Roland TrueVIS VG-640 User manual

Thank you very much for purchasing this product.
To ensure correct and safe usage with a full understanding of this product's performance, please be sure to read through
this manual completely and store it in a safe location.
Unauthorized copying or transferral, in whole or in part, of this manual is prohibited.
The contents of this manual and the specications of this product are subject to change without notice.
This manual and the product have been prepared and tested as much as possible. If you nd any misprints or errors,
please inform Roland DG Corp.
Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage that may occur through use of this
product, regardless of any failure to perform on the part of this product.
Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage that may occur with respect to any
article made using this product.
USER'S MANUAL
R1-151209
This is an inductive reading/writing device that uses radio waves (an RFID device).
• RFID is used to read the information inscribed on the ink pouches (or cartridges).
• If you use a pacemaker or other implanted medical equipment, do not approach this machine.
• Do not use this machine within hospitals.

This product uses GNU General Public License (GPL)/GNU Lesser General Public License (LGPL) software.You have
the right to acquire, modify, and distribute the source code for this GPL/LGPL software. You can obtain the GPL/
LGPL source code used in this product by downloading it from the following website:
http://www.rolanddg.com/gpl/
Roland DG Corp. has licensed the MMP technology from the TPL Group.
Copyright (c) 2012 - 2013, Murata Manufacturing Co., Ltd. All rights reserved.
Redistribution and use in source and binary forms, with or without modication, are permitted provided that
the following conditions are met:
-Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials provided with the distribution.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS
OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR
CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY
WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
For the USA and Canada
FCC CAUTION
Changes or modications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
This device complies with Part 15 of FCC Rules and Industry Canada’s licence-exempt RSSs. Operation is
subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.
------
Le présent appareil est conforme à la partie 15 des règles de la FCC et aux normes des CNR d'Indus-
trie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes : (1)l'appareil ne doit pas produire de brouillage, et (2) l'appareil doit accept-
er tout brouillage subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets
theFCCradiofrequency (RF)ExposureGuidelines andRSS-102 oftheIC radiofrequency(RF) Exposurerules.Thisequip-
menthasverylowlevelsofRFenergythatisdeemedtocomplywithoutmaximumpermissiveexposureevaluation(MPE).
------
Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non
contrôlé et respecte les règles les radioélectriques (RF) de la FCC lignes directrices d'exposition et d’exposition
aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une énergie RF très faible qui est
considérée comme conforme sans évaluation de l’exposition maximale autorisée (MPE).

1
Contents
Contents.......................................................................................................................1
Chapter 1 Machine Highlights ...........................................................................................5
Part Names and Functions...........................................................................................6
Printer Unit................................................................................................................................................................ 6
Operation Panel ....................................................................................................................................................11
Warning Labels................................................................................................................................................12
Vignettes d'avertissement ..........................................................................................................................13
Menu List....................................................................................................................14
Main Menu..............................................................................................................................................................14
Function Menu ......................................................................................................................................................18
Language and Unit Menu..................................................................................................................................19
Important Notes on Handling and Use .......................................................................20
Printer Unit..............................................................................................................................................................20
Ink Pouches.............................................................................................................................................................21
Chapter 2 Basic Operation...............................................................................................23
Power Supply Operations ..........................................................................................24
Turning the Power On.........................................................................................................................................24
Turning the Power O ........................................................................................................................................25
Precautions When Operating the Power Supply.......................................................................................26
Sleep Mode (Power-saving Feature)..............................................................................................................26
About the Media Used................................................................................................27
Types of Media ......................................................................................................................................................27
Conditions for Usable Media............................................................................................................................27
Basic Printing Method ................................................................................................28
Printing Flow..........................................................................................................................................................28
Step 1 : Loading Roll Media (Setup of Media)............................................................................................29
Step 2 : Initial Adjustment (Correcting for Misalignment in Bidirectional Printing) ....................37
Step 3 : Batch Settings........................................................................................................................................39
Step 4 : Setting the Base Point.........................................................................................................................53
Step 5 : Printing Tests and Normal Cleaning ..............................................................................................54
Step 6 : Starting Output .....................................................................................................................................57
Basic Settings for Cutting...........................................................................................59
Hints and Tips for Cutting Settings ................................................................................................................59
Important Note on Cutting...............................................................................................................................59
Preventing Pulling of the Media with Undue Force.................................................................................60
Setting the Cutting Test and the Blade Force.............................................................................................61
Printing and Cutting with Crop Marks.........................................................................63
What Is Printing and Cutting with Crop Marks? ........................................................................................63
How to Print and Cut with Crop Marks.........................................................................................................64
Printing and Cutting with Crop Marks: Basic Troubleshooting............................................................66
Ink Pouch/Cleaning Liquid Pouch Replacement ........................................................67
Out-of-ink Warnings............................................................................................................................................67
Ink Pouch Replacement .....................................................................................................................................68
Cleaning Liquid Pouch Replacement............................................................................................................70
Other Basic Operations..............................................................................................72
Loading Sheet Media (Setup of Media)........................................................................................................72
Pausing or Canceling Output...........................................................................................................................77
Cutting O the Media.........................................................................................................................................77

