rollease acmeda Easy Spring Plus User manual

1
Cordless Roller Roman Shade
with Easy Spring Plus
Fabricaon Instrucons
Table of Contents
Components Needed…….……………………………………………… Pages 2-3
Assembly Drawing & Spring/Stop Posioning ………….…… Page 4
Fabricaon Instrucons ………………………………………………… Pages 5-13
Minimum Shade Size per Spring………………………….. Page 6
How to Select a Spring………………………………………… Page 6
How to Set the Stop Plate …..…………………………….. Page 7
Pre-Rotaon Instrucons and Charts …….……………. Page 8-9
Trouble-shoong…………………………………………………………….Page 14
Easy
Spring
Plus
CORDLESS SHADE SYSTEM
by Rollease Acmeda

1
Easy Spring Plus Components
Qty Needed Item Rollease Acmeda Part #
1Headrail
RE0080110
Varies depending
on width of
shade (max 18”
between
brackets)
Mounting
Brackets
RE0080200
1
Left Side Spring
1-1/2” (38mm) RE0080400 1.2 x 300mm
RE0080500 1.5 x 450mm
RE0084400 1.7 x 550mm
1
Right Side Stop
1-1/2” (38mm) RE0084810 - 1-1/2" short
2
Bracket W/
Adjuster Wheel
1-1/2”(38mm) RE0080710- 1-1/2"
1
Tube
1.5”diameter
1Pre-Rotaon Tool
Note: 38mm components are shown in these instructions on Roller Roman shades
due to their weight. 32mm are not recommended.
Easy
Spring
Plus
CORDLESS SHADE SYSTEM
by Rollease Acmeda
16' white sold 12 ea
Sold 25 ea
sold 25 ea
All Brackets are white - sold as ea
sold as ea
RTEA4T12 -1.5 X 12’
RTEA4T16 - 1.5 X 16’
RE0084200 1.5" (38mm)

2
Roller Roman Components
1
Lift Cord 1.2mm
or your
preferance
V2LC100
V2LC305
V2LC885
Roller Roman
Tube Clips RRTC15
1Pull ring
1Your Roman
shade, assembled
1Your covered
dustboard
Easy
Spring
Plus
CORDLESS SHADE SYSTEM
by Rollease Acmeda
1.2mm white
1.2mm sand
1.2mm bronze
sold in 1000 yard/roll
1-1/2"
1 Short Stack & Forever
Ring per ROW per
COLUMN
1 Short Stack and Level
Lock PER COLUMN - in
place of an Orb
STSFR Forever Ring 1000 ea
STSRL Short Stack 1.4mm 1000 ea
Short Stack
Level Lock
Forever Ring
1 set for each row
A short stack is used
with each Ring AND
with each Level Lock in
place of an Orb.
Varies depending
on size of tube
(5 lbs per lift cord max)
Not provided
Not provided
Not provided
STSRL09 Short Stack .9mm 1000 ea
STSLLILP Level Lock 100 ea
Qty Needed Item Rollease Acmeda Part #
CHILD SAFETY PRODUCT

4
Roller Roman Assembly - Shade Styles
Note: Posion of spring and stop depends on type of Roman shade you’re making. When
assembling your shade, use a scker or similar to mark spring side for later reference.
Waterfall Shade (with fabric dropping o the front of
the dustboard)
If you’re facing BACK of shade as shown below, Spring
will be on your LEFT and Stop will be on your RIGHT.
Standard Shade with Grommets (with fabric dropping
o the back of the dustboard)
If you’re facing FRONT of shade as shown below,
Spring will be on your LEFT (see scker) and stop will
be on your RIGHT.
Easy
Spring
Plus
CORDLESS SHADE SYSTEM
by Rollease Acmeda
A TUBE AND TUBE
CLIPS NEEDS TO
BE ADDED TO
THIS DRAWING

5
Deducons
Step 1. Determine Size of Dustboard
Step 2. Cut headrail 1” smaller than dustboard
(leaving 1/2” on each side of dust board. See diagram below)
Step 3. Cut Tube 1-3/8” smaller than headrail
(leaving 11/16” on each side of headrail. See diagram below)
Diagram
Example – 40” Shade
1. Make sure you have a clean working area.
2. Lay all parts on fabricaon table.
3. Assemble Roman shade panel with li cord (per your usual method).
4. Use 1”x 3” or 1”x 2” true covered dust board (per usual method).
To Begin:
Tools Required
1. Tape measure (with 16th increments)
2. Scissors
3. Screw gun
4. Metal saw (for cung rail and tube)
Easy
Spring
Plus
CORDLESS SHADE SYSTEM
by Rollease Acmeda