Rohde & Schwarz SMB100B User manual

R&S®SMB100B
RF Signal Generator
Getting Started
Getting Started
Version 01
1422104502
(>F:]2)

This document describes the R&S®SMB100B, stock no. 1400.1000.02 and its
options.
© 2018 Rohde & Schwarz GmbH & Co. KG
Mühldorfstr. 15, 81671 München, Germany
Phone: [phone] - 0
Fax: [phone]
Email: [email protected]
Internet: www.rohde-schwarz.com
Subject to change – Data without tolerance limits is not binding.
R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KG.
Trade names are trademarks of the owners.
1422.1045.02 | Version 01 | R&S®SMB100B
The following abbreviations are used throughout this manual: R&S®SMB100B is abbreviated as
R&S SMB100B, R&S®VISA is abbreviated as R&S VISA

1171.1307.42 - 05
1
Safety Instructions
Instrucciones de seguridad
Sicherheitshinweise
Consignes de sécurité
Risk of injury and instrument damage
The instrument must be used in an appropriate manner to prevent
electric shock, fire,
personal injury or instrument damage.
●
Do not open the instrument casing.
●
Read and observe the "Basic Safety Instructions" delivered as
printed brochure with the instrument.
●
Read and observe the safety instructions in the following sections.
Note that the data sheet may specify additional operating conditions.
●
Keep the "Basic Safety Instructions" and the product documentation
in a safe place and pass them on to the subsequent users.
Riesgo de lesiones y daños en el instrumento
El instrumento se debe usar de manera adecuada para p
revenir
descargas eléctricas, incendios, lesiones o daños materiales.
●
No abrir la carcasa del instrumento.
●
Lea y cumpla las "Instrucciones de seguridad elementales"
suministradas con el instrumento como folleto impreso.
●
Lea y cumpla las instrucciones de seguridad incluidas en las
siguientes secciones. Se debe tener en cuenta que las
especificaciones técnicas pueden contener condiciones adicionales
para su uso.
●
Guarde bien las instrucciones de seguridad elementales, así como
la documentación del producto, y entréguelas a usuarios
posteriores.

1171.1307.42 - 05
2
Gefahr von Verletzungen und Schäden am Gerät
Betreiben Sie das Gerät immer ordnungsgemäß, um elektrischen
Schlag, Brand, Verletzungen von Personen oder Geräteschäden zu
verhindern.
●
Öffnen Sie das Gerätegehäuse nicht.
●
Lesen und beachten Sie die "Grundlegenden Sicherheitshinweise",
die als gedruckte Broschüre dem Gerät beiliegen.
●
Lesen und beachten Sie die Sicherheitshinweise in den folgenden
Abschnitten; möglicherweise enthält das Datenblatt weitere
Hinweise zu speziellen Betriebsbedingungen.
●
Bewahren Sie die "Grundlegenden Sicherheitshinweise" und die
Produktdokumentation gut auf und geben Sie diese an weitere
Benutzer des Produkts weiter.
Risque de blessures et d'endommagement de l'appareil
L'ap
pareil doit être utilisé conformément aux prescriptions afin d'éviter
les électrocutions, incendies, dommages corporels et matériels.
●
N'ouvrez pas le boîtier de l'appareil.
●
Lisez et respectez les "consignes de sécurité fondamentales"
fournies avec l’appareil sous forme de brochure imprimée.
●
Lisez et respectez les instructions de sécurité dans les sections
suivantes. Il ne faut pas oublier que la fiche technique peut indiquer
des conditions d’exploitation supplémentaires.
●
Gardez les consignes de sécurité fondamentales et la
documentation produit dans un lieu sûr et transmettez ces
documents aux autres utilisateurs.

