Rola TMX Series User manual

Issue A
19/11/09
143 page 1 of 2
JEEP
Cherokee 5 door 4WD 04/94 - 07/99
TMX056
CARRYING CAPACITY 80 kg
BOLT
COVER
MOUNT PAD
(RIGHT) MOUNT PAD
(LEFT) SECURITY
BOLT
x2 x2 x4
REPRESENTATIVE
ONLY
REPRESENTATIVE
ONLY
x4
x2 x2 x2 x2
x2
x4 x4 x4 x4 x8 x1
x2
END SUPPORT
(RIGHT) TRACK CAP (CLOSED)
END SUPPORT
(LEFT) TRACK CAP (OPEN) TRACK EXTRUSION SNAP-ON COVER SECURITY COVER HEX NUT SCREW RIVETS SECURITY BOLT ASSEMBLY KEY CROSS-BAR ASSEMBLY
LENGTH
VARIES WITH
Please Note: You will require the following tools
Rubber Mallet Safety Knife Lead Pencil Tape Measure
Phillips Head Screwdriver
SOME FITMENTS
MAY ALSO
FEATURE THE
FOLLOWING
COMPONENTS:
Rivet Gun
ALTERNATIVE COVER
REMOVING THE EXISTING RACK ASSEMBLY
1. Locate the 12 xing screws which hold the two existing longitudinal tracks to
the vehicle roof and unscrew with a torx screwdriver. Retain screws as they are
used to x the ROLA track in place.
2. Lift o the existing rack assembly to reveal 12 threaded xing points in the
roof.
ASSEMBLY OF CROSS-BARS
3. Ensure the roof is clean, free from dust and grease.
4. Insert the neck of the End-Support into the void of the Cross-bar prole.
They are designed to be a tight t: use a rubber mallet if necessary (Fig.1)
5. Pull back the rubber Buer Strip about 20mm until the screw hole can be
accessed.(Fig. 2) Using a Phillips Head Screwdriver, fasten the screw through the
cross-bar and into the End Support. Do this for all four sides and replace the
buer strip.
NOTE: The longer cross-bars are to be tted to the front of the vehicle.
Check labelling on the underside of the cross-bar.
FITTING CROSS-BARS TO VEHICLE - REFER TO FIG. 3
6. Place both ROLA tracks on a clean bench.
7. Slide the tie downs to the centre of the tracks making sure the bottome face
of the tie down is engaged under the track lip.
8. Slide the large brass nut into the track and secure the tie down to the track
using the special bolt.
9. Remove the Adhesive Backing Tape from the underside of the Tracks and
place the tracks onto the vehilce roof ensuring alignment of xed points in roof
and hole in tracks.
10. Slide on large brass nut about 100mm from each end of the tracks.
11. Sandwich a closed end cap between the forward end of the tracks and the
roof xing point; then sandwick an open end cap between the rear of the tracks
and the roof xing point.
12. Fix the tracks to the roof using the torx screws from section on (Start from
the centre of the tracks and work to the ends ensuring the end caps are still in
place).
13. Place the crossbars onto the tracks with the sloping face of the end support
facing forward.
14. Align the hole in the end support with the large brass nut which was
previously slipping into the track. Loosely t the special bolt into the nut.
15. Fit each end support in the same manner.
16. Gradually tighten the special bolts alternately until even tensioning is
achieved and the end supports are xed.
PLEASE NOTE: Do not overtighten the bolts.
17. You are now ready to mount your accessory set onto the cross-bars using the
Global Mount Channel. Once installed, insert the ‘Global Channel’ Covers into the
End Supports. You have a choice of 2 - (a) quick access snap-on cover or (b) long
term mounting - security cover to cap o and lock the mount channel. (Fig. 4)
FINAL CHECK
Ensure that Cross-bars are parallel and square to the front and rear axis of the
vehicle. After loading, check bolt tightness and ensure that Locking Straps are
correctly engaged to the vehicle.
Number of rivets is
dependent on the
length of the track.
Generally there should
be 1 rivet for every hole
in the track. FRONT OF VEHICLE.
Open-Ended Track
Cap should be at the
rear of the vehicle .
Hex Nut
Quick Access
Snap-on Cover
Fig. 1
Fig. 3
Fig. 4
Fig. 2
Screw hole
Screw
Silicone Adhesive
Sealant
Security
Cover
CAUTION:
When installing this roof rack ensure the rivets do not damage or inhibit the
eective use of Curtain Airbags. If you are in any doubt regarding the installation
of this roof rack, please consult with your vehicle manufacturer or Rola Dealer.
TMX Series Roof Racks
Track
Track Lip
Bottom Face
Foam Seal
Tie Down Slide

page 2 of 2
RMX, PMX, TMX, TBX Series Roof Racks
RBX
For full warranty information, visit our website: www.rola.com.au
General Usage Information
Warnings
APPENDICES & ADDITIONAL ‘FITMENT SPECIFIC’ FITTING STEPS - IF REQUIRED
INSERTING COVERS
This area has been intentionally left blank.
It is essential for the proper assembly, operation and use of the Roof Rack that the instructions and safety precautions
supplied are strictly observed. Read any fitting, care and usage instruction carefully.
The maximum permissible load for your Roof Bar is the lower of the maximum load capacity specified in your vehicle opera-
tion manual, or specified as applying to the Roof-Rack. Do not exceed the maximum specified load capacity.
Maximum permissible load = weight of the Roof Rack + weight of accessories + weight of load (cargo).
When fitting the Roof-Rack and transporting a load, ensure the vehicle’s functions are not impaired (eg, sunroof, aerials,
windscreen wipers, mirrors). Rear doors on Hatch- and Wagon-type vehicles should be inspected for adequate clearance for
full opening operation of the boot/tailgate.
Stop and check all screw connections, bolts and retaining straps after a short distance of travel. Repeat these checks at regular
intervals.
Remember that the fitting of a Roof Rack and the transport of a load increases the overall height of the carrying vehicle.
Where the Roof-Rack is to be used in off-road conditions, a safety weight reduction of 1.5 should be observed from the total
carrying capacity. (eg. 60kg becomes 40kg)
Cequent will not be liable to the purchaser or any other person for any consequential, incidental, direct or indirect loss,
damage or costs incurred of suffered by the purchaser or any other person including but not limited to damage to persons or
property, loss of turnover, loss of profits, loss of business or goodwill, arising from or in relation to the assembly and use of the
Roof rack, or the non-observance of the fitting and care instructions.