Rohde & Schwarz NRT-Z43 User manual

1171.6121.35-01 1 E-1
Manual
Directional Power Sensor
R&SNRT-Z14
1120.5505.02
R&SNRT-Z43
1081.2905.02
R&SNRT-Z44
1081.1309.02
Test and Measurement
深圳德标仪器 135-1095-0799

Dear Customer,
R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KG
Trade names are trademarks of the owners.
深圳德标仪器 135-1095-0799

R&S NRT-Z14/Z43/Z44 Tabbed Divider Overview
1081.1544.32 RE E-7
Tabbed Divider Overview
Contents
Safety Instructions
EC Certificate of Conformity
Customer Support
Tabbed Divider
1Chapter 1: Putting into Operation
2Chapter 2: Operation via Demo Software
3 Chapter 3: Remote Control
4 Chapter 4: Maintenance and Troubleshooting
5 Chapter 4: Testing the Rated Specifications –
Service Documentation
Annex: List of Commands
Index
深圳德标仪器 135-1095-0799

深圳德标仪器 135-1095-0799

R&S NRT-Z14/Z43/Z44 Contents
1081.1544.32 3 E-8
Contents
1Putting into Operation ........................................................................................ 1.1
1.1 Unpacking ...............................................................................................................................1.1
1.2 Connecting the Sensor..........................................................................................................1.1
1.3 Connecting the Sensor to the R&S NRT Power Reflection Meter.....................................1.3
1.4 Operating the Sensor on a PC via the R&S NRT-Z5 USB Interface Adapter ....................1.3
1.4.1 Installing Device Drivers.................................................................................................1.4
1.4.2 Checking and Changing the Virtual COM Port ..............................................................1.5
1.5 Operating the Sensor on a PC via the R&S NRT-Z4 PCMCIA Interface Adapter.............1.6
1.5.1 Installing a PCMCIA Interface Card (SIO Card).............................................................1.6
1.6 Operating the Sensor on a PC via the R&S NRT-Z3 Interface Adapter...........................1.7
1.7 Connection to AC Supply......................................................................................................1.7
2WindowsUser Interface Virtual NRT (Rev. 2.0)........................................... 2.1
2.1 Installation ..............................................................................................................................2.1
2.2 Operation ................................................................................................................................2.1
3Remote Control ................................................................................................... 3.1
3.1 Remote Control via Virtual NRT............................................................................................3.1
3.2 Remote Control via Terminal Program ................................................................................3.2
3.2.1 Interface Configuration of Sensor ..................................................................................3.2
3.2.2 Adaptation of Computer Interface..................................................................................3.2
3.2.3 Testing the Connection ..................................................................................................3.3
3.3 Device-Dependent Messages................................................................................................3.5
3.3.1 Structure and Syntax of Device-Dependent Messages .................................................3.5
3.3.2 Setting Commands and Query Commands ...................................................................3.5
3.3.2.1 Input Parameters...............................................................................................3.6
3.3.3 Device Responses .........................................................................................................3.7
3.3.3.1 Checksum Header ............................................................................................3.8
3.3.3.2 Status Field .......................................................................................................3.8
3.3.3.3 Multiple-Line Responses...................................................................................3.9
3.3.3.4 'busy' Status Message.......................................................................................3.9
3.3.3.5 Status Messages via "?"-Command................................................................3.10
深圳德标仪器 135-1095-0799