Contents
2
Chapter 3 Maintenance ....................................................................................................79
Daily Maintenance......................................................................................................80
Cleaning...................................................................................................................................................................80
When "EMPTY DRAIN BOTTLE" Is Displayed...............................................................................................81
Disposing of Discharged Fluid.........................................................................................................................82
Timing of Print Head Care and Maintenance .............................................................................................84
When Normal Cleaning Is Not Effective.....................................................................85
Medium/Powerful Cleaning .............................................................................................................................85
Monthly Cleaning .......................................................................................................87
Manual Cleaning...................................................................................................................................................87
If Colors Are Uneven ..................................................................................................94
Mixing the Ink by Shaking the Pouch Tray ..................................................................................................94
If Colors Are Still Uneven ...................................................................................................................................94
When Dot Drop-outs/Uneven Colors Are Not Fixed...................................................95
Super Cleaning......................................................................................................................................................95
Replacing Consumable Parts.....................................................................................99
Replacing the Wiper ............................................................................................................................................99
Cleaning the Wiper Tray and Replacing the Tray Pads ......................................................................... 102
Replacing the Blade.......................................................................................................................................... 106
Replacing the Separating Knife.................................................................................................................... 109
When Not in Use for a Prolonged Period .................................................................112
Keep Performing Maintenance .................................................................................................................... 112
Disposing of Discharged Fluid...................................................................................................................... 112
Chapter 4 Advanced Functions .....................................................................................113
Using Presets...........................................................................................................114
Saving the Current Settings (Preset Saving)............................................................................................ 114
Loading a Saved Preset ................................................................................................................................... 116
Settings for the Media Heating System....................................................................117
What Is the Media Heating System?........................................................................................................... 117
Making the Temperature Setting for the Media Heating System .................................................... 118
Setting the Temperature during Preheating ........................................................................................... 119
Drying the Trailing Edge of the Printing Area on the Dryer............................................................... 120
Setting the Drying Time after Printing....................................................................................................... 121
Using an Optional Dryer ................................................................................................................................. 122
Using a Blower-fan Unit .................................................................................................................................. 123
Correction Functions ................................................................................................124
Correcting for Misalignment in Bidirectional Printing......................................................................... 124
Correcting for Misalignment in Bidirectional Printing More Precisely........................................... 125
Alleviating Horizontal Bands (Feed Correction Function) .................................................................. 126
Conguring Settings to Match the Properties of the Media......................................128
Adjusting Print Head Height to Match Media Thickness .................................................................... 128
Using Transparent Media................................................................................................................................ 129
Using Hard-to-dry Media................................................................................................................................ 130
Using Media That Wrinkles Easily/Does Not Move Smoothly............................................................ 131
Speeding Up Output for Narrow Media.................................................................................................... 132
Preventing Soiling of the Media and Dot Drop-Out............................................................................. 133
Using Sticky Media............................................................................................................................................ 134
Advanced Cutting Settings.......................................................................................135