Contents
R&S®SMB100B
3Getting Started 1422.1045.02 ─ 01
Contents
1 Preface....................................................................................7
1.1 Key Features......................................................................................... 7
1.2 For Your Safety......................................................................................7
2 Documentation Overview......................................................9
2.1 Getting Started Manual.........................................................................9
2.2 User Manuals and Help........................................................................ 9
2.3 Service Manual......................................................................................9
2.4 Instrument Security Procedures....................................................... 10
2.5 Basic Safety Instructions................................................................... 10
2.6 Data Sheets and Brochures............................................................... 10
2.7 Release Notes and Open Source Acknowledgment (OSA).............10
2.8 Application Notes, Application Cards, White Papers, etc...............11
3 Preparing for Use.................................................................12
3.1 Putting into Operation........................................................................ 12
3.1.1 EMI Suppression...................................................................................13
3.1.2 Unpacking and Checking the Instrument.............................................. 14
3.1.3 Accessory List.......................................................................................14
3.1.4 Placing or Mounting the Instrument...................................................... 14
3.1.5 Connecting AC Power...........................................................................17
3.1.6 Turning the Instrument On and Off....................................................... 17
3.1.7 Functional Check.................................................................................. 19
3.1.8 Checking the Supplied Options and Licenses...................................... 20
3.2 Connecting USB Devices................................................................... 20
3.3 Setting Up a Network (LAN) Connection.......................................... 21
3.3.1 Connecting the Instrument to the Network............................................21

Contents
R&S®SMB100B
4Getting Started 1422.1045.02 ─ 01
4 Instrument Tour................................................................... 24
4.1 Front Panel Tour..................................................................................24
4.1.1 Touchscreen..........................................................................................25
4.1.2 Utility Keys............................................................................................ 26
4.1.3 On/Standby........................................................................................... 26
4.1.4 Function Keys....................................................................................... 27
4.1.5 Keypad..................................................................................................27
4.1.6 Navigation Controls...............................................................................27
4.1.6.1 Rotary Knob.......................................................................................... 28
4.1.6.2 Editing Keys.......................................................................................... 28
4.1.6.3 Navigation Keys.................................................................................... 28
4.1.7 Display Keys......................................................................................... 29
4.1.8 USB Connector..................................................................................... 29
4.1.9 RF 50 Ω.................................................................................................30
4.2 Rear Panel Tour...................................................................................31
4.2.1 Connectors............................................................................................31
5 Trying Out the Instrument...................................................34
5.1 Generating an Unmodulated Carrier................................................. 34
5.2 Generating an RF Frequency Sweep Signal.....................................38
5.3 Saving and Recalling Settings...........................................................40
6 Instrument Control.............................................................. 44
6.1 Possible Ways to Operate the Instrument........................................ 44
6.2 Means of Manual Interaction..............................................................45
6.3 Understanding the Display Information............................................45
6.3.1 Status Bar............................................................................................. 46
6.3.2 Tile Diagram..........................................................................................46
6.3.3 Taskbar................................................................................................. 47

Contents
R&S®SMB100B
5Getting Started 1422.1045.02 ─ 01
6.3.4 Additional Display Characteristics.........................................................48
6.4 Accessing the Functionality.............................................................. 49
6.5 Entering Data.......................................................................................50
6.5.1 Entering Numeric Parameters...............................................................51
6.5.2 Entering Alphanumeric Parameters...................................................... 52
6.5.3 Undo and Redo Actions........................................................................ 52
6.6 Getting Information and Help............................................................ 52
6.7 Remote Control................................................................................... 54
6.8 Remote Operation over VNC..............................................................55
Index..................................................................................... 56