Contents R&S NRT-Z14/Z43/Z44
1081.1544.32 4 E-8
3.4 Description of Commands ..................................................................................................3.11
3.4.1 Measurement Functions: Setting Commands..............................................................3.11
3.4.1.1 Overview of Setting Commands......................................................................3.11
3.4.1.2 BURS ..............................................................................................................3.13
3.4.1.3 CCDF ..............................................................................................................3.13
3.4.1.4 DIR ..................................................................................................................3.14
3.4.1.5 DISP................................................................................................................3.14
3.4.1.6 FREQ ..............................................................................................................3.15
3.4.1.7 FILT.................................................................................................................3.15
3.4.1.8 FOR.................................................................................................................3.18
3.4.1.9 MOD................................................................................................................3.21
3.4.1.10 OFFS ..........................................................................................................3.22
3.4.1.11 PEP.............................................................................................................3.22
3.4.1.12 PORT..........................................................................................................3.23
3.4.1.13 RESET........................................................................................................3.24
3.4.1.14 REV ............................................................................................................3.24
3.4.1.15 ZERO..........................................................................................................3.26
3.4.2 Measurement Functions: Query Commands ...............................................................3.27
3.4.2.1 Short Overview................................................................................................3.27
3.4.2.2 FTRG ..............................................................................................................3.27
3.4.2.3 RTRG ..............................................................................................................3.27
3.4.2.4 SPEC...............................................................................................................3.28
3.4.2.5 STAT ...............................................................................................................3.31
3.4.3 General Commands.....................................................................................................3.34
3.4.3.1 Short Overview................................................................................................3.34
3.4.3.2 APPL ...............................................................................................................3.34
3.4.3.3 BOOT ..............................................................................................................3.34
3.4.3.4 DMA ................................................................................................................3.35
3.4.3.5 HELP...............................................................................................................3.35
3.4.3.6 ID.....................................................................................................................3.36
3.4.3.7 PURGE............................................................................................................3.36
3.4.3.8 SETUP ............................................................................................................3.36
3.4.4 Service Functions.........................................................................................................3.37
3.4.4.1 SERV:CS.........................................................................................................3.39
3.4.4.2 SERV:NOISE ..................................................................................................3.39
3.4.4.3 SERV:TEST ....................................................................................................3.40
3.4.5 Calibration Functions ...................................................................................................3.41
3.5 Hardware Functions and Command Processing ..............................................................3.42
3.5.1 Description of Hardware Functions..............................................................................3.42
3.5.2 Description of Command Processing ..........................................................................3.43
3.5.2.1 Device Hardware and Data Record ................................................................3.44
3.5.2.2 Status Reporting System.................................................................................3.44
3.5.2.3 Output Unit ......................................................................................................3.44
3.5.2.4 Cyclic Background Power and Temperature Measurements..........................3.44
3.6 Status Reporting System.....................................................................................................3.45
3.6.1 Device Status...............................................................................................................3.45
深圳德标仪器 135-1095-0799

R&S NRT-Z14/Z43/Z44 Contents
1081.1544.32 5 E-8
3.6.2 Error Status..................................................................................................................3.45
3.6.2.1 Occurrence and Causes of Errors ..................................................................3.46
4Maintenance and Troubleshooting.................................................................... 4.1
4.1 Setting the Baud Rate............................................................................................................4.1
4.2 Firmware Update ....................................................................................................................4.1
4.3 Functional Test.......................................................................................................................4.2
4.3.1 Measuring Instruments and Auxiliary Equipment...........................................................4.2
4.3.2 Power-up Test................................................................................................................4.2
4.3.3 Selftest ...........................................................................................................................4.3
4.3.4 Determining Faulty Boards.............................................................................................4.4
4.3.4.1 Controller Board ................................................................................................4.4
4.3.4.2 Analog Board.....................................................................................................4.5
4.3.4.3 Coupler Board ...................................................................................................4.5
4.3.4.4 Interface Adapter R&S NRT-Z3 ........................................................................4.6
4.4 Replacement of Expendable Parts .......................................................................................4.7
4.4.1 Power Sensor Cable ......................................................................................................4.7
4.4.2 RF Connectors...............................................................................................................4.7
4.4.3 Connection Cable for the Interface Adapter R&S NRT-Z3 ............................................4.8
4.5 Cleaning and Care..................................................................................................................4.8
5Testing the Rated Specifications....................................................................... 5.1
5.1 Measuring Instruments and Auxiliary Equipment ..............................................................5.1
5.2 Test Sequence........................................................................................................................5.2
5.2.1 Testing the AVG Measurement Function.......................................................................5.2
5.2.2 Testing the CCDF Threshold .........................................................................................5.3
5.2.3 Testing the PEP Function ..............................................................................................5.3
5.2.4 Testing the Directivity.....................................................................................................5.4
5.2.5 Testing the Matching......................................................................................................5.4
5.3 Performance Test Report ......................................................................................................5.5
Performance Test Report.................................................................................................................5.6
Annex List of Commands..............................................................................A-1
Figures ........................................................................................................................ 6
Tables.......................................................................................................................... 7
深圳德标仪器 135-1095-0799

Contents Figures
1081.1544.32 6 E-8
Figures
Fig. 1-1 Connection of power sensor...............................................................................................1.1
Fig. 1-2 Connecting the cable to the PCMCIA interface card (SIO card) ............................................1.7
Fig. 2-1 Controls ..................................................................................................................................2.2
Fig. 3-1 Syntax Graph of a Command Line.........................................................................................3.6
Fig. 3-2 Syntax graph of floating-point number ..................................................................................3.7
Fig. 3-3 Syntax graph of integer .........................................................................................................3.7
Fig. 3-4 Envelope power characteristic of a burst signal...................................................................3.13
Fig. 3-5 Averaging filter .....................................................................................................................3.15
Fig. 3-6 Influence of video bandwidth on rectified signal...................................................................3.17
Fig. 3-7 Definition of average burst power shown for a modulated burst sequence................3.19
Fig. 3-8 CCDF function shown for a test signal with stochastic envelope.........................................3.19
Fig. 3-9 Operation of peak hold circuit ..........................................................................................3.21
Fig. 3-10 Definition of test position ......................................................................................................3.24
Fig. 3-11 Functional diagram of hardware...........................................................................................3.42
Fig. 3-12 Functional diagram of command processing .......................................................................3.43
Fig. 4-1 Setting the baud rate (shown for 19200 baud) .......................................................................4.1
Fig. 4-2 Checking the LED status on power-up test............................................................................4.5
Fig. 5-1 Test setup for testing the AVG power indication ....................................................................5.2
Fig. 5-2 Test setup for testing the matching........................................................................................5.4
深圳德标仪器 135-1095-0799