Contents
3
Fine-tuning the Cutting Conditions ........................................................................................................... 135
Accurately Adjusting the Cutting-in Amount ......................................................................................... 137
Performing Distance Correction During Cutting................................................................................... 138
Correcting the Misalignment of the Printing and Cutting Positions.............................................. 139
Prioritizing the Cutting Settings of This Machine over the Software RIP Settings..................... 142
Viewing the Automatic Environment Correction Function Settings.............................................. 143
Correcting the Misalignment of the Printing and Cutting Positions during Cutting ............... 144
Advanced Settings for Printing and Cutting with Crop Marks ..................................146
Aligning Positions Manually.......................................................................................................................... 146
Correcting Misalignment for Printing and Cutting When Using Crop Marks .............................. 148
Using Media Take-Up System..................................................................................151
About Media Take-Up System....................................................................................................................... 151
Performing Operations from Roland DG Mobile Panel ............................................152
What Is Roland DG Mobile Panel? ............................................................................................................... 152
Downloading Mobile Panel........................................................................................................................... 152
Using Mobile Panel........................................................................................................................................... 153
Important Notes on Using Mobile Panel .................................................................................................. 153
Other Useful Functions ............................................................................................155
Using the Print Light (Interior Light)........................................................................................................... 155
Performing Printing Tests Arranged Horizontally.................................................................................. 155
Using Media Flanges for Paper Tubes (Cores) with an Internal Diameter of 2 Inches .............. 156
Chapter 5 Administrator Menu ......................................................................................157
Output Operation Management................................................................................158
Printing a System Report ................................................................................................................................ 158
Determining What Happens When Ink Runs Out ................................................................................. 158
Displaying the Amount of Media Remaining.......................................................................................... 159
Making Sure to Verify the Setting for the Amount Remaining Every Time the Media Is Changed...........160
Printing the Amount of Remaining Media............................................................................................... 161
System Management of Printer................................................................................163
Setting the Menu Language and the Units of Measurement............................................................ 163
Turning on Bluetooth Communication ..................................................................................................... 163
Setting the Activation Interval for Sleep Mode (Power-saving Feature)....................................... 165
Viewing System Information......................................................................................................................... 166
Returning All Settings to Their Factory Default Values........................................................................ 167
When Moving the Unit..............................................................................................168
Procedure from Preparing to Move to Reinstallation........................................................................... 168
Chapter 6 Troubleshooting ............................................................................................171
Attractive Printing or Cutting Is Impossible ..............................................................172
Printed Results Are Coarse or Contain Horizontal Stripes .................................................................. 172
The Media Becomes Soiled When Printed................................................................................................ 173
Colors Are Unstable or Uneven .................................................................................................................... 174
Cutting Is Misaligned or Skewed ................................................................................................................. 175
A Media Jam Occurs ................................................................................................176
The Media Has Jammed.................................................................................................................................. 176
Media Feed Is Not Smooth ......................................................................................177
Media Wrinkles or Shrinks .............................................................................................................................. 177
Media Feed Is Not Straight............................................................................................................................. 178

