rollease acmeda Easy Link User manual

EASY LINK
INSTALLATION MANUAL
February 2017

Page 1 EASY LINK Installation Manual | February 2017
© Copyright 2017 | Rollease Acmeda Group
CONTENTS
February 2016
This manual is to be read in conjunction with the Product Specifications & Assembly manual
SECTION NO.
DESCRIPTION
PAGE NO.
SECTION 1 – TOOLS & ADDITIONAL ITEMS REQUIRED 1.1
SECTION 2 – INSTALLATION 2.3
PART A –BRACKET INSTALLATION 2.3
PART B – SHADE INSTALLATION 2.4
PART C – INSTALLED SHADE 2.9
DISCLAIMER
INTRODUCTION
This Installation manual has been produced by Rollease Acmeda to supply the necessary information for safe and correct installation of this system.
INSTALLERS RESPONSIBILITY
Before installing, please read & ensure you understand the safety information and installation instructions as defined in this installation manual.
•If you do not fully understand these instructions, contact Rollease Acmeda for clarification before installing.
•The Installer is responsible to ensure that all installation personnel have been adequately trained on the safe & correct installation and operation.
•The Installer is responsible to ensure that supporting structures are sound and can adequately support the load.
•The fasteners provided are intended for fastener to timber. The Installer is responsible for selecting fasteners that are suitable for other substrates
SAFETY INFORMATION
•Ensure that electrical works are done only by a LICENSED ELECTRICIAN.
•DO NOT modify any of the components of this system.
PERSONNEL REQUIREMENTS
Only suitably trained/qualified personnel should undertake installation.
DISCLAIMER
Rollease Acmeda has used reasonable care in preparing the information included in this document, but makes no representations or warranties as to the completeness or
accuracy of the information. Information is supplied upon the condition that the persons receiving the information will make their own determination as to its suitability for their
purposes prior to use. Rollease Acmeda assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included
herein. Rollease Acmeda reserves the right to make changes without further notice to any products to improve reliability, function or design.
COPYRIGHT
COPYRIGHT © ROLLEASE ACMEDA 2016
All rights reserved. No part of this document may be reproduced or utilized in any means, by any means, electronic or mechanical including photocopying, recordings, or by any
information storage or retrieval system, without the express permission from Rollease Acmeda.

Page 1.1 EASY LINK Installation Manual | February 2017
© Copyright 2017 | Rollease Acmeda Group
SECTION 1 – TOOLS & ADDITIONAL ITEMS REQUIRED
TOOLS REQUIRED
•
Drill
•Drill Bits
•Screw Driver – Philips Head
•Measuring Tape
•
Pencil
ADDITIONAL ITEMS REQUIRED (NOT SUPPLIED)
To install EASY-LINK, the following non-stocked items are required:
•
Fastener Screws – Installer to use appropriate fasteners/fasteners to suit application

Page 1.2 EASY LINK Installation Manual | February 2017
© Copyright 2017 | Rollease Acmeda Group
SHADE ITEMS REQUIRED
EASY-LINK
5
4
2
3
1
1
2
Check you have all Shade items;
1. Easy-Lock LX Bracket
2. Easy-Link LX Bearing Bracket
3. Shade “A” (Idler Side)
4. Shade “B” (Control Side)
5. Shade “X” (Linking Shade)
(OPTIONAL: THERE CAN ALSO BE
MULTIPLE OF SHADE “X”)

Page 2.3 EASY LINK Installation Manual | February 2017
© Copyright 2017 | Rollease Acmeda Group
SECTION 2 – INSTALLATION
PART A –BRACKET INSTALLATION
STEP 1 – PREPARE BRACKETS ENSURING LEVEL AND CORRECT DISTANCES APART
EASY-LINK – Wall Fix
EASY-LINK – Ceiling Fix
STEP 2 – INSTALL BRACKET TO WALL/CEILING USING APPROPRIATE FASTENERS TO SUIT APPLICATION
EASY-LINK – Wall Fix
EASY-LINK – Ceiling Fix

Page 2.4 EASY LINK Installation Manual | February 2017
© Copyright 2017 | Rollease Acmeda Group
PART B – SHADE INSTALLATION
STEP 1 – INSTALL SHADE “B” FIRST (CONTROL SHADE)
NOTE: Retract female Easy-Link Drive
by rotating counter-clockwise
NOTE: Insert Control end of Shade in first then swing in female Easy-Link end
NOTE: Extend the female Easy-Link by rotating clockwise, Ensure pin is fully extended through Easy-Link Bracket

Page 2.5 EASY LINK Installation Manual | February 2017
© Copyright 2017 | Rollease Acmeda Group
STEP 2 – INSTALL SHADE “X1” (WHEN INSTALLING 3 SHADES)
NOTE: Retract female Easy-Link Drive
by rotating counter-clockwise
NOTE: Ensure weight bars are at even heights when installing Shade “A”
Insert Easy-Link Drive end of Shade in first then swing in Idler End
NOTE: Extend the female Easy-Link by rotating clockwise, Ensure pin is fully extended through Easy-Link Bracket

Page 2.6 EASY LINK Installation Manual | February 2017
© Copyright 2017 | Rollease Acmeda Group
STEP 3 – LEVEL SHADES AS THEY ARE INSTALLED (IF WEIGHTBARS ARE NOT HANGING LEVEL)
NOTE: Rotate Male Easy-Link Wheel counter clockwise to retract the pin connection
NOTE: Rotate fabric/tube until weight bars are in line
STEP 4 – INSTALL NEXT SHADE “X” AND LEVEL (IF INSTALLING 3 OR MORE LINKED SHADES)
SEE SECTION 2, PART B, STEPS 2-3, FOR DETAILS
PROCESS: INSTALL SHADE X2– THEN LEVEL
INSTALL SHADE X3– THEN LEVEL
INSTALL SHADE X4– THEN LEVEL
(CONTINUE AS REQUIRED)

Page 2.7 EASY LINK Installation Manual | February 2017
© Copyright 2017 | Rollease Acmeda Group
STEP 5 – INSTALL SHADE “A” (IDLER SHADE)
NOTE: Retract Idler Pin by rotating
counter-clockwise
NOTE: Ensure weight bars are at even heights when installing Shade “A”
Insert Easy-Link Drive end of Shade in first then swing in Idler End
NOTE: Extend the Idler Pin by rotating clockwise, Ensure pin is fully extended through Bracket

Page 2.8 EASY LINK Installation Manual | February 2017
© Copyright 2017 | Rollease Acmeda Group
STEP 6 – LEVEL SHADE “A” (IF WEIGHTBARS ARE NOT HANGING LEVEL)
SEE SECTION 2, PART B, STEP 3, FOR DETAILS
STEP 7 –TEST SHADE TO ENSURE IT IS OPERATING CORRECTLY, LEVEL AND IN SYNC