NRT-Z43/Z44 Tables
1081.1544.32 7 E-8
Tables
Table 2-1 Key groups on the user interface ...........................................................................................2.3
Table 2-2 Pop-up menus "Settings", "Sensor" and "Options".................................................................2.4
Table 3-1 Setting Commands...............................................................................................................3.11
Table 3-2 Video bandwidth settings for common waveforms...............................................................3.18
Table 3-3 Reverse measurement functions .........................................................................................3.25
Table 3-4 Query commands.................................................................................................................3.27
Table 3-5 Specifications .......................................................................................................................3.29
Table 3-6 General Commands .............................................................................................................3.34
Table 3-7 Service commands...............................................................................................................3.37
Table 3-8 Calibration commands .........................................................................................................3.41
Table 3-9 Error status...........................................................................................................................3.45
Table 4-1 LED status on power-up test ..................................................................................................4.4
Table 5-1 Performance Test Report.......................................................................................................5.5
Table A-1 List of all remote control commands ..................................................................................... A-1
深圳德标仪器 135-1095-0799

深圳德标仪器 135-1095-0799

1171.0000.42 - 08 Page 1
Basic Safety Instructions
Always read through and comply with the following safety instructions!
All plants and locations of the Rohde & Schwarz group of companies make every effort to keep the safety
standards of our products up to date and to offer our customers the highest possible degree of safety. Our
products and the auxiliary equipment they require are designed, built and tested in accordance with the
safety standards that apply in each case. Compliance with these standards is continuously monitored by
our quality assurance system. The product described here has been designed, built and tested in
accordance with the EC Certificate of Conformity and has left the manufacturer’s plant in a condition fully
complying with safety standards. To maintain this condition and to ensure safe operation, you must
observe all instructions and warnings provided in this manual. If you have any questions regarding these
safety instructions, the Rohde & Schwarz group of companies will be happy to answer them.
Furthermore, it is your responsibility to use the product in an appropriate manner. This product is designed
for use solely in industrial and laboratory environments or, if expressly permitted, also in the field and must
not be used in any way that may cause personal injury or property damage. You are responsible if the
product is used for any purpose other than its designated purpose or in disregard of the manufacturer's
instructions. The manufacturer shall assume no responsibility for such use of the product.
The product is used for its designated purpose if it is used in accordance with its product documentation
and within its performance limits (see data sheet, documentation, the following safety instructions). Using
the product requires technical skills and, in some cases, a basic knowledge of English. It is therefore
essential that only skilled and specialized staff or thoroughly trained personnel with the required skills be
allowed to use the product. If personal safety gear is required for using Rohde & Schwarz products, this
will be indicated at the appropriate place in the product documentation. Keep the basic safety instructions
and the product documentation in a safe place and pass them on to the subsequent users.
Observing the safety instructions will help prevent personal injury or damage of any kind caused by
dangerous situations. Therefore, carefully read through and adhere to the following safety instructions
before and when using the product. It is also absolutely essential to observe the additional safety
instructions on personal safety, for example, that appear in relevant parts of the product documentation. In
these safety instructions, the word "product" refers to all merchandise sold and distributed by the Rohde &
Schwarz group of companies, including instruments, systems and all accessories. For product-specific
information, see the data sheet and the product documentation.
Safety labels on products
The following safety labels are used on products to warn against risks and dangers.
Symbol
Meaning
Symbol
Meaning
Notice, general danger location
Observe product documentation
ON/OFF Power
Caution when handling heavy equipment
Standby indication
Danger of electric shock
Direct current (DC)
深圳德标仪器 135-1095-0799