Contents
4
Media Feed Is Not Smooth............................................................................................................................. 178
Print Heads Stop Moving .........................................................................................179
What to Do First ................................................................................................................................................. 179
If the Print Heads Still Do Not Move ........................................................................................................... 179
Other Problems ........................................................................................................181
The Printer Unit Doesn't Run......................................................................................................................... 181
The Media Heating System Doesn't Warm Up........................................................................................ 182
Cannot Cut O the Media .............................................................................................................................. 182
It Is not Possible to Check the Amount of Discharged Fluid in the Drain Bottle........................ 183
Printer Cannot Be Operated from Mobile Panel..................................................................................... 183
A Message Appears .................................................................................................185
An Error Message Appears ......................................................................................187
Chapter 7 Appendix ........................................................................................................191
Printing Area.............................................................................................................192
Maximum Area................................................................................................................................................... 192
Maximum Area When Using Crop Marks.................................................................................................. 192
The Media-Cuto Location During Continuous Printing.................................................................... 193
About the Blade........................................................................................................194
Locations of the Power Rating and Serial Number Labels.......................................195
Specications ...........................................................................................................196
Copyright © 2015 Roland DG Corporation
http://www.rolanddg.com/
Android™, Google Play™ are the trademarks or the registered trademarks of Google Inc..
iPhone, App Store, iTunes are the trademarks or the registered trademarks of Apple Inc. registered in the U.S. and other
countries.
Company names and product names are trademarks or registered trademarks of their respective holders.

1
Machine Highlights
Chapter 1 Machine Highlights
Part Names and Functions ..........................................................................................6
Printer Unit................................................................................................................... 6
Operation Panel..........................................................................................................11
Warning Labels .................................................................................................... 12
Vignettes d'avertissement.................................................................................... 13
Menu List ...................................................................................................................14
Main Menu................................................................................................................. 14
Function Menu........................................................................................................... 18
Language and Unit Menu .......................................................................................... 19
Important Notes on Handling and Use.......................................................................20
Printer Unit................................................................................................................. 20
Ink Pouches............................................................................................................... 21
5

6
1
Machine Highlights
1
Machine Highlights
Printer Unit
Front
No. Name Function overview
1Ink slot cover, ink slots
Open this cover to access the slots in which the
ink trays are inserted. Leave this closed except
when switching ink trays.
2Front cover
Open this when necessary, such as when load-
ing media. In all other situations, keep the front
cover closed.
3Loading lever (front) Operate this when you load media.
4Panel cover, operation panel
Open this cover to access the operation panel.
Use the operation panel to operate this machine.
"P. 11 "Operation Panel"
5Left cover Open this when you perform maintenance.
6Right cover Open this when you perform maintenance.
7Drain bottle Discharged uid is stored in this bottle.
Part Names and Functions

Part Names and Functions
1
Machine Highlights
7
Rear
No. Name Function overview
1Main power switch Switch the main power on/o.
2Power-cord connector Use this to connect the power cable.
3Loading lever (rear) Operate this when you load media.
4Media holders Use these when you load media.
5Shafts Use these when you load media.
Side
No. Name Function overview
1Cleaning liquid tray slot Insert the tray with the cleaning liquid pouch
into this slot.
2Ethernet connector Use this to connect an Ethernet cable.

Part Names and Functions
1
Machine Highlights
8
Front Cover Interior/Print Head Area
No. Name Function overview
1Print light
This light illuminates the front cover interior. This
makes it easier to see the printing status. It ashes
in red if a serious error occurs.
"P. 9 "Serious Errors Indicated by the Print
Light"
2Print-head carriage The print heads are inside here.
3Cutting carriage
The blade and the separating knife are inside here.
4Grit rollers These rollers feed the media.
5Pinch rollers
(left pinch roller, right pinch roller,
and middle pinch roller)
These clamp the media when the loading lever is
lowered.The rollers are called the left pinch roller,
the right pinch roller, and the middle pinch roller
according to their positions.

