rollease acmeda AUTOMATE User manual

AUTOMATE™CORE AND TILT MOTOR
INSTRUCTIONS
SOLAR OPTION
FAVORITE
POSITION
SELECTABLE
SPEED
ELECTRONIC
LIMIT
LEVEL CONTROL
433 MHZ
BI-DIRECTIONAL
PART NUMBER DESCRIPTION
MT01-4001-xxx002 Passthrough Tilt Motor Kit
MT01-4001-069003 AUTOMATE | VT TILT [12V/0.6Nm/11rpm]
• USE THIS DOCUMENT WITH THE FOLLOWING MOTORS:
AUTOMATE_TILT_PRGM_OCT_2023

2 | Automate™Programming Instructions | Tilt Motors ROLLEASE ACMEDA
SAFETY INSTRUCTIONS
WARNING: Important safety instructions to be read before installation.
Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.
CAUTION
• Do not expose to moisture or extreme temperatures.
• Do not allow children to play with this device.
• Use or modification outside the scope of this instruction manual will void warranty.
• Installation and programming to be performed by a suitably qualified installer.
• For use within tubular blinds.
• Ensure correct crown and drive adaptors are used for the intended system.
• Keep antenna straight and clear from metal objects
• Do not cut the antenna.
• Use only Rollease Acmeda hardware.
• Before installation, remove any unnecessary cords and disable any equipment not needed for powered operation.
• Ensure torque and operating time is compatible with end application.
• Do not expose the motor to water or install in humid or damp environments.
• Motor is to be installed in horizontal application only.
• Do not drill into motor body.
• The routing of cable through walls shall be protected by isolating bushes or grommets.
• Ensure power cable and aerial is clear and protected from moving parts.
• If cable or power connector is damaged do not use.
Important safety instructions to be read prior to operation.
• It is important for the safety of persons to follow the enclosed instructions. Save these instructions for future reference.
• Persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge
should not be allowed to use this product.
• Keep remote controls away from children.
• Frequently inspect for improper operation. Do not use if repair or adjustment is necessary.
• Keep motor away from acid and alkali.
• Do not force the motor drive.
• Keep clear when in operation.
Do not dispose of in general waste.
Please recycle batteries and damaged electrical products appropriately.

ROLLEASE ACMEDA Automate™Programming Instructions | Tilt Motors | 3
U.S. Radio Frequency FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician to help.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
ISED RSS Warning:
This device complies with Innovation, Science and Economic Development Canada license-exempt RSS standard(s). Operation
is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’ISED applicables aux appareils radio exemps de licence. L’exploitation est
autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, méme si le brouillage est susceptible d’en
compromettre le fonctionnement.
To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the
antenna of this device and persons during device operation.
To ensure compliance, operations at closer than this distance is not recommended.
Les antennes installées doivent être situées de facon à ce que la population ne puisse y être exposée à une distance de
moin de 20 cm. Installer les antennes de facon à ce que le personnel ne puisse approcher à 20 cm ou moins de la position
centrale de l’ antenne.
La FCC des éltats-unis stipule que cet appareil doit être en tout temps éloigné d’au moins 20 cm des personnes pendant
son functionnement.

4 | Automate™Programming Instructions | Tilt Motors ROLLEASE ACMEDA
CONTENTS
1 CORE TILT MOTOR ASSEMBLY 5
2 CORE TILT MOTOR WAND OPERATION 6
3 TILT MOTOR ASSEMBLY 7
4 WIRING 8
4.1 Power Options 8
5 P1 BUTTON FUNCTIONS 9
5.1 Motor state test 9
5.2 Motor configuration options 9
6 INITIAL SET UP 10
6.1 Pair motor with controller 10
6.2 Check motor direction 10
6.3 Set Limits 11
7 ADJUSTING LIMITS 12
7.1 Adjust upper limit 12
7.2 Adjust lower limit 12
8 CONTROLLERS AND CHANNELS 13
8.1 Using P2 Button on existing controller to add a new controller or channel 13
8.2 Using a pre-existing controller to add or delete a controller or channel 13
9 FAVORITE POSITIONING 14
9.1 Set a favorite position 14
9.2 Send shade to favorite position 14
9.3 Delete favorite position 14
10 TILT & ROLLER MODE 15
10.1 Toggle motor to Tilt Mode 15
10.2 Toggle Motor to Roller Mode 15
11 ADJUSTING SPEED 16
11.1 Increase Motor Speed 16
11.2 Decrease Motor Speed 16
12 SLEEP MODE 17
13 TROUBLE SHOOTING 18
NOTES 19