Basic Safety Instructions
1171.0000.42 - 08 Page 2
Symbol
Meaning
Symbol
Meaning
Caution ! Hot surface
Alternating current (AC)
Protective conductor terminal
To identify any terminal which is intended for
connection to an external conductor for
protection against electric shock in case of a
fault, or the terminal of a protective earth
Direct/alternating current (DC/AC)
Earth (Ground)
Class II Equipment
to identify equipment meeting the safety
requirements specified for Class II equipment
(device protected by double or reinforced
insulation)
Frame or chassis Ground terminal
EU labeling for batteries and accumulators
For additional information, see section "Waste
disposal/Environmental protection", item 1.
Be careful when handling electrostatic sensitive
devices
EU labeling for separate collection of electrical
and electronic devices
For additional information, see section "Waste
disposal/Environmental protection", item 2.
Warning! Laser radiation
For additional information, see section
"Operation", item 7.
Signal words and their meaning
The following signal words are used in the product documentation in order to warn the reader about risks
and dangers.
Indicates a hazardous situation which, if not avoided, will result in death or
serious injury.
Indicates a hazardous situation which, if not avoided, could result in death or
serious injury.
Indicates a hazardous situation which, if not avoided, could result in minor or
moderate injury.
Indicates information considered important, but not hazard-related, e.g.
messages relating to property damage.
In the product documentation, the word ATTENTION is used synonymously.
These signal words are in accordance with the standard definition for civil applications in the European
Economic Area. Definitions that deviate from the standard definition may also exist in other economic
areas or military applications. It is therefore essential to make sure that the signal words described here
are always used only in connection with the related product documentation and the related product. The
use of signal words in connection with unrelated products or documentation can result in misinterpretation
and in personal injury or material damage.
深圳德标仪器 135-1095-0799

Basic Safety Instructions
1171.0000.42 - 08 Page 3
Operating states and operating positions
The product may be operated only under the operating conditions and in the positions specified by the
manufacturer, without the product's ventilation being obstructed. If the manufacturer's specifications are
not observed, this can result in electric shock, fire and/or serious personal injury or death. Applicable local
or national safety regulations and rules for the prevention of accidents must be observed in all work
performed.
1. Unless otherwise specified, the following requirements apply to Rohde & Schwarz products:
predefined operating position is always with the housing floor facing down, IP protection 2X, use only
indoors, max. operating altitude 2000 m above sea level, max. transport altitude 4500 m above sea
level. A tolerance of ±10 % shall apply to the nominal voltage and ±5 % to the nominal frequency,
overvoltage category 2, pollution degree 2.
2. Do not place the product on surfaces, vehicles, cabinets or tables that for reasons of weight or stability
are unsuitable for this purpose. Always follow the manufacturer's installation instructions when
installing the product and fastening it to objects or structures (e.g. walls and shelves). An installation
that is not carried out as described in the product documentation could result in personal injury or
even death.
3. Do not place the product on heat-generating devices such as radiators or fan heaters. The ambient
temperature must not exceed the maximum temperature specified in the product documentation or in
the data sheet. Product overheating can cause electric shock, fire and/or serious personal injury or
even death.
Electrical safety
If the information on electrical safety is not observed either at all or to the extent necessary, electric shock,
fire and/or serious personal injury or death may occur.
1. Prior to switching on the product, always ensure that the nominal voltage setting on the product
matches the nominal voltage of the mains-supply network. If a different voltage is to be set, the power
fuse of the product may have to be changed accordingly.
2. In the case of products of safety class I with movable power cord and connector, operation is
permitted only on sockets with a protective conductor contact and protective conductor.
3. Intentionally breaking the protective conductor either in the feed line or in the product itself is not
permitted. Doing so can result in the danger of an electric shock from the product. If extension cords
or connector strips are implemented, they must be checked on a regular basis to ensure that they are
safe to use.
4. If there is no power switch for disconnecting the product from the mains, or if the power switch is not
suitable for this purpose, use the plug of the connecting cable to disconnect the product from the
mains. In such cases, always ensure that the power plug is easily reachable and accessible at all
times. For example, if the power plug is the disconnecting device, the length of the connecting cable
must not exceed 3 m. Functional or electronic switches are not suitable for providing disconnection
from the AC supply network. If products without power switches are integrated into racks or systems,
the disconnecting device must be provided at the system level.
5. Never use the product if the power cable is damaged. Check the power cables on a regular basis to
ensure that they are in proper operating condition. By taking appropriate safety measures and
carefully laying the power cable, ensure that the cable cannot be damaged and that no one can be
hurt by, for example, tripping over the cable or suffering an electric shock.
深圳德标仪器 135-1095-0799