Part Names and Functions
1
Machine Highlights
9
No. Name Function overview
6Media clamp
This clamps the edge of the media to keep it from
coming loose. It also prevents fuzz on the cut
edge of the media from touching the print heads.
7Grit patterns
These indicate the locations of the grit rollers.When
loading media, be sure to place the pinch rollers
within the ranges indicated by these patterns.
8Blade protector This is the path that the blade takes during cut-
ting. It protects the tip of the blade.
9Platen
This is the path over which the media passes. A suc-
tion fan that keeps the media from coming loose
and a print heater that helps x the ink are built in.
0Apron
This has a built-in dryer to speed up drying of the ink.
⑪Wiper Cleans the print heads during automatic cleaning
and in similar situations.
BWiper tray This tray houses the wiper cleaning liquid used
to clean the wiper. It contains three tray pads.
CWaste valve Open this valve to drain the discharged uid that
has collected in the wiper tray.
Serious Errors Indicated by the Print Light
If an error that may lead to serious damage to the printer occurs, the print light blinks in red.
This indicates one of the situations shown below.
When the print light blinks in red, the error also appears on the operation panel's display screen. Check the
display screen, and then respond to the error according to the information in P. 187 "An Error Message Ap-
pears" in this manual.
Display screen Error overview
AVOIDING DRY-UP TURN POW-
ER OFF
The print heads were about to dry out. The print heads may be dam-
aged if allowed to dry out.
MOTOR ERROR TURN POWER
OFF
An excessive load was applied to the motor. If this error is not ad-
dressed, the print heads may be damaged.
TEMPERATURE IS TOO LOW
**°C
The ambient temperature in the printer's installation location has
fallen below the temperature in which operation is possible. If this
error is not addressed, the printer may malfunction.
TEMPERATURE IS TOO HIGH
**°C
The ambient temperature in the printer's installation location has risen
above the temperature in which operation is possible. If this error is
not addressed, the printer may malfunction.
CANCELED FOR PUMP PRO-
TECTION
An excessive load was applied to the pump within the machine. If this
error is not addressed, the pump may malfunction.
SERVICE CALL xxxx An unrecoverable error or an error that requires a part replacement
has occurred.

Part Names and Functions
1
Machine Highlights
10
If a Cover Opens during Operation
If the front cover, left cover, or right cover (hereinafter referred to as "cover") opens during an operation in
which the print-head carriage moves such as printing or cutting, the machine makes an emergency stop.
When an emergency stop occurs, a message prompting you to close the cover will be displayed on the screen.
Follow the instruction shown on the screen and close the cover.
After you close the cover, the following message appears on the screen. Follow the instruction shown on
the screen and press [ENTER]. The machine recovers from the error and is then able to continue operations."
PRESS THE ENTER
KEY TO CONTINUE
If the message shown above does not appear even after you close the cover, a nonrecoverable error may have
occurred. Refer to P. 187 "An Error Message Appears".

Part Names and Functions
1
Machine Highlights
11
Operation Panel
Part Name Description Notation in this manual
Display screen This displays various setting menus and
other information.
Sub power switch
This switches the printer on and o. (To
switch the printer o, hold down the
switch for one second or longer). The
light ashes slowly when the machine
is in sleep mode.
ENTER ENTER key Use this for such tasks as enabling set-
ting values. [ENTER]
MENU MENU key Press this to enter the menus for various
settings. [MENU]
FUNCTION FUNCTION key
Press this when entering the setting
menu for cleaning of the print heads,
printing tests, and so on.
[FUNCTION]
PAUSE PAUSE key This pauses the printing operation. It
lights when operation is paused. [PAUSE]
Cursor keys
Use these to select settings for menu
items, to move the media, and for other
such operations.
[] [ ] [ ] [ ]
BUSY BUSY light This lights during printing and other
such operations. [BUSY]
SETUP SETUP light This lights when media has been loaded
correctly. [SETUP]
BASE BASE POINT light This lights when the base point (the
output-start location) has been set. [BASE]
HEATER HEATER light
This ashes while the media heating
system is warming up. It stays lit when
the set temperature is reached.
[HEATER]
W1200mm

Part Names and Functions
1
Machine Highlights
12
Warning Labels
Warning labels are axed to the machine to make areas of danger immediately clear. The meanings of these
labels are as follows. Be sure to heed their warnings. Also, never remove the labels or allow them to become dirty.
Ink, cleaning liquid, and discharged uid are toxic
If these uids come into contact with the eyes or skin,
it may be hazardous to the health. When performing
maintenance work, for example when disposing of dis-
charged uid, wear protective eyewear and protective
gloves (refer to the safety data sheet (SDS)).
Caution: Pinching Hazard
Be careful not to allow the
ngers to become pinched
when closing covers.
Caution: High Temperature
The platen and dryer become
hot. Exercise caution to avoid
re or burns.
Flammable
Ink and discharged uid are ammable.
Keep away from open ame.
Caution: High Voltage
Removing the cover may result in
high-voltage electric shock.

