rollease acmeda AUTOMATE Installation manual

AUTOMATE™
AC MECHANICAL LIMIT TUBULAR MOTOR
MECHANICAL
LIMIT
QUIET
OPERATION
FEATURES:
• Line Voltage (available for both 100V-120V & 220V-240V applications)
• “Slim Head” design minimizes light gap
• Low Operating Noise Levels.
• Adjustable Mechanical Limits
AUTOMATE™| mechanical limit AC motors come in 35mm and 45mm diameters with
various torque and speeds, including models with Quiet Operation. A “Slim Head” design
minimizes light gap.
MTACML_Automate _AC_INSTR_v2.0 AUGUST 2018

2 | Automate™Programming Instructions | AC Mechanical ROLLEASE ACMEDA
SAFETY INSTRUCTIONS
WARNING: Important safety instructions to be read before installation.
Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.
CAUTION
• Do not expose to moisture or extreme temperatures.
• Do not allow children to play with this device.
• Use or modification outside the scope of this instruction manual will void warranty.
• Installation and programming to be performed by a suitably qualified installer.
• For use within tubular blinds.
• Ensure correct crown and drive adapters are used for the intended system.
• Use only Rollease Acmeda hardware.
• Before installation, remove any unnecessary cords and disable any equipment not needed for powered operation.
• Ensure torque and operating time is compatible with end application.
• Do not expose the motor to water or install in humid or damp environments.
• Motor is to be installed in horizontal application only.
• Do not drill into motor body.
• The routing of cable through walls shall be protected by isolating bushes or grommets.
• Ensure power cable and aerial is clear and protected from moving parts.
• If cable or power connector is damaged do not use.
Important safety instructions to be read prior to operation.
• It is important for the safety of persons to follow the enclosed instructions. Save these instructions for future reference.
• Persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge
should not be allowed to use this product.
• Keep remote controls away from children.
• Frequently inspect for improper operation. Do not use if repair or adjustment is necessary.
• Keep motor away from acid and alkali.
• Do not force the motor drive.
• Keep clear when in operation.
5005833

3 | Automate™Programming Instructions | AC Mechanical ROLLEASE ACMEDA
CONTENTS
1 ASSEMBLY 4
2 WIRING 5
2.1 Power options 5
2.2 Check direction 5
3 ADJUST LIMITS 6
3.1 Adjust Upper Limit 6
3.2 Adjust Lower Limit 7
4 MOTOR OPERATION 8
5 TROUBLE SHOOTING 8

4 | Automate™Programming Instructions | AC Mechanical ROLLEASE ACMEDA
1 ASSEMBLY
Step 1. Cut roller tube to required length.
Step 2. Ensure roller tube is clean and free from
burrs.
Step 3. Fit required crown, drive and bracket adapters.
Tube must be close fitting with chosen crown
and drive adapters. Refer to Rollease Acmeda
System Assembly Manual for recommended
crown, drive, and bracket adapter kits.
Step 4. Slide Motor into tube.
Insert by aligning keyway in crown and
drive wheel to the tube.
Step 5. Mount motorized tube onto brackets.
Refer to Rollease Acmeda System
Assembly Manual for recommended
crown, drive, and bracket adapter kits.
NOTE: Two limit apertures, red and white, should
be orientated to users for easy limit
adjustment
Please refer to Rollease Acmeda System Assembly Manual for full assembly instructions relevant to the hardware system being used.
Crown
Drive
Retaining
Clip
Motor Head
Adapter
Bracket