Basic Safety Instructions
1171.0000.42 - 08 Page 4
6. The product may be operated only from TN/TT supply networks fuse-protected with max. 16 A (higher
fuse only after consulting with the Rohde & Schwarz group of companies).
7. Do not insert the plug into sockets that are dusty or dirty. Insert the plug firmly and all the way into the
socket provided for this purpose. Otherwise, sparks that result in fire and/or injuries may occur.
8. Do not overload any sockets, extension cords or connector strips; doing so can cause fire or electric
shocks.
9. For measurements in circuits with voltages Vrms > 30 V, suitable measures (e.g. appropriate
measuring equipment, fuse protection, current limiting, electrical separation, insulation) should be
taken to avoid any hazards.
10. Ensure that the connections with information technology equipment, e.g. PCs or other industrial
computers, comply with the IEC 60950-1 / EN 60950-1 or IEC 61010-1 / EN 61010-1 standards that
apply in each case.
11. Unless expressly permitted, never remove the cover or any part of the housing while the product is in
operation. Doing so will expose circuits and components and can lead to injuries, fire or damage to the
product.
12. If a product is to be permanently installed, the connection between the protective conductor terminal
on site and the product's protective conductor must be made first before any other connection is
made. The product may be installed and connected only by a licensed electrician.
13. For permanently installed equipment without built-in fuses, circuit breakers or similar protective
devices, the supply circuit must be fuse-protected in such a way that anyone who has access to the
product, as well as the product itself, is adequately protected from injury or damage.
14. Use suitable overvoltage protection to ensure that no overvoltage (such as that caused by a bolt of
lightning) can reach the product. Otherwise, the person operating the product will be exposed to the
danger of an electric shock.
15. Any object that is not designed to be placed in the openings of the housing must not be used for this
purpose. Doing so can cause short circuits inside the product and/or electric shocks, fire or injuries.
16. Unless specified otherwise, products are not liquid-proof (see also section "Operating states and
operating positions", item 1). Therefore, the equipment must be protected against penetration by
liquids. If the necessary precautions are not taken, the user may suffer electric shock or the product
itself may be damaged, which can also lead to personal injury.
17. Never use the product under conditions in which condensation has formed or can form in or on the
product, e.g. if the product has been moved from a cold to a warm environment. Penetration by water
increases the risk of electric shock.
18. Prior to cleaning the product, disconnect it completely from the power supply (e.g. AC supply network
or battery). Use a soft, non-linting cloth to clean the product. Never use chemical cleaning agents such
as alcohol, acetone or diluents for cellulose lacquers.
Operation
1. Operating the products requires special training and intense concentration. Make sure that persons
who use the products are physically, mentally and emotionally fit enough to do so; otherwise, injuries
or material damage may occur. It is the responsibility of the employer/operator to select suitable
personnel for operating the products.
深圳德标仪器 135-1095-0799

Basic Safety Instructions
1171.0000.42 - 08 Page 5
2. Before you move or transport the product, read and observe the section titled "Transport".
3. As with all industrially manufactured goods, the use of substances that induce an allergic reaction
(allergens) such as nickel cannot be generally excluded. If you develop an allergic reaction (such as a
skin rash, frequent sneezing, red eyes or respiratory difficulties) when using a Rohde & Schwarz
product, consult a physician immediately to determine the cause and to prevent health problems or
stress.
4. Before you start processing the product mechanically and/or thermally, or before you take it apart, be
sure to read and pay special attention to the section titled "Waste disposal/Environmental protection",
item 1.
5. Depending on the function, certain products such as RF radio equipment can produce an elevated
level of electromagnetic radiation. Considering that unborn babies require increased protection,
pregnant women must be protected by appropriate measures. Persons with pacemakers may also be
exposed to risks from electromagnetic radiation. The employer/operator must evaluate workplaces
where there is a special risk of exposure to radiation and, if necessary, take measures to avert the
potential danger.
6. Should a fire occur, the product may release hazardous substances (gases, fluids, etc.) that can
cause health problems. Therefore, suitable measures must be taken, e.g. protective masks and
protective clothing must be worn.
7. Laser products are given warning labels that are standardized according to their laser class. Lasers
can cause biological harm due to the properties of their radiation and due to their extremely
concentrated electromagnetic power. If a laser product (e.g. a CD/DVD drive) is integrated into a
Rohde & Schwarz product, absolutely no other settings or functions may be used as described in the
product documentation. The objective is to prevent personal injury (e.g. due to laser beams).
8. EMC classes (in line with EN 55011/CISPR 11, and analogously with EN 55022/CISPR 22,
EN 55032/CISPR 32)
Class A equipment:
Equipment suitable for use in all environments except residential environments and environments
that are directly connected to a low-voltage supply network that supplies residential buildings
Note: Class A equipment is intended for use in an industrial environment. This equipment may
cause radio disturbances in residential environments, due to possible conducted as well as
radiated disturbances. In this case, the operator may be required to take appropriate measures to
eliminate these disturbances.
Class B equipment:
Equipment suitable for use in residential environments and environments that are directly
connected to a low-voltage supply network that supplies residential buildings
Repair and service
1. The product may be opened only by authorized, specially trained personnel. Before any work is
performed on the product or before the product is opened, it must be disconnected from the AC supply
network. Otherwise, personnel will be exposed to the risk of an electric shock.
深圳德标仪器 135-1095-0799

