ROOMS TO GO CREEKSIDE 2.0 User manual

WARNING DANGER
Failure to follow these warnings and assembly instructions could result in serious
injury or death. To help prevent serious or fatal injuries from entrapment or falls:
-
Read all instructions before assembling bunk bed and keep these instructions for future reference.
-
Before each usage or assembly, inspect bunk bed for damaged hardware, loose joints, missing
parts, or sharp edges. DO NOT Use bunk bed if any parts are missing or broken.
-
DO NOT Use substitute parts. Contact your local Rooms To Go or visit www.ROOMSTOGO.COM
for replacement parts and instructional literature if needed.
-
Follow the information on the warnings appearing on the upper bunk end structure and on the carton,
DO NOT REMOVE WARNING LABEL FROM BED.
-
Always use the recommended size mattress or mattress supports, or both to help prevent the likelihood
of entrapment or falls.
-Ensure thickness of mattress and foundation combine does not exceed
10 inches (255mm
) and
mattress surface is at least
5 inches (127mm)
below upper edge of guardrails.
-
Do not allow children under 6 years of age to use the upper bunk.
-
Periodically check and ensure that the guardrail, ladder, and other components are in their proper
position, free from damage, and that all connectors are tight.
-
Do not allow horseplay on or under the bed and prohibit jumping on the bed.
-
Limit top bunk use to one person.
-
Always use the ladder for entering and leaving the upper bunk.
-
Use of night light may provide added safety precaution for a child using the upper bunk.
-
Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed next to
the wall, the guardrail that runs the full length of the bed should be placed against the wall to
prevent entrapment between the bed and wall.
-
The use of water or sleep flotation mattress is prohibited.
-
This bunk bed meets all the requirements of ASTM 1427-19.
STRANGULATION HAZARD:
Never attach or hang items to any part of the bunk bed that are not designed for
use with the bed; for example, but not limited to, hooks, belts, and jump ropes.
CREEKSIDE 2.0 COLLECTION
THANK YOU FOR YOUR PURCHASE
11/7/2022 Page 1 of 97

35740403 40G-705 TWIN LOFT END
36940408 40G-709 FULL CASTER BED HD & FT
P A R T S L I S T
3924040P TWIN/FULL STEP LOFT W/CHEST CHARCOAL
RTG SKU # STYLE # ITEM DESCRIPTION
35840405 40G-160 STEP STORAGE UNIT
37040401 40G-735 TWIN RAIL CAP
38000232 100-645 TW. SLAT PACK (4)
36640402 40G-730 6 PC RAILS (2 GUARD & 4 SIDE RAILS)
36040400 40G-711 LOFT CHEST
3924041P TWIN/FULL STEP LOFT W/CHEST CHESTNUT
RTG SKU # STYLE # ITEM DESCRIPTION
35840417 40B-160 STEP STORAGE UNIT
38100234 100-646 FULL SLAT PACK (4)
36240404 40G-601 FOLDING DESK (Add on)
36640414 40B-730 6 PC RAILS (2 GUARD & 4 SIDE RAILS)
36040412 40B-711 LOFT CHEST
35740415 40B-705 TWIN LOFT END
36940410 40B-709 FULL CASTER BED HD & FT
38100234 100-646 FULL SLAT PACK (4)
36240416 40B-601 FOLDING DESK (Add on)
37040413 40B-735 TWIN RAIL CAP
38000232 100-645 TW. SLAT PACK (4)
TOOLS NEEDED
11 Pc
71 Pc
24 Pcs
Phillips screwdriver (not included)
5/16"-18 x 3 3/8" Bolt
PARTS LIST QTY PARTS LIST QTY HARDWARE LIST QTY
32 Pc
Drywall screw
2 Pcs
Twin top bunk bed end
1 Pc
Allen wrench (included)
24 Pc Step bunk unit 5 mm Hex key
FOLDING DESK HARDWARE
2 Pcs
Guardrails Loft chest 3/8" x 3 1/8"
Metal pin 6 x 1 1/4"
81 Pc
16 Pcs
Side rails 6 x 1 1/4"
61 Pc 11 1 Pc
Twin rail cup
Casters
Twin slats Caster bed headboard
54 Pc 10 1 Pc
44 Pc 91 Pc 4 Pcs
Drywall screw
Folding desk (Add on)
11/7/2022 Page 25 of 97
Full slats Caster bed footboard
A
B
C
D
C
E

STAIRS ON THE RIGHT
STAIRS ON THE LEFT
(Factory setting)
ASSEMBLY INSTRUCTIONS
FIRST DETERMINE THE CONFIGURATION THAT FITS YOUR ROOM
Assemble top side rails. then fasten with 1 1/4" screws.
11/7/2022 Page 26 of 97
For stairs on the left, first remove the screws, then remove the panel
and install it on the other side and secure with the screws. Assemble loft chest and top bunk bed end.
Install slats, one on each end, two equally spaced in the middle,
STEP 3
STEP 2
STEP 1
C
D
B
C
A
AA
C
A
B
D
D
B
A
A

ASSEMBLY INSTRUCTIONS
Slide Caster bed under Loft bed as shown.
11/7/2022 Page 27 of 97
Assemble guardrails and tighten all bolts. Assemble side rails
MAKE SURE ALL BOLTS ARE TIGHTENED COMPLETELY MAKE SURE ALL BOLTS ARE TIGHTENED COMPLETELY
Install slats, one on each end and two equally spaced in the middle,
then fasten with 1 1/4" screws Install casters in headboard and footboard, and set rail cup.
STEP 4
A
B
STEP 6
A
A
B
A
A
A
A
A
B
C
C
STEP 5
STEP 7 E
STEP 8
E
A
B
E

Twin size mattress- 74" - 75" long and 37-1/2" - 38-1/2" wide
Twin size Bunkie board- 74" long and 37-1/2" wide
Full size mattress- 74" - 75" long and 52-1/2" - 53-1/2" wide
Full size Bunkie board- 74" long and 52-1/2" wide
ASSEMBLY INSTRUCTIONS
11/7/2022 Page 28 of 97
Place Bunkie boards (required, sold separately) on top of the slats
Use only correct mattress dimensions and Bunkie board:
PLEASE CONTACT YOUR RETAIL STORE WITH SERVICE OR PARTS REPLACEMENT REQUEST
STEP 9

ASSEMBLY INSTRUCTIONS
Unfold corner supports (from desk box hardware pack) in the pre-bore hole.
Place folding desk by sliding into the opening of loft chest
then push down
Remove center molding by lifting up then pulling out Unfold desk leg and look for hardware pack inside desk box.
Secure each corner block with 1 1/4" screw
11/7/2022 Page 29 of 97
STEP 10
STEP 12
STEP 11
STEP 13
STEP 14
C
C

Twin size mattress- 74" - 75" long and 37-1/2" - 38-1/2" wide
Twin size Bunkie board- 74" long and 37-1/2" wide
Full size mattress- 74" - 75" long and 52-1/2" - 53-1/2" wide
Full size Bunkie board- 74" long and 52-1/2" wide
ASSEMBLY INSTRUCTIONS
Place Bunkie boards (required, sold separately) on top of the slats
11/7/2022 Page 30 of 97
Use only correct mattress dimensions and Bunkie board:
PLEASE CONTACT YOUR RETAIL STORE WITH SERVICE OR PARTS REPLACEMENT REQUEST
STEP 15