Part Names and Functions
1
Machine Highlights
13
Vignettes d'avertissement
Des vignettes d'avertissement sont apposées pour qu'il soit facile de repérer les zones dangereuses. La sig-
nication des vignettes est donnée ci-dessous. Respecter les avertissements. Ne jamais retirer les vignettes
et ne pas les laisser s'encrasser.
L’encre, le liquide de nettoyage et le rejet
liquide sont toxiques
Il peut s’avérer dangereux pour la santé si ces
liquides viennent en contact avec les yeux ou
la peau. Lors de travaux d’entretien, à l’élimi-
nation de rejets liquides par exemple, utilisez
une protection oculaire et des gants protec-
teurs (se reporter à la che signalétique [FS]).
Attention : Risque de pincement
Faire attention de ne pas coincer les
doigts pendant le chargement du support
ou lors de la fermeture du couvercle.
Attention : Température
élevée
La platine et la surface de
séchage chauffent. Être pru-
dent pour éviter un incendie
ou des brûlures.
Inammable
L'encre et les liquides usés sont
inammables. Les garder loin de toute
amme nue.
Attention : voltage élevé
Il peut être dangereux de retirer le couvercle puis-
qu’il y aurait des risques de chocs électriques ou
d’électrocution à cause du voltage élevé.

14
1
Machine Highlights
1
Machine Highlights
Menu List
Main Menu
To the [TEST PRINT] menu
To the [LOAD] menu
To the [CUTTING MENU] menu
To the [TEST PRINT] menu
To the [TEST PRINT] menu
To the [NAME8] menu
To the [NAME1] menu
メニュー
ﾒﾃﾞｨｱ ｾｯﾃｨﾝｸﾞ
MENU
MEDIA SETTING
MENU
ADJUST BI-DIR.
MENU
CALIBRATION
MENU
HEAD HEIGHT
PRESET
LOAD
LOAD
NAME1
LOAD
NAME8
SAVE
NAME1
PRESET
SAVE
ADJUST BI-DIR.
TEST PRINT
ADJUST BI-DIR.
SIMPLE SETTING
ADJUST BI-DIR.
DETAIL SETTING
CALIBRATION
TEST PRINT
CALIBRATION
SETTING
HEAD HEIGHT
HIGH Low
SET NAME
SAVE
NAME8
SIMPLE SETTING
2 1
DETAIL SETTING
TEST PRINT
DETAIL SETTING
SETTING NO.1
H1 H2 H3
0 0 0２
H4
0
H1 H2 H3
0 0 0
H4
0
DETAIL SETTING
SETTING NO.2
SETTING
0.00％ +0.05％
SET NAME
NAME8
MENU
PRESET
Continue
To the [SETTING] menu
To the [SAVE] menu
To the [DETAIL SETTING] menu
To the [NAME8] menu
To the [NAME1] menu
To the [SETTING NO.2] menu
Press