Contents
R&S®SMB100B
6Getting Started 1422.1045.02 ─ 01

Preface
R&S®SMB100B
7Getting Started 1422.1045.02 ─ 01
1 Preface
The R&S SMB100B is a new high-performance signal generator developed to
meet demanding customer requirements. Offering excellent signal characteristic
and straightforward and intuitive operation, the signal generator makes signal
generation fast and easy.
1.1 Key Features
Outstanding key features of the R&S SMB100B are:
●SCPI macro recorder and code generator for generating executable remote
control code from manual operating steps (for MATLAB®, CVI, etc.)
●Frequency range from 8 kHz to 1 GHz, 3 GHz or up to 6 GHz
●Excellent SSB phase noise of -134 dBc (meas.) at 1 GHz, 20 kHz offset
●Low wideband noise. For frequencies between 15 MHz and 6 GHz and 30
MHz offset, < 153 dBc (typ.)
●Ultra high output power of 34 dBm (meas.) for 1 GHz
●Compact rack with a height of 2 U and a ¾ 19" width
●Pulse train generation
●5" Graphical User Interface with touchscreen
For more information, see data sheet.
1.2 For Your Safety
The R&S SMB100B is designated for the development, production and verifica-
tion of electronic components and devices in industrial and laboratory environ-
ments. Use the R&S SMB100B only for its designated purpose. Observe the
operating conditions and performance limits stated in the data sheet.
The product documentation helps you to use the R&S SMB100B safely and effi-
ciently. Keep the product documentation in a safe place and pass it on to the sub-
sequent users.
For Your Safety

Preface
R&S®SMB100B
8Getting Started 1422.1045.02 ─ 01
Safety information is part of the product documentation. It warns you about the
potential dangers and gives instructions how to prevent personal injury or dam-
age caused by dangerous situations. Safety information is provided as follows:
●In the "Basic Safety Instructions", safety issues are grouped according to sub-
jects. For example, one subject is electrical safety. The "Basic Safety Instruc-
tions" are delivered with the R&S SMB100B in different languages in print.
●Throughout the documentation, safety instructions are provided when you
need to take care during setup or operation. Always read the safety instruc-
tions carefully. Make sure to comply fully with them. Do not take risks and do
not underestimate the potential danger of small details such as a damaged
power cable.
For Your Safety

Documentation Overview
R&S®SMB100B
9Getting Started 1422.1045.02 ─ 01
2 Documentation Overview
This section provides an overview of the R&S SMB100B user documentation.
Unless specified otherwise, you find the documents on the R&S SMB100B prod-
uct page at:
www.rohde-schwarz.com/manual/smb100b
2.1 Getting Started Manual
Introduces the R&S SMB100B and describes how to set up and start working with
the product. Includes basic operations, typical measurement examples, and gen-
eral information, e.g. safety instructions, etc. A printed version is delivered with
the instrument.
2.2 User Manuals and Help
Contains the description of all instrument modes and functions. It also provides
an introduction to remote control, a complete description of the remote control
commands with programming examples, and information on maintenance, instru-
ment interfaces and error messages. Includes the contents of the getting started
manual.
The contents of the user manuals are available as help in the R&S SMB100B.
The help offers quick, context-sensitive access to the complete information.
All user manuals are also available for download or for immediate display on the
Internet.
2.3 Service Manual
Describes the performance test for checking the rated specifications, module
replacement and repair, firmware update, troubleshooting and fault elimination,
and contains mechanical drawings and spare part lists.
Service Manual

Documentation Overview
R&S®SMB100B
10Getting Started 1422.1045.02 ─ 01
The service manual is available for registered users on the global
Rohde & Schwarz information system (GLORIS, https://gloris.rohde-
schwarz.com).
2.4 Instrument Security Procedures
Deals with security issues when working with the R&S SMB100B in secure areas.
It is available for download on the Internet.
2.5 Basic Safety Instructions
Contains safety instructions, operating conditions and further important informa-
tion. The printed document is delivered with the instrument.
2.6 Data Sheets and Brochures
The data sheet contains the technical specifications of the R&S SMB100B. It also
lists the options and their order numbers and optional accessories.
The brochure provides an overview of the instrument and deals with the specific
characteristics.
See www.rohde-schwarz.com/brochure-datasheet/smb100b
2.7 Release Notes and Open Source Acknowledg-
ment (OSA)
The release notes list new features, improvements and known issues of the cur-
rent firmware version, and describe the firmware installation.
The open source acknowledgment document provides verbatim license texts of
the used open source software.
See www.rohde-schwarz.com/firmware/smb100b
Release Notes and Open Source Acknowledgment (OSA)

Documentation Overview
R&S®SMB100B
11Getting Started 1422.1045.02 ─ 01
2.8 Application Notes, Application Cards, White
Papers, etc.
These documents deal with special applications or background information on
particular topics.
See www.rohde-schwarz.com/application/smb100b
Application Notes, Application Cards, White Papers, etc.