ROLLEASE ACMEDA Automate™Programming Instructions | Tilt Motors | 5
1 CORE TILT MOTOR ASSEMBLY
• Assemble correct
configuration as required
• Disassemble existing
venetian manual control
assembly
• Insert motor assembly into
existing venetian head rail
assembly
• Re-insert tilt rod through the
motor assembly & spools
• Attach switch control cover
Battery Charging

6 | Automate™Programming Instructions | Tilt Motors ROLLEASE ACMEDA
2 CORE TILT MOTOR WAND OPERATION
• Optional Control Wand

ROLLEASE ACMEDA Automate™Programming Instructions | Tilt Motors | 7
3 TILT MOTOR ASSEMBLY
• Assemble correct
configuration as required
• Insert motor assembly into
venetian head rail assembly
• Ensure tilt rod is engaged
with the motor
• Minimum tilt rod insertion
with motor is 1/2”
• Maximum tilt rod insertion
with motor is 3/4”
Battery Charging

8 | Automate™Programming Instructions | Tilt Motors ROLLEASE ACMEDA
4 WIRING
Ensure cable is kept clear of fabric.
Ensure antenna is kept straight and away from metal objects.
Automate DC TILT Motor is powered from a 12V DC power source. AA Battery wands, re-chargeable battery
packs with a variety of quick connect extension cords. For centralized installations, power supply range
can be extended with 18/2 wire (not available through Rollease Acmeda).
• During operation, if voltage drops to less than 10V, the motor will beep 10 times to indicate a power
supply issue.
• Motor will stop running when the voltage is lower than 7V and it will resume again when the voltage is
greater than 7.5V.
NOTE:
• Passthrough Tilt Motor MT01-4001-xxx002 comes supplied with a rechargeable battery pack.
Power Supply Compatible Motors
MTBWAND18-25 | Battery Tube for 18/25mm DCRF (no Battery) Mtrs
(inc Mt clips)
MT01-4001-069003
MTDCPS-18-25 | Power Supply for 18/25-CL/Tilt DCRF (no Bttry) Mtr
MTBPCKR-28 | Rechargeable Wand
MT03-0301-069011 | USB Wall Charger - 5V, 2A (AU ONLY)
MT01-4001-xxx002
MT03-0301-069008 | USB Wall Charger - 5V, 2A (US ONLY)
MT03-0301-069007 | 4M (13ft) USB Micro Cable
MT03-0302-067001 | Solar Panel Gen2
Extension Cables Compatible with
MTDC-CBLXT6 DC Battery Motor Cable extender 6” / 155mm
MT01-4001-069003MTDC-CBLXT48 DC Battery Motor Cable extender 48” / 1220mm
MTDC-CBLXT96 DC Battery Motor Cable extender 96” / 2440mm
MT03-0301-069013 | 48”/1200mm 5V Cable Extender
MT01-4001-xxx002MT03-0301-069014 | 8”/210mm 5V Cable Extender
MT03-0301-069
4.1 Power Options

ROLLEASE ACMEDA Automate™Programming Instructions | Tilt Motors | 9
5.1 Motor state test
5.2 Motor configuration options
This table describes the function of a short P1 Button press/release (<2 seconds) depending on current motor
configuration.
The P1 Button is utilized to administer motor configurations as described below.
Activate Pairing Mode
Approx.
Approx.
Approx.
Sleep Mode
Reverse Direction
Approx.
Reset To Factory Settings
Approx.
Approx.
5 P1 BUTTON FUNCTIONS
P1
Press Condition Function Achieved
Visual
Feedback
Audible
Feedback Function Described
Short
Press
If limit is NOT set None No Action None No Action
If limits are set
Operational
control of motor,
run to limit. Stop
if running
Motor Runs None
Operational control
of motor after pairing
and limit setting is
completed first time
If motor is in
“Sleep Mode” &
limits are set
Wake and control
Motor wakes
and runs in a
direction
None
Motor is restored from
Sleep Mode and RF
control is active
Hold P1 button on motor head.
P1 button on motor head.
10
10
ONLY THE PASSTHROUGH MOTOR
EMITS A BEEPING NOISE.
IGNORE THIS ICON WHEN
PROGRAMMING MT01-4001-069003.
ALL OTHER PROMPTS ARE THE SAME
FOR BOTH MOTORS.
Approx.
Approx.
Approx.
Approx.
IMPORTANT