Menu List
1
Machine Highlights
15
To the [NONE] menu
To the [SUPER CL.] menu
To the [EMPTY MODE] menu
To the [TEST PRINT POS] menu
To the [INTERVAL(TIME)] menu
SUB MENU
EDGE DETECTIONプ
MENU
SUB MENU
SUB MENU
MEDIA RELEASE
SUB MENU
FACTORY DEFAULT
SUB MENU
SLEEP
SUB MENU
SYSTEM REPORT
SUB MENU
INK CONTROL
EDGE DETECTIONプ
ENABLE ENABLE
SUB MENU
SCAN INTERVAL
SCAN INTERVAL
OFF 1.0sec
SUB MENU
VACUUM POWER
VACUUM POWER
AUTO 90%
SUB MENU
FULL WIDTH S
FULL WIDTH S
FULL OFF
SUB MENU
PERIODIC CL.
PERIODIC CL.
NONE
PERIODIC CL.
PAGE
PERIODIC CL.
INTERVAL(JOB)
INTERVAL(JOB)
10min 990min
INTERVAL(TIME)
10min 990min
INTERVAL
15min 15min
SUPER CL.
AB
PERIODIC CL.
INTERVAL(TIME)
MEDIA RELEASE
DISABLE ENABLE
SLEEP
INTERVAL
INK CONTROL
EMPTY MODE
EMPTY MODE
STOP CONT.
INK CONTROL
SUPER CL.
Continue
Continue ContinueContinue

Menu List
1
Machine Highlights
16
SUB MENU
MAINTENANCE
SUB MENU
TEST PRINT POS
MAINTENANCE
REPLACE WIPER
MAINTENANCE
REPLACE KNIFE
MAINTENANCE
TRAY CLEANING
MAINTENANCE
DRAIN BOTTLE
TEST PRINT POS
SCAN FEED
SYSTEM INFO.
MODEL
MENU
SYSTEM INFO.
MENU
HEATER MENU
MODEL
XX-XXXX
SYSTEM INFO.
SERIAL NO.
SERIAL NO.
XXXXXXX
SYSTEM INFO.
INK
INK
XXXXXXXX XXXX
SYSTEM INFO.
FIRMWARE
FIRMWARE
Ver. X.XX
SYSTEM INFO.
NETWORK
SYSTEM INFO.
BLUETOOTH
IP ADDRESS
255.255.255.255
IP ADDRESS
255.255.255.255
SUBNET MASK
255.255.255.255
SUBNET MASK
255.255.255.255
GATEWAY ADDR.
255.255.255.255
GATEWAY ADDR.
255.255.255.255
BLUETOOTH
DISABLE
BLUETOOTH
DISABLE ENABLE
HEATER MENU
FEED FOR DRY
FEED FOR DRY
DISABLE ENABLE
HEATER MENU
PREHEATING
PREHEATING
30゜C MENU
HEATER MENU
OPTION DRYER
OPTION DRYER
DISABLE ENABLE
HEATER MENU
BLOWER FAN
BLOWER FAN
DISABLE ENABLE
HEATER MENU
DRYING TIME
DRYING TIME
10min 10min
MAC ADDRESS
XXXXXXXXXXXX
NETWORK
IP ADDRESS
NETWORK
SUBNET MASK
NETWORK
GATEWAY ADDR.
NETWORK
MAC ADDRESS
Continue
Continue
Continue Continue
To the [DRAIN BOTTLE] menu
To the [MAC ADDRESS] menu
To the [REPLACE WIPER] menu
To the [SHEET TYPE] menu
To the [BLUETOOTH] menu
To the [IP ADDRESS] menu
To the [MODEL] menu
To the [DRYING TIME] menu
To the [FEED FOR DRY] menu

