Ronda startech 5040.B User manual

Cal. 5040.B
English
User’s Manual
30
10
20
10 1
2
3
4
5
6
7
8
9
15
60
30
45
21
III
10
20
30
10 1
2
3
4
5
6
7
8
9
15
60
30
45
17
III
10
20
30
10 1
2
3
4
5
6
7
8
9
15
60
30
45
30
Setting the date/time
following a battery change
Example:
– Date / time on the watch: / 1:25 AM
– Present date / time: / 8:30 PM

Pull out the crown to position II
(the watch continues to run).

Turn the crown until yesterday’s date
appears .
03
17
04
Crown
Date


I II III
10
20
30
10 1
2
3
4
5
6
7
8
9
15
60
30
45
30
I II III
10
20
30
10 1
2
3
4
5
6
7
8
9
15
60
30
45
4
0

**Pull out the crown to position
III
(the watch stops).

**Turn the crown until the correct date
appears.

**Continue to turn the crown until the
correct time 8:30 PM appears.

**Push the crown back into position
I .
04
Please note:
**To set your watch to the exact second,
please refer to the chapter entitled «setting
the time».
**Please observe the AM/PM clock rhythm.
Second hand





RONDA AG
CH-4415 Lausen/Switzerland
www.ronda-startech.com
11/2006
Battery type: 395 (diameter 9.5mm x 2.6mm / SR 927 SW)
Accuracy: +20 / -10 seconds per month
In case your watch needs to be repaired or to raise claims
under a guarantee, please contact the point of sales
30
10
20
10 1
2
3
4
5
6
7
8
9
15
60
30
45
21
Description of the display and control buttons
Display elements
Date
Second hand
Minute hand
Hour hand
Centre stop-second
Minute counter
1⁄10 second counter
(houer counter after 30 minutes)
Control buttons
Push button A
Crown
Push button B
10
20
30
10 1
2
3
4
5
6
7
8
9
15
60
30
45
21
10
20
30
10 1
2
3
4
5
6
7
8
9
15
60
30
45
21
Chronograph: Basic function
(Start / Stop / Reset)
Example:
Start:
Press push-button A .
Stop:
to stop the timing, press push-
button A once more and read the three
chronograph hands:
4min
/ 38sec /
7⁄10 sec
Zero positioning:
Press push-button B .
(The three chronograph hands will be reset
to their zero positions).

Push-button A
Push-button B

Minute counter
1⁄10 second counter
10
20
30
10 1
2
3
4
5
6
7
8
9
15
60
30
45
21
10
20
30
10 1
2
3
4
5
6
7
8
9
15
60
30
45
21
Chronograph:
Accumulated timing
Example:
Start:
(start timing)
Stop:
(e.g. 15 min 5 sec following

)
Restart:
(timing is resumed)

*
Stop: (e.g. 13 min 5 sec following

)
=28 min 10 sec
( The accumulated measured time is shown )
Reset:
The three chronograph hands are returned
to their zero positions.




Push-button A
Push-button B

Please note:
* Following

, the accumulation of the
timing can be continued by pressing
push-
button A
(Restart / Stop, Restart / Stop, …)
Minute counter
1⁄10 second counter
10
20
30
10 1
2
3
4
5
6
7
8
9
15
60
30
45
21
10
20
30
10 1
2
3
4
5
6
7
8
9
15
60
30
45
21
Chronograph:
Intermediate or interval timing
Example:
Start:
(start timing)
Display interval:
e.g. 10 minutes 10 seconds (timing
continues in the background)
Making up the measured time:
(the 3 chronograph hands are quickly
advanced to the ongoing measured time).
Stop:
(Final time is displayed)
Reset:
The 3 chronograph hands are returned to
their zero position
Push-button A
Push-button B
Push-button B



Please note:
* Following

, further intervals or inter-
mediates can be displayed by pressing
push-button B (display interval / make up
measured time, ...)
*

Minute counter
1⁄10 second counter
10
20
30
10 1
2
3
4
5
6
7
8
9
15
60
30
45
I II III
21
10
20
30
10 1
2
3
4
5
6
7
8
9
15
60
30
45
21
III
Adjusting the chronograph
hands to zero position
Example:
One or several chronograph hands are not in
their correct zero positions and have to be
adjusted (e.g. following a battery change).

Pull out the crown to position III (all 3
chronograph hands are in their correct or
incorrect zero position).

Keep push-buttons A and B depressed
simultaneously for at least 2 seconds
(the centre stop-second rotates by
360°
 corrective mode is activated).
Center stop-
second
Push-button A
Push-button B



Minute counter
1⁄10 second counter
Adjusting the centre stop second
A
A
1 x short
long
Single step
Continuous
Adjusting the next hand B
Adjusting the next hand B

Returning the crown to position I
Termination of the chronograph hands adjustment
(can be carried out at any time).
III
III
A
B
A
A
B
A
A
1 x short
long
Single step
Continuous
A
A
1 x short
long
Single step
Continuous


Adjusting the 1⁄10 second counter hand (position 6h)
Adjusting the minute counter hand (position 9h)





I II III
10
20
30
10 1
2
3
4
5
6
7
8
9
15
60
30
45
21
I II III
10
20
30
10 1
2
3
4
5
6
7
8
9
15
60
30
45
21
Setting the time

*Pull out the crown to position
III
(the watch stops).

Turn the crown until you reach the correct
time
8:45 .

*Push the crown back into position
I.
Please note:
* In order to set the time to the exact second,

must be pulled out when the second hand
is in position «60».
Once the hour and minute hands have been
set,

must be pushed back into position I at
the exact second.
Second hand


III
10
20
30
10 1
2
3
4
5
6
7
8
9
15
60
30
45
31
III
10
20
30
10 1
2
3
4
5
6
7
8
9
15
60
30
45
1
0
Setting the date (quick mode)

Pull out the crown to position II (the watch
continues to run).

Turn the crown until the correct
date appears.

Push the crown back into position I .
01


Please note:
During the date changing phase between
9 PM and 12 PM; the date must be set to the
date of the following day.
An extreme acceleration in setting the date
with quick mode can induce a false date indi-
cation. The synchronization is re-established
by setting the date from 01 till 31 (crown in
position II).