10 | Automate™Programming Instructions | Tilt Motors ROLLEASE ACMEDA
.
6.1 Pair motor with controller
6.2 Check motor direction
Consult user manual for your
controller for information on
selecting channel.
Damage to shade may occur when operating motor prior to
setting limits. Attention should be given.
Reversing motor direction using this method is only possible
during initial set-up
Hold P1 button on
motor head.
To check travel direction of shade, press UP or
DOWN on controller.
Quick Press = Step
Long Press = Continuous Travel
To reverse shade direction, hold both UP and
DOWN.
Until the motor responds.
Select channel on
controller.
Hold STOP on
controller.
Approx.
Approx.
Motor Response*
Motor Response*
NOTE: * ONLY THE PASSTHROUGH MOTOR BEEPS
Motor Response*
Motor is now in step mode and ready for setting limits
IMPORTANT IMPORTANT
IMPORTANT
6 INITIAL SET UP
OR

ROLLEASE ACMEDA Automate™Programming Instructions | Tilt Motors | 11
SEC
SEC
S
S
5
5
6.3 Set Limits
Cycle shade up and down prior to setting limits to settle fabric
After setting limits, motor will automatically exit from initial
set-up mode.
Move shade to the desired highest or lowest
position by pressing the UP or DOWN buttons
on controller.
Move shade to the desired highest or lowest
position by pressing the UP or DOWN buttons
on controller.
To save upper limit, hold UP and STOP.
To save lower limit, hold DOWN and STOP.
Motor Response*
Motor Response*
IMPORTANT
IMPORTANT
Approx.
Approx.
OR
OR
NOTE: * ONLY THE PASSTHROUGH MOTOR BEEPS

12 | Automate™Programming Instructions | Tilt Motors ROLLEASE ACMEDA
SEC
SEC
S
S5
5
7.1 Adjust upper limit
7.2 Adjust lower limit
Hold UP and STOP on
controller.
Hold DOWN and STOP
on controller.
Move shade to the desired
lowest position by pressing
the UP or DOWN button.
Move shade to the desired
highest position by pressing
the UP or DOWN button.
To save upper limit, hold UP
and STOP.
To save lower limit, hold
DOWN and STOP.
Approx.
Approx.
Motor Response*
Motor Response* Motor Response*
Motor Response*
7 ADJUSTING LIMITS
SEC SECS S
5 5
Approx. Approx.
The bottom limit should be set ~ 1.38 in. (35mm) below the Ultra-Lock to disengage the auto lock mechanism when the shade is raised.
IMPORTANT
OR
OR
NOTE: * ONLY THE PASSTHROUGH MOTOR BEEPS

ROLLEASE ACMEDA Automate™Programming Instructions | Tilt Motors | 13
8.1 Using P2 Button on existing controller to add a new controller or channel
8.2 Using a pre-existing controller to add or delete a controller or channel
A = Existing controller or channel (to keep)
B= Controller or channel to add or remove
A = Existing controller or channel (to keep)
B= Controller or channel to add or remove
Press P2 on
controller A.
Press P2 on
controller A.
Press P2 on
controller A.
Press P2 on
controller A.
Press P2 on the
controller Bto remove
it.
Press STOP on an new
controller to add it.
Motor Response*
Motor Response*
Motor Response*
Motor Response*
Motor Response*
Motor Response*
8 CONTROLLERS AND CHANNELS
Consult user manual for your controller or sensor
Consult user manual for your controller or sensor
IMPORTANT
IMPORTANT
NOTE: * ONLY THE PASSTHROUGH MOTOR BEEPS