Menu List
1
Machine Highlights
17
To the [AUTO ENV.MATCH] menu
To the [MEDIA SETTING] menu
ｶｯﾃｨﾝｸﾞ ﾒﾆｭｰ
ｻｷｵｸﾘ
ｻｷｵｸﾘ
ﾑｺｳ ﾕｳｺｳ
ｶｯﾃｨﾝｸﾞ ﾒﾆｭｰ
ｶｯﾄｾｯﾃｲ ﾕｳｾﾝ
ｶｯﾄｾｯﾃｲ ﾕｳｾﾝ
ｺﾏﾝﾄﾞ ﾒﾆｭｰ
ｶｯﾃｨﾝｸﾞ ﾒﾆｭｰ
ｼﾞﾄﾞｳｶﾝｷｮｳﾎｾｲ
ｼﾞﾄﾞｳｶﾝｷｮｳﾎｾｲ
ﾑｺｳ ﾕｳｺｳ
MENU
INK REMAINING
MENU
SHEET REMAIN
MENU
CUTTING MENU
SHEET REMAIN
PRINT MEMO
SHEET REMAIN
SET LENGTH
SET LENGTH
0.0m 99.9m
SHEET REMAIN
AUTO DISPLAY
AUTO DISPLAY
DISABLE ENABLE
CUTTING MENU
PRINT-CUT ADJ.
CUTTING MENU
CROP-CUT ADJ.
CUTTING MENU
CALIBRATION
PRINT-CUT ADJ.
TEST PRINT
PRINT-CUT ADJ.
SETTING
PRINT-CUT ADJ.
TEST PRINT 2
CROP-CUT ADJ.
TEST PRINT
CROP-CUT ADJ.
SETTING
F:+0.30 +0.35mm
S:-0.40 -0.40mm
CALIBRATION
FEED SETTING
CUTTING MENU
PREFEED
PREFEED
DISABLE ENABLE
CUTTING MENU
CUTTING PRIOR
CUTTING PRIOR
COMMAND MENU
CUTTING MENU
AUTO ENV.MATCH
AUTO ENV.MATCH
DISABLE ENABLE
FEED SETTING
-0.10% -0.10%
CALIBRATION
SCAN SETTING
SCAN SETTING
-0.10% -0.10%
F:+0.30 +0.35mm
S:-0.40 -0.40mm
CROP-CUT ADJ.
TEST PRINT 2
To the [TEST PRINT 2] menu
To the [AUTO DISPLAY] menu
To the [TEST PRINT 2] menu
To the [TEST PRINT] menu
To the [SCAN SETTING] menu
To the [TEST PRINT] menu
To the [PRINT-CUT ADJ.] menu
1 2 3 4
5 6 7 8
Continue
To the [PRINT MEMO] menu
To the [FEED SETTING] menu

Menu List
1
Machine Highlights
18
Function Menu
(*1)
(*1) (*1)(*2)
(*1)
1
(*3)
To the [MANUAL CL.] menu
To the [TEST PRINT] menu
To the [TEST CUT] menu
To the [BASE POINT] menu
To the [PRINT ] menu
To the [PRINT-CUT ADJ.] menu
To the [DRYER] menu
CLEANING
NORMAL CL.
NORMAL CL.
AB
CLEANING
MEDIUM CL.
MEDIUM CL.
AB
CLEANING
POWERFUL CL.
POWERFUL CL.
AB
HEATER CONFIG
PRINT 40゜C
PRINT
40゜C 45゜C
HEATER CONFIG
DRYER 40゜C
CUT CONFIG
TEST CUT
DRYER
40゜C 45゜C
CUT CONFIG
FORCE
FORCE
50 gf 50 gf
CUT CONFIG
SPEED
SPEED
20 cm/s 20 cm/s
CUT CONFIG
OFFSET
OFFSET
0.250mm 0.250mm
CUT CONFIG
UP-SPEED
UP-SPEED
20 cm/s 20 cm/s
CUT CONFIG
PRINT-CUT ADJ.
F:+0.30 +0.35mm
S:-0.40 -0.40mm
PRINT LIGHT
AUTO OFF
FUNCTION
CLEANING
FUNCTION
CUT CONFIG
FUNCTION
PRINT LIGHT
FUNCTION
BASE POINT
BASE POINT
ALIGN POINT 1
CLEANING
TEST PRINT
CLEANING
MANUAL CL.
FUNCTION
HEATER CONFIG
FUNCTION
SHEET CUT
Press
〔To the [PRINT LIGHT] menu
(*1) This is displayed when the width of the media is displayed after the media has been loaded.
(*2) This is not displayed when base point is not set.
(*3) This is not displayed when [PAUSE] is not pressed.