ROOMS TO GO SYNE K2111-73PHR-Air User manual

Assembly Instructions
SYNE K2111-73PHR-Air Loveseat Recliner Console
w/pwer Headrest, Air massage
SKU# 15221156 / 15221170
Manufactured for Rooms To Go
***CAUTION: The item is heavy, assembly should be performed by two people in soft surface.
Parts# Desc. Pattern Q'ty Desc. Pattern Q'ty
A Wash 4 pieces B Butterfly
nut 4 pieces
CBolt (M8*3.14"，18 threads
per inch) 4 pieces D Transfor mer 2 pieces
Figure 1
Figure 2
Figure 3 Figure 4
C
D
C
D
C
D
A
B
C
D
G
H
A
B
A
B
C
D
D
C
C
D
A
B
A
B
A
B
C
D
E
F
E
E
E
F
E
F
E
F
E
F
F
F
G
H
I
I
E
F
1) The bolts package with a sticker "Hardware" is attached to the bottom of base rail.(See Figure 1)
2) Attached each bolt to corresponding pre-drilled holes by hand turning on clockwise direction as figure underneath.
(See Figure 2) Please attached to Screw the shorter threaded end of the bolt into the armrest and follow the arrow
direction to Insert the longer threaded end of the bolt into the hole in the base (Figure 3).
3) Please place the washers and Butterfly nut into the bolt as show by hand and then turning in clochwise direction until
it is tight.(See Figure 3)
D
C
D
A
B
A
B
C
D
P
D
C
P
C
C
D
C
D
P
C
D
A
B
P
A
B
C
D
A
B
A
B
D
C
D
A
B
A
B
C
D
P
D
C
P
C
C
D
C
D
P
C
D
A
B
P
A
B
C
D
A
B
A
B
D
C
D
A
B
A
B
C
D
P
D
C
P
C
C
D
C
D
P
C
D
A
B
P
A
B
C
D
A
B
A
B
C
D
P
C
D
A
B
P
A
B
C
D
C
D
A
B
A
B
A
B
A
B
C
D
P
D
C
P
C
D
C
D
C
D
P
C
D
A
B
P
A
B
C
D
C
D
A
B
A
B
A
B
A
B
C
D
P
D
C
P
C
D
C
D
C
D
P
C
D
A
B
P
A
B
C
D
C
D
A
B
A
B
A
B
A
B
C
D
P
D
C
P
C
D
C
D
C
D
P
C
D
A
B
P
A
B
C
D
C
D
A
B
A
B
A
B
A
B
C
D
P
D
C
P
C
D
C
D
Front

C
D
C
D
C
D
A
B
C
D
G
H
A
B
A
B
C
D
D
C
C
D
A
B
A
B
A
B
C
D
E
F
E
E
E
F
E
F
E
F
E
F
F
F
G
H
I
I
E
F
Step4
Locate the power cord C attached
to the bottom back and connect
Step 3
Slide the metal receiver over the
metal post.Press both sides of
back firmly downward until
A
B
A
B
C
D
C
D
A
B
C
D
A
B
A
B
C
D
C
D
A
B
C
D
A
B
A
B
C
D
C
D
A
B
C
D
A
B
A
B
C
D
C
D
A
B
C
D
Step 6
The Transformer is
attached to the bottom of
rail and connect to DC
Step 5
Locate the power cord E
attached to the bottom
back and connect to plug F
Step 2
Please located the hand controller
at the beside of metal bracket.
C
D
E
FG
P
G
C1 (Red Tape)
D1 (Red Tape)
D2
C2
A
B
P
C2
D2
D2
C2
C2
D2
A
B
P
C1 (Red Tape)
C1 (Red Tape)
C1 (Red Tape)
C1 (Red Tape)
D1 (Red Tape)
D1 (Red Tape)
D1 (Red Tape)
D1 (Red Tape)
C2
D2
A
B
E1
F1
G
P
E2
F2
C1 (Red Tape)
D1 (Red Tape)
D2
C2
C1 (Red Tape)
D1 (Red Tape)
C2
D2
A
B
A
B
E1
F1
Step1 . Console back (If applicable)
Remove the console back from the
bottom of the console.
Note: Make sure all PLUGS are connected on the product before plugging power cord into power outlet. If not
damage can occur.
The USB ports (where applicable) are designed with working voltage of 5V, and can NOT be used to supply power
for laptop computers (neither PC or Mac). Plugging a laptop computer to the USB port may end up damaging either
the computer or the USB port due to unmatched working voltage.
A
B
A
B
C
D
D
C
E
F
E
F