14 | Automate™Programming Instructions | Tilt Motors ROLLEASE ACMEDA
9.1 Set a favorite position
9.2 Send shade to favorite position
9.3 Delete favorite position
Press P2 on controller. Press STOP on controller. Press STOP on controller.
Move shade to the desired position by pressing the UP or DOWN button on the controller.
Press P2 on controller. Press STOP on controller. Press STOP on controller.
Approx.
Motor Response*
Motor Response*
Motor Response*
Motor Response*
Motor Response*
Motor Response*
9 FAVORITE POSITIONING
OR
NOTE: * ONLY THE PASSTHROUGH MOTOR BEEPS

ROLLEASE ACMEDA Automate™Programming Instructions | Tilt Motors | 15
10 TILT & ROLLER MODE
Press STOP on controller.
Hold UP & DOWN on controller.
Hold UP & DOWN on controller.
Press STOP on controller.
Motor Response*
Motor Response*
Motor Response*
Motor Response*
10.1 Toggle motor to Tilt Mode
10.2 Toggle Motor to Roller Mode
Default motor mode is Roller after initial Limits have been set, use following steps to change to Roller Mode.
If motor is in Tilt Mode, use following steps to change to Roller Mode.
SEC
SEC
S
S
5
5
Approx.
Approx.
NOTE: * ONLY THE PASSTHROUGH MOTOR BEEPS

16 | Automate™Programming Instructions | Tilt Motors ROLLEASE ACMEDA
11.2 Decrease Motor Speed
11.1 Increase Motor Speed
11 ADJUSTING SPEED
Press P2 Press DOWN Press DOWN
Motor Response* Motor Response* Motor Response*
Press P2 Press UP Press UP
Motor Response* Motor Response* Motor Response*
NOTE: * ONLY THE PASSTHROUGH MOTOR BEEPS
NOTE: Repeating this step when at the slowest speed EXITS Soft Stop Mode in MT01-4001-069001.
NOTE: Repeating this step when at the fastest speed ENTERS Soft Stop Mode in MT01-4001-069001.

ROLLEASE ACMEDA Automate™Programming Instructions | Tilt Motors | 17
9 SLEEP MODE
Enter Sleep Mode
Sleep mode is utilized to
prevent a motor from incorrect
configuration during other
motor setup.
Hold P1 button on the motor
head
If multiple motors are grouped on a single channel, Sleep Mode may be used to put all but 1 motor to sleep,
allowing programming of just the one motor that remains “Awake”. See page 6 for detailed P1 functions.
Exit Sleep Mode: Method 1
Exit sleep mode once the shade
is ready.
Press and release P1 button on
the motor head
Exit Sleep Mode: Method 2
Remove power and then
re-power the motor.
Motor Response* Motor Response*
12 SLEEP MODE
Approx.
NOTE: * ONLY THE PASSTHROUGH MOTOR BEEPS

18 | Automate™Programming Instructions | Tilt Motors ROLLEASE ACMEDA
G
13 TROUBLE SHOOTING
Problem Cause Remedy
Motor is not responding Battery in motor is depleted Recharge with a compatible
charger
Insufficient charging from solar
PV panel
Check connection and orientation
of PV panel
Controller battery is discharged Replace battery
Battery is inserted incorrectly
into controller
Check battery polarity
Radio interference/shielding Ensure transmitter is positioned
away from metal objects and
the aerial on motor or receiver
is kept straight and away from
metal
Receiver distance is too far from
transmitter
Move transmitter to a closer
position
Charging failure Check power supply to motor is
connected and active
Motor beeps x10 when in use Battery voltage is low Recharge with a compatible
charger
Cannot program a single motor
(multiple motors respond)
Multiple motors are paired to the
same channel
Always reserve an individual
channel for programming
functions. Use Sleep Mode to
program individual motors.
rolleaseacmeda.com

ROLLEASE ACMEDA Automate™Programming Instructions | Tilt Motors | 19
NOTES

20 | Automate™Programming Instructions | Tilt Motors
ROLLEASE ACMEDA
AUSTRALIA
110 Northcorp Boulevard,
Broadmeadows VIC 3047
T [phone] | F [phone]
ROLLEASE ACMEDA
USA
200 Harvard Avenue
Stamford, CT 06902 6320
T [phone] | F [phone]
ROLLEASE ACMEDA
EUROPE
Via Conca Del Naviglio 18, Milan
(Lombardia) Italy
T [phone] | F [phone]
Queensland Branch
Unit 2/62 Borthwick Avenue,
Murarrie QLD 4172
[e-mail]
rolleaseacmeda.com