Ordinance on Hazardous
Substances, published in BGBL.I p. 1782 ( Gefahrstoffverordnung [Ordinance on Haz-
ardous Substances], abbr. GefStoffV).
2.3.5 Product disposal
The equipment rack as well as all therein installed and, if applicable, marked with the
symbol (refer to Figure 2.2) (network, hardware) components fall within the scope of the
Electrical and Electronic Device Act (ElektroG).
The ElektroG Act combines the requirements of the following EC directives:
|2002/96/EC (WEEE) for electric and electronic equipment wastes and
|2002/95/EC for restricting the use of specific hazardous substances in electrical and
electronic devices (RoHS directive).
The respective products are marked with the attached symbol according to EN 50419,
refer to Figure 2.2.
Figure 2.2 Identification of the product according to EN 50419
Once the service life of a product has ended, the product must not be disposed of in the
standard domestic refuse. Even disposal via the municipal collection points for electric
and electronic wastes is not permitted.

DIB-500 R4.1 Safety regulations
Safety measures
22 Installation and Operation Manual 90DIB500IM02 – 5.2
In favour of an environmentally-friendly disposal or recycling of matters, Rohde &
Schwarz Professional Mobile Radio GmbH has developed a disposal concept and fully
assumes the duty of taking back and disposing of electric and electronic wastes accord-
ing to the ElektroG Act on behalf of the manufacturer.
Please revert to your local service representative or directly to Rohde & Schwarz Pro-
fessional Mobile Radio GmbH to dispose of the product.