Basic Safety Instructions
1171.0000.42 - 08 Page 6
2. Adjustments, replacement of parts, maintenance and repair may be performed only by electrical
experts authorized by Rohde & Schwarz. Only original parts may be used for replacing parts relevant
to safety (e.g. power switches, power transformers, fuses). A safety test must always be performed
after parts relevant to safety have been replaced (visual inspection, protective conductor test,
insulation resistance measurement, leakage current measurement, functional test). This helps ensure
the continued safety of the product.
Batteries and rechargeable batteries/cells
If the information regarding batteries and rechargeable batteries/cells is not observed either at all or to the
extent necessary, product users may be exposed to the risk of explosions, fire and/or serious personal
injury, and, in some cases, death. Batteries and rechargeable batteries with alkaline electrolytes (e.g.
lithium cells) must be handled in accordance with the EN 62133 standard.
1. Cells must not be taken apart or crushed.
2. Cells or batteries must not be exposed to heat or fire. Storage in direct sunlight must be avoided.
Keep cells and batteries clean and dry. Clean soiled connectors using a dry, clean cloth.
3. Cells or batteries must not be short-circuited. Cells or batteries must not be stored in a box or in a
drawer where they can short-circuit each other, or where they can be short-circuited by other
conductive materials. Cells and batteries must not be removed from their original packaging until they
are ready to be used.
4. Cells and batteries must not be exposed to any mechanical shocks that are stronger than permitted.
5. If a cell develops a leak, the fluid must not be allowed to come into contact with the skin or eyes. If
contact occurs, wash the affected area with plenty of water and seek medical aid.
6. Improperly replacing or charging cells or batteries that contain alkaline electrolytes (e.g. lithium cells)
can cause explosions. Replace cells or batteries only with the matching Rohde & Schwarz type (see
parts list) in order to ensure the safety of the product.
7. Cells and batteries must be recycled and kept separate from residual waste. Rechargeable batteries
and normal batteries that contain lead, mercury or cadmium are hazardous waste. Observe the
national regulations regarding waste disposal and recycling.
Transport
1. The product may be very heavy. Therefore, the product must be handled with care. In some cases,
the user may require a suitable means of lifting or moving the product (e.g. with a lift-truck) to avoid
back or other physical injuries.
2. Handles on the products are designed exclusively to enable personnel to transport the product. It is
therefore not permissible to use handles to fasten the product to or on transport equipment such as
cranes, fork lifts, wagons, etc. The user is responsible for securely fastening the products to or on the
means of transport or lifting. Observe the safety regulations of the manufacturer of the means of
transport or lifting. Noncompliance can result in personal injury or material damage.
3. If you use the product in a vehicle, it is the sole responsibility of the driver to drive the vehicle safely
and properly. The manufacturer assumes no responsibility for accidents or collisions. Never use the
product in a moving vehicle if doing so could distract the driver of the vehicle. Adequately secure the
product in the vehicle to prevent injuries or other damage in the event of an accident.
深圳德标仪器 135-1095-0799

Instrucciones de seguridad elementales
1171.0000.42 - 08 Page 7
Waste disposal/Environmental protection
1. Specially marked equipment has a battery or accumulator that must not be disposed of with unsorted
municipal waste, but must be collected separately. It may only be disposed of at a suitable collection
point or via a Rohde & Schwarz customer service center.
2. Waste electrical and electronic equipment must not be disposed of with unsorted municipal waste, but
must be collected separately.
Rohde & Schwarz GmbH & Co. KG has developed a disposal concept and takes full responsibility for
take-back obligations and disposal obligations for manufacturers within the EU. Contact your
Rohde & Schwarz customer service center for environmentally responsible disposal of the product.
3. If products or their components are mechanically and/or thermally processed in a manner that goes
beyond their intended use, hazardous substances (heavy-metal dust such as lead, beryllium, nickel)
may be released. For this reason, the product may only be disassembled by specially trained
personnel. Improper disassembly may be hazardous to your health. National waste disposal
regulations must be observed.
4. If handling the product releases hazardous substances or fuels that must be disposed of in a special
way, e.g. coolants or engine oils that must be replenished regularly, the safety instructions of the
manufacturer of the hazardous substances or fuels and the applicable regional waste disposal
regulations must be observed. Also observe the relevant safety instructions in the product
documentation. The improper disposal of hazardous substances or fuels can cause health problems
and lead to environmental damage.
For additional information about environmental protection, visit the Rohde & Schwarz website.
Instrucciones de seguridad elementales
¡Es imprescindible leer y cumplir las siguientes instrucciones e informaciones de seguridad!
El principio del grupo de empresas Rohde & Schwarz consiste en tener nuestros productos siempre al día
con los estándares de seguridad y de ofrecer a nuestros clientes el máximo grado de seguridad. Nuestros
productos y todos los equipos adicionales son siempre fabricados y examinados según las normas de
seguridad vigentes. Nuestro sistema de garantía de calidad controla constantemente que sean cumplidas
estas normas. El presente producto ha sido fabricado y examinado según el certificado de conformidad
de la UE y ha salido de nuestra planta en estado impecable según los estándares técnicos de seguridad.
Para poder preservar este estado y garantizar un funcionamiento libre de peligros, el usuario deberá
atenerse a todas las indicaciones, informaciones de seguridad y notas de alerta. El grupo de empresas
Rohde & Schwarz está siempre a su disposición en caso de que tengan preguntas referentes a estas
informaciones de seguridad.
Además queda en la responsabilidad del usuario utilizar el producto en la forma debida. Este producto
está destinado exclusivamente al uso en la industria y el laboratorio o, si ha sido expresamente
autorizado, para aplicaciones de campo y de ninguna manera deberá ser utilizado de modo que alguna
persona/cosa pueda sufrir daño. El uso del producto fuera de sus fines definidos o sin tener en cuenta las
instrucciones del fabricante queda en la responsabilidad del usuario. El fabricante no se hace en ninguna
forma responsable de consecuencias a causa del mal uso del producto.
深圳德标仪器 135-1095-0799

