rollease acmeda Skyline Easy-Link User manual

SKYLINE EASY-LINK
ASSEMBLY MANUAL
June 2019

CONTENTS
June 2019
This manual is to be read in conjunction with the Product Specifications manual
SECTION NO.
DESCRIPTION
PAGE NO.
SECTION 1 −TOOLS AND ADDITIONAL ITEMS REQUIRED 1.1
SECTION 2 −SYSTEM DETAILS 2.1
PART A –OVERVIEW 2.1
PART B –DEDUCTIONS 2.2
PART C –BOM & CUTTING LIST 2.2
SECTION 3 ASSEMBLY 3.3
PART A –ASSEMBLING TUBE 3.3
PART B –PREPARE & PACK ASSEMBLIES READY FOR TRANSPORTATION & INSTALLATION 3.5
DISCLAIMER
INTRODUCTION
This product specifications manual has been produced by Rollease Acmeda to supply the necessary information for safe and correct assembly and installation of this
system.
DISCLAIMER
Rollease Acmeda has used reasonable care in preparing the information included in this document, but makes no representations or warranties as to the completeness or
accuracy of the information. Information is supplied upon the condition that the persons receiving the information will make their own determination as to its suitability
for their purposes prior to use. Rollease Acmeda assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the
information included herein. Rollease Acmeda reserves the right to make changes without further notice to any products to improve reliability, function or design.
COPYRIGHT
COPYRIGHT © ROLLEASE ACMEDA 2019
All rights reserved. No part of this document may be reproduced or utilised in any means, by any means, electronic or mechanical including photocopying, recordings, or
by any information storage or retrieval system, without the express permission from Rollease Acmeda.

Page 1.1
SKYLINE EASY-LINK Assembly Manual | June 2019
Copyright © 2019 Rollease Acmeda Group.
SECTION 1 −TOOLS AND ADDITIONAL ITEMS REQUIRED
TOOLS REQUIRED
•Saw
•Drill
•Drill Bits
•Screw Driver –Phillips Head, Flat Head
•Scissors
•Measuring Tape
•Pencil
ADDITIONAL ITEMS REQUIRED (NOT SUPPLIED)
To assemble a SKYLINE EASY-LINK, the following non-stocked items are required:
•Fabric

Page 2.1
SKYLINE EASY-LINK Assembly Manual | June 2019
Copyright © 2019 Rollease Acmeda Group.
SECTION 2 −SYSTEM DETAILS
PART A –OVERVIEW
SKYLINE EASY-LINK
The Rollease Acmeda Skyline Easy-Link™ system was designed to allow for multiple blinds to be controlled using a single motor control operation.
Achieving minimal gaps between each blind, the Skyline Easy-Link™ system provides the perfect solution for linking roller blinds.
SYSTEM INDEX
1. Medium Easy-Link Intermediate Male Drive
2. Medium Link Skyline Bracket
3. Medium Easy-Link Intermediate Female Drive
4. Medium Multi-Link Bracket Disk & Bearing
SKYLINE EASY-LINK | DUAL CONTROL
The Rollease Acmeda Skyline Easy-Link™ system combined with the Pin to Pin Disk allows for multiple controls to be used on a single installation
allowing for maximum user customisation.
SYSTEM INDEX
1. Skyline Pin End
2. Medium Link Skyline Bracket
3. Medium Link Bracket Disk Pin to Pin
3
1
2
4
1
2
1
3

Page 2.2
SKYLINE EASY-LINK Assembly Manual | June 2019
Copyright © 2019 Rollease Acmeda Group.
PART B –DEDUCTIONS
FABRIC/TUBE LIGHT GAP
SKYLINE EASY LINK
PIN TO PIN
EASY-LINK
19mm
19mm
(0.75”)
(0.75”)
PART C –BOM & CUTTING LIST
SKYLINE EASY-LINK
PART NUMBER
DESCRIPTION
U.O.M
QTY
DEDUCTION
SKYLINE
EASY-LINK OPTIONS
BRACKETS
RB41-0321-XXX138
Medium Link Skyline Bracket | Narrow |
38mm
Piece
n
RB41-0321-XXX050
Medium Link Skyline Bracket | Narrow |
50mm
Piece
RB41-0332-XXX060
Medium Link Skyline Bracket | Double V Slim
Piece
RB41-0331-XXX075
Medium Link Fascia Bracket
Piece
RB41-0502-XXX000
Medium Easy-Link Bracket Disk + Bearing
Piece
RB41-0503-XXX000
Medium Link Bracket Disk Pin to Pin
Piece
DRIVES
RB41-1001-XXX038
Medium Easy-Link Intermediate Male Drive
Set
1 x n
RB41-1002-XXX038
Medium Easy-Link Intermediate Female Drive
Set
1 x n
NOTE: n= number of Skyline Easy-Link Brackets required for installation

Page 3.3
SKYLINE EASY-LINK Assembly Manual | June 2019
Copyright © 2019 Rollease Acmeda Group.
SECTION 3 ASSEMBLY
PART A –ASSEMBLING TUBE
STEP 1 –INSERT INTERMEDIATE MALE SKYLINE EASY-LINK DRIVE INTO BLIND “A”
NOTE: THE FINS ON ALL DRIVE UNITS SHOULD BE ALIGNED OUTSIDE THE FINS IN THE TUBE

Page 3.4
SKYLINE EASY-LINK Assembly Manual | June 2019
Copyright © 2019 Rollease Acmeda Group.
STEP 2 –INSERT INTERMEDIATE FEMALE SKYLINE EASY-LINK DRIVE INTO BLIND “B”
STEP 3 –INSERT INTERMEDIATE MALE & FEMALE SKYLINE EASY-LINK DRIVES INTO BLIND “X” (WHEN USING 3+ BLINDS)
NOTE: Repeat step 3 for each Blind “X” being used
FEMALE
MALE
IDLER END
CONTROL END

Page 3.5
SKYLINE EASY-LINK Assembly Manual | June 2019
Copyright © 2019 Rollease Acmeda Group.
PART B –PREPARE & PACK ASSEMBLIES READY FOR TRANSPORTATION & INSTALLATION
SKYLINE EASY-LINK
SKYLINE EASY-LINK | DUAL CONTROL
Check you have all blind items;
1. Skyline Bracket | Narrow
2. Medium Link Skyline Bracket | Narrow
3. Medium Easy-Link Bracket Disk + Bearing
4. Blind “A” (Idler Side)
5. Blind “B” (Control Side)
6. Blind “X” (Linking Blind)
(OPTIONAL: THERE CAN ALSO BE
MULTIPLES OF BLIND “X”)
1
2
2
1
4
6
5
3
3
Check you have all blind items;
1. Skyline Bracket | Narrow
2. Medium Link Skyline Bracket | Narrow
3. Medium Link Bracket Disk Pin to Pin
4. Medium Easy-Link Bracket Disk + Bearing
5. Blind “A” (Left Control)
6. Blind “B” (Right Control)
7. Blind “X” (Linking Blind)
1
2
2
1
5
7
6
3
4