5 | Automate™Programming Instructions | AC Mechanical ROLLEASE ACMEDA
2 WIRING
2.1 Power options
Ensure mains power supply is off if you are adjusting cables
During operation DO NOT turn on 2 switches at the same time
MOTOR Neutral Direction 1 Direction 2 Earth
RB24-4502-xxx003 Blue Black Brown Green/Yellow
MTACQML35-6
White Red Black Green
MTACML35-6
MTAC45-20-M
MTACQ45-10-M
Cut off the mains power supply
• Connect the motor accordingly
• Ensure cable is kept clear of fabric:
After connection, switch on the “UP” button and check the shade rotating direction. If the direction does not
follow the “UP” or “DOWN” mark, swap the brown and black or red and black wires to those two buttons.
NEUTRAL
Single - channel
mechanical switch
N L
LIVE
EARTH
2.2 Check Direction

6 | Automate™Programming Instructions | AC Mechanical ROLLEASE ACMEDA
3 ADJUST LIMITS
3.1 Adjust upper limit
Identify the right aperture for upper limit adjustment:
• Top aperture for upper limit adjustment if the shade moves upward with clockwise rotation viewed from
the right side of the shade.
• Bottom aperture for upper limit adjustment if the shade moves upward with anticlockwise rotation viewed
from the right side of the shade.
Adjust the upper limit:
• Insert a Motor Limit Adjuster into the right aperture. Turn it toward the “+” mark, the upper limit is
raised; turn it towards the “-” mark, the upper limit is lowered. Five revolutions of the adjuster’s rotation
make the upper limit adjust by one revolution of the tube.
Upper limit is lowered
+
-
-
+
BACK ROLL
Upper limit is lowered Upper limit is raised
Upper limit is raised
+
+-
- +
+-
-
+
+-
-+
+-
-
FRONT ROLL
+
-
-
+

7 | Automate™Programming Instructions | AC Mechanical ROLLEASE ACMEDA
Identify the right aperture for lower limit adjustment:
• Bottom aperture for lower limit adjustment if the shade moves upward with clockwise rotation viewed
from the right side of the shade.
• Top aperture for lower limit adjustment if the shade moves upward with anticlockwise rotation viewed
from the right side of the shade.
Adjust the lower limit:
• Insert a Motor Limit Adjuster into the right aperture. Turn it toward the “+” mark, the lower limit is
lowered; turn it towards the “-” mark, the upper limit is raised. Five revolutions of the adjuster’s rotation
make the lower limit adjust by one revolution of the tube.
3.2 Adjust lower limit
+
+-
-+
+-
-
+
+-
- +
+-
-
Lower limit is lowered
Lower limit is lowered
Lower limit is raised
Lower limit is raised
FRONT ROLL
BACK ROLL
-
+
+
-
-
+
+
-

8 | Automate™Programming Instructions | AC Mechanical
4 MOTOR OPERATION
5 TROUBLE SHOOTING
After setup, move the shade upward by continuously pressing the UP button; move the shade downward by
holding the DOWN button.
NOTE: Shade movement stops immediately if the button is released.
ROLLEASE ACMEDA
AUSTRALIA
110 Northcorp Boulevard,
Broadmeadows VIC 3047
T [phone] | F [phone]
ROLLEASE ACMEDA
USA
Level 7/750 East Main Street.
Stamford, CT 06902 USA
T [phone] | F [phone]
ROLLEASE ACMEDA
EUROPE
Via Conca Del Naviglio 18, Milan
(Lombardia) Italy
T [phone] | F [phone]
Queensland Branch
Unit 2/62 Borthwick Avenue,
Murarrie QLD 4172
[e-mail]
rolleaseacmeda.com
Problem Cause Remedy
Shade moves upward but the
DOWN button is pressed. Incorrect wire connection. Swap the black and brown/red and black wire inside the button.
After power is turned on, the
motor does not move or moves
slowly.
Low power voltage. Use the nominal power source.
Incorrect wire connection. Check and correct wire connection.
Overload.
Check the nominal load of the
motor and use the high torque
motor.
Installation problem. Reinstall the motor.
Motor’s movement suspends.
Rotation time is longer than 4
minutes and motor suspends due
to thermal protection.
Allow the motor to cool for 20
minutes. After cooling, the motor
should work normally.