Instrucciones de seguridad elementales
1171.0000.42 - 08 Page 8
Se parte del uso correcto del producto para los fines definidos si el producto es utilizado conforme a las
indicaciones de la correspondiente documentación del producto y dentro del margen de rendimiento
definido (ver hoja de datos, documentación, informaciones de seguridad que siguen). El uso del producto
hace necesarios conocimientos técnicos y ciertos conocimientos del idioma inglés. Por eso se debe tener
en cuenta que el producto solo pueda ser operado por personal especializado o personas instruidas en
profundidad con las capacidades correspondientes. Si fuera necesaria indumentaria de seguridad para el
uso de productos de Rohde & Schwarz, encontraría la información debida en la documentación del
producto en el capítulo correspondiente. Guarde bien las informaciones de seguridad elementales, así
como la documentación del producto, y entréguelas a usuarios posteriores.
Tener en cuenta las informaciones de seguridad sirve para evitar en lo posible lesiones o daños por
peligros de toda clase. Por eso es imprescindible leer detalladamente y comprender por completo las
siguientes informaciones de seguridad antes de usar el producto, y respetarlas durante el uso del
producto. Deberán tenerse en cuenta todas las demás informaciones de seguridad, como p. ej. las
referentes a la protección de personas, que encontrarán en el capítulo correspondiente de la
documentación del producto y que también son de obligado cumplimiento. En las presentes
informaciones de seguridad se recogen todos los objetos que distribuye el grupo de empresas
Rohde & Schwarz bajo la denominación de "producto", entre ellos también aparatos, instalaciones así
como toda clase de accesorios. Los datos específicos del producto figuran en la hoja de datos y en la
documentación del producto.
Señalización de seguridad de los productos
Las siguientes señales de seguridad se utilizan en los productos para advertir sobre riesgos y peligros.
Símbolo
Significado
Símbolo
Significado
Aviso: punto de peligro general
Observar la documentación del producto
Tensión de alimentación de PUESTA EN
MARCHA / PARADA
Atención en el manejo de dispositivos de peso
elevado
Indicación de estado de espera (standby)
Peligro de choque eléctrico
Corriente continua (DC)
Advertencia: superficie caliente
Corriente alterna (AC)
Conexión a conductor de protección
Corriente continua / Corriente alterna (DC/AC)
Conexión a tierra
El aparato está protegido en su totalidad por un
aislamiento doble (reforzado)
Conexión a masa
Distintivo de la UE para baterías y
acumuladores
Más información en la sección
"Eliminación/protección del medio ambiente",
punto 1.
深圳德标仪器 135-1095-0799