Preparing for Use
R&S®SMB100B
12Getting Started 1422.1045.02 ─ 01
3 Preparing for Use
●Putting into Operation..................................................................................... 12
●Connecting USB Devices................................................................................20
●Setting Up a Network (LAN) Connection.........................................................21
3.1 Putting into Operation
This section describes the basic steps to be taken when setting up the
R&S SMB100B for the first time.
Risk of injury due to disregarding safety information
Observe the information on appropriate operating conditions provided in the
data sheet to prevent personal injury or damage to the instrument. Read
and observe the basic safety instructions provided with the instrument, in
addition to the safety instructions in the following sections. In particular:
●Do not open the instrument casing.
Risk of instrument damage due to inappropriate operating conditions
Specific operating conditions are required to ensure accurate measure-
ments and to avoid damage to the instrument. Observe the information on
appropriate operating conditions provided in the basic safety instructions
and the instrument's data sheet.
Putting into Operation

Preparing for Use
R&S®SMB100B
13Getting Started 1422.1045.02 ─ 01
Instrument damage caused by electrostatic discharge
Electrostatic discharge (ESD) can damage the electronic components of the
instrument and the device under test (DUT). Electrostatic discharge is most
likely to occur when you connect or disconnect a DUT or test fixture to the
instrument's test ports. To prevent electrostatic discharge, use a wrist strap
and cord and connect yourself to the ground, or use a conductive floor mat
and heel strap combination.
Risk of instrument damage due to inappropriate operating conditions
An unsuitable operating site or test setup can damage the instrument and
connected devices. Before switching on the instrument, observe the infor-
mation on appropriate operating conditions provided in the data sheet. In
particular, ensure the following:
●All fan openings are unobstructed and the airflow perforations are unim-
peded. The minimum distance from the wall is 10 cm.
●The instrument is dry and shows no sign of condensation.
●The instrument is positioned as described in the following sections.
●The ambient temperature does not exceed the range specified in the
data sheet.
●Signal levels at the input connectors are all within the specified ranges.
●Signal outputs are connected correctly and are not overloaded.
3.1.1 EMI Suppression
Electromagnetic interference (EMI) may affect the measurement results.
To suppress generated Electromagnetic Interference (EMI),
●Use suitable shielded cables of high quality. For example use double-shielded
RF, BNC and LAN cables (CAT6 STP).
Note: USB cables are of varying and often poor quality. Therefore, check the
quality of each individual USB cable as described in the service manual.
●Always terminate open cable ends.
Putting into Operation

Preparing for Use
R&S®SMB100B
14Getting Started 1422.1045.02 ─ 01
Note the EMC classification in the data sheet.
3.1.2 Unpacking and Checking the Instrument
Unpack the R&S SMB100B carefully and check the contents of the package.
●Check if all items listed on the delivery note, including this getting started
manual, are included in the delivery.
●Check the R&S SMB100B for any damage.
If the contents are damaged, immediately contact the carrier who delivered
the package.
Packing material
Retain the original packing material. If the instrument needs to be transpor-
ted or shipped later, you can use the material to protect the control ele-
ments and connectors.
Risk of injury during transportation
The carrying handles at the front and side of the casing are designed to lift
or carry the instrument. Do not apply excessive force to the handles. If a
handle is ripped off, the falling instrument can cause injury.
3.1.3 Accessory List
The instrument comes with the following accessories:
●Power cable
●Getting Started printed manual
3.1.4 Placing or Mounting the Instrument
The R&S SMB100B is designed for use under laboratory conditions, either on a
bench top or in a rack using the standard rackmount kit.
Putting into Operation

