ROOMS TO GO LIN50-216 User manual

during shipment. Separate, identify and count all parts and metal hardware.
TOOLS REQUIRED
5 DRAWER CHEST
ATTENTION:
Be sure to check all packing material carefully for small parts which may come loose inside carton Important:
PAGE 1 O 2
5 Pcs
Compare with parts list and hardware illustrations to be sure all parts are present. If any part(s) are missing or
HARDWARE:
the model number and the parts needed.
(Not included)
Some lettered parts listed on the instruction sheets may not be in the parts bag, they
1 Pc INSTALLED
may already be assembled.
damage, contact your dealers customer services deparment. or efficient and fast service, please indicate
Phillips Screwdriver
Part No. HBJ-01-03690
Pull
INSTALLED 10 Pcs
ASSEMBLY INSTRUCTIONS
MODEL No
Part No.HB-488
WARNING INSTALL FURNITURE TIPPING RESTRAINT KIT
STEP 1 STEP 2
Remove pull from interior
of the drawers
Then put pull facing outside
Part No.HCPP-03 ANTI TIP
LIN50-216 / 32621600
Bolt 8-32 x 3/4" Zinc

ANTI-TIP
Installation instructions:
This tip restraint must be attached to wall stub using 2” screw enclosed
1.Attach a bracket securely to the back top rail of the furniture using the 5/8” screw pro ided through the smaller hole.
2. Locate the other bracket on the wall o er the wall stud and 2 inches below the mounting bracket secure to the back of
your unit. Attach to the wall stud using the 2’’ screw pro ided, through the smaller hole.
3. Place the furniture into position so both mounting brackets are ertically in line
4. Laces the end of the restraint strap though the larger hole in each mounting bracket. Bring both ends together and
slide the flat end through the looking end and flat draw it through until all slack is remo ed.
5. Confirm that the strap in securely laced and lacked.
Instrucciones de instalacion:
Este seguro contra olcado debe fijarse a un taco de pared con el tornillo de 2” que se incluye.
1. Coloque un soporte firmemente en la parte superior trasera del mueble ,usando el tornillo 5/8” que se proporciona y el
agujero mas pequeño
2. Ubique el otro soporte en la pared sobre un taco y 5cm (2pulg.) por debajo del soporte de montaje asegurado en la
parte bracera de la unidad .Fije al taco de pared usando el taco de 2’’ que incluye y el agujero mas pequeño .
3. Coloque el mueble en el sitio, de modo de modo que los dos soportes estén en una línea ertical.
4. Pase el extremo de una cinta de sujeción por el agujero más grande en cada soporte de montaje, una los dos
extremos y deslice el extremo plano por el lado del cierre, hasta que quede tenso.
5. Confirme que la cinta este bien asegurada.
Instructions d` installation:
Ce dispositif de sécurité doit être fixé au montai d` un mur a` l` aide de la is de 5cm (2 po) fournie
1. fixer solidement un support a`la tra ersé supérieure du meuble, en passant la is de 1,6cm (5/8 po) dans le plus petit
trou.
2. placer I` autre support sur un montant du mur, a` en iron 5cm (po) plus bas, par rapport au premier support de fixation,
fixer ce support en passant la is de 5cm (2 po) fournie dans le plus petit trou.
3. positionner le meuble afin d`aligner erticalement les deux supports de fixation
4. passer l`extrémité de i`attache dans les plus grands trous des deux supports. Joindre les extrémités insérer l`extrémité
plate dans le dispositif de blocage puis tirer au maximum pour desserrer.
5. érifier que l`attache est solidement fixée et bloquée.
Warning Advertencia Avertissement
WARNING INSTALL FURNITURE TIPPING RESTRAINT KIT
PAGE 2 O 2
Part No HB-488 (1PC)
Back View Furniture