Instrucciones de seguridad elementales
1171.0000.42 - 08 Page 9
Símbolo
Significado
Símbolo
Significado
Aviso: Cuidado en el manejo de dispositivos
sensibles a la electrostática (ESD)
Distintivo de la UE para la eliminación por
separado de dispositivos eléctricos y
electrónicos
Más información en la sección
"Eliminación/protección del medio ambiente",
punto 2.
Advertencia: rayo láser
Más información en la sección
"Funcionamiento", punto 7.
Palabras de señal y su significado
En la documentación del producto se utilizan las siguientes palabras de señal con el fin de advertir contra
riesgos y peligros.
Indica una situación de peligro que, si no se evita, causa lesiones
graves o incluso la muerte.
Indica una situación de peligro que, si no se evita, puede causar
lesiones graves o incluso la muerte.
Indica una situación de peligro que, si no se evita, puede causar
lesiones leves o moderadas.
Indica información que se considera importante, pero no en relación
con situaciones de peligro; p. ej., avisos sobre posibles daños
materiales.
En la documentación del producto se emplea de forma sinónima el
término CUIDADO.
Las palabras de señal corresponden a la definición habitual para aplicaciones civiles en el área
económica europea. Pueden existir definiciones diferentes a esta definición en otras áreas económicas o
en aplicaciones militares. Por eso se deberá tener en cuenta que las palabras de señal aquí descritas
sean utilizadas siempre solamente en combinación con la correspondiente documentación del producto y
solamente en combinación con el producto correspondiente. La utilización de las palabras de señal en
combinación con productos o documentaciones que no les correspondan puede llevar a interpretaciones
equivocadas y tener por consecuencia daños en personas u objetos.
Estados operativos y posiciones de funcionamiento
El producto solamente debe ser utilizado según lo indicado por el fabricante respecto a los estados
operativos y posiciones de funcionamiento sin que se obstruya la ventilación. Si no se siguen las
indicaciones del fabricante, pueden producirse choques eléctricos, incendios y/o lesiones graves con
posible consecuencia de muerte. En todos los trabajos deberán ser tenidas en cuenta las normas
nacionales y locales de seguridad del trabajo y de prevención de accidentes.
深圳德标仪器 135-1095-0799

Instrucciones de seguridad elementales
1171.0000.42 - 08 Page 10
1. Si no se convino de otra manera, es para los productos Rohde & Schwarz válido lo que sigue:
como posición de funcionamiento se define por principio la posición con el suelo de la caja para
abajo, modo de protección IP 2X, uso solamente en estancias interiores, utilización hasta 2000 m
sobre el nivel del mar, transporte hasta 4500 m sobre el nivel del mar. Se aplicará una tolerancia de
±10 % sobre el voltaje nominal y de ±5 % sobre la frecuencia nominal. Categoría de sobrecarga
eléctrica 2, índice de suciedad 2.
2. No sitúe el producto encima de superficies, vehículos, estantes o mesas, que por sus características
de peso o de estabilidad no sean aptos para él. Siga siempre las instrucciones de instalación del
fabricante cuando instale y asegure el producto en objetos o estructuras (p. ej. paredes y estantes). Si
se realiza la instalación de modo distinto al indicado en la documentación del producto, se pueden
causar lesiones o, en determinadas circunstancias, incluso la muerte.
3. No ponga el producto sobre aparatos que generen calor (p. ej. radiadores o calefactores). La
temperatura ambiente no debe superar la temperatura máxima especificada en la documentación del
producto o en la hoja de datos. En caso de sobrecalentamiento del producto, pueden producirse
choques eléctricos, incendios y/o lesiones graves con posible consecuencia de muerte.
Seguridad eléctrica
Si no se siguen (o se siguen de modo insuficiente) las indicaciones del fabricante en cuanto a seguridad
eléctrica, pueden producirse choques eléctricos, incendios y/o lesiones graves con posible consecuencia
de muerte.
1. Antes de la puesta en marcha del producto se deberá comprobar siempre que la tensión
preseleccionada en el producto coincida con la de la red de alimentación eléctrica. Si es necesario
modificar el ajuste de tensión, también se deberán cambiar en caso dado los fusibles
correspondientes del producto.
2. Los productos de la clase de protección I con alimentación móvil y enchufe individual solamente
podrán enchufarse a tomas de corriente con contacto de seguridad y con conductor de protección
conectado.
3. Queda prohibida la interrupción intencionada del conductor de protección, tanto en la toma de
corriente como en el mismo producto. La interrupción puede tener como consecuencia el riesgo de
que el producto sea fuente de choques eléctricos. Si se utilizan cables alargadores o regletas de
enchufe, deberá garantizarse la realización de un examen regular de los mismos en cuanto a su
estado técnico de seguridad.
4. Si el producto no está equipado con un interruptor para desconectarlo de la red, o bien si el
interruptor existente no resulta apropiado para la desconexión de la red, el enchufe del cable de
conexión se deberá considerar como un dispositivo de desconexión.
El dispositivo de desconexión se debe poder alcanzar fácilmente y debe estar siempre bien accesible.
Si, p. ej., el enchufe de conexión a la red es el dispositivo de desconexión, la longitud del cable de
conexión no debe superar 3 m).
Los interruptores selectores o electrónicos no son aptos para el corte de la red eléctrica. Si se
integran productos sin interruptor en bastidores o instalaciones, se deberá colocar el interruptor en el
nivel de la instalación.
5. No utilice nunca el producto si está dañado el cable de conexión a red. Compruebe regularmente el
correcto estado de los cables de conexión a red. Asegúrese, mediante las medidas de protección y
de instalación adecuadas, de que el cable de conexión a red no pueda ser dañado o de que nadie
pueda ser dañado por él, p. ej. al tropezar o por un choque eléctrico.
深圳德标仪器 135-1095-0799