Preparing for Use
R&S®SMB100B
15Getting Started 1422.1045.02 ─ 01
Bench top operation
If the R&S SMB100B is operated on a bench top, the surface must be flat. The
instrument can be used in horizontal position, standing on its feet, or with the sup-
port feet on the bottom extended.
Risk of injury if feet are folded out
The feet can fold in if they are not folded out completely or if the instrument
is shifted. Collapsing feet can cause injury or damage the instrument.
●Fold the feet completely in or out to ensure stability of the instrument.
Never shift the instrument when the feet are folded out.
●When the feet are folded out, do not work under the instrument or place
anything underneath.
●The feet can break if they are overloaded. The overall load on the fol-
ded-out feet must not exceed 500 N.
Putting into Operation

Preparing for Use
R&S®SMB100B
16Getting Started 1422.1045.02 ─ 01
Risk of injury when stacking instruments
A stack of instruments can tilt over and cause injury if not stacked correctly.
Furthermore, the instruments at the bottom of the stack can be damaged
due to the load imposed by the instruments on top.
Observe the following instructions when stacking instruments:
●Never stack more than three instruments. If you need to stack more
than three instruments, install them in a rack.
●The overall load imposed on the lowest instrument must not exceed
500 N.
●It is best if all instruments have the same dimensions (width and length).
If you need to stack smaller instruments on the top, the overall load
imposed on the lowest instrument must not exceed 250 N.
●If the instruments have foldable feet, fold them in completely.
Mounting in a rack
The R&S SMB100B can be installed in a rack using a rack adapter kit (Order No.
see data sheet). The installation instructions are part of the adapter kit.
Putting into Operation

Preparing for Use
R&S®SMB100B
17Getting Started 1422.1045.02 ─ 01
Risk of instrument damage due to insufficient airflow in a rack
If the instrument is run with insufficient airflow for a longer period, the instru-
ment overheats, which can disturb the operation and even cause damage.
Make sure that all fan openings are unobstructed, that the airflow perfora-
tions are unimpeded, and that the minimum distance from the wall is 10 cm.
3.1.5 Connecting AC Power
The R&S SMB100B is equipped with an AC power supply connector, that can be
operated with different AC power voltages. Once it is connected, the instrument
automatically adjusts to the given voltage. Refer to the data sheet for the require-
ments of voltage and frequency. There is no need to set the voltage manually or
change fuses.
The AC supply and power switch is at the rear of the unit.
To connect the AC supply
► Connect the R&S SMB100B to the AC power source using the supplied power
cable.
Note: Since the instrument is designed in compliance with standard EN
61010-1 safety class I, it must only be connected to an outlet that has a
ground contact.
Characteristics of the AC power supply:
●100 V to 240 V AC
●50 Hz to 60 Hz; 400 Hz
●Max 2.1 A
3.1.6 Turning the Instrument On and Off
To turn on the R&S SMB100B
1. Connect the instrument to the AC supply.
Putting into Operation

Preparing for Use
R&S®SMB100B
18Getting Started 1422.1045.02 ─ 01
2. Turn on the main AC power switch at the rear panel of the R&S SMB100B
(position "I" (on)).
The instrument is supplied with AC power.
Warm-up time for OCXO
When the instrument is switched on, the OCXO requires an extended
warm-up time (see data sheet).
To start the R&S SMB100B
Starting the R&S SMB100B requires that it is connected and turned on.
► At the front panel, press the [On/Standby] key briefly.
The instrument boots the operating system and starts the instrument firmware.
After booting, the instrument is in the state before the last power off (standby
or ready), indicated by the color of the [On/Standby] key's LEDs:
● Green: the R&S SMB100B is running and ready for operation.
All modules are power-supplied.
● Orange: the R&S SMB100B is in standby mode (main AC power switch is
in position "I").
The standby power mode keeps the power switch circuits and the oven-
controlled crystal oscillator OCXO active. In this state, it is safe to switch
off the AC power and disconnect the instrument from the power supply.
To switch between standby and ready state, briefly press the [On/Standby]
key.
If a previous session was terminated regularly, the instrument uses the last setup
with the relevant instrument settings.
► To set up a new configuration, press the [Preset] key to return the instrument
to its defined reset/preset state.
Putting into Operation