ROOMS TO GO 18504781 Setup guide

SETUP AND OPERATION GUIDE
TRIPLE PWR RECLINER
SKU: 18504781/ 18504793/ 18504806/ 18504818
Vendor Code: MVLC

Assembly of Your Lift Chair or Recliner
Operating Instructions For Triple Power Sku’s
Note:
2
3
4
5
Troubleshooting
Page 1
·
TABLE OF CONTENTS
Important Safety Instructions
When placing the furniture on non-carpeted flooring, it is recommended to use
some type of floor protection such as an area rug or furniture pads under the
chair glides. Area rugs and padding are not included with purchase.
NOTE: This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that
may cause undesired operation of the device. Modifications not approved by
the party responsible for compliance could void user's authority to operate
the equipment.
This power furniture is not intended for use by persons(including children)with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction regarding
the use of this item by a party responsible for their safety.
Children should be supervised to ensure that they do not play with or mishandle
any part of the operating system of this item.
Chair Assembly

Page 2
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING.
WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons:
DANGER: To reduce the risk of electric shock-Always unplug this furnishing from
the electrical outlet before cleaning.
Unplug from outlet before putting on or taking off parts.
Close supervision is necessary when used by or near children, or disabled people.
Use this furnishing only for its intended use as described in these instructions.
Do not use attachments not recommended by the manufacturer.
Never operate this furnishing if it has a damaged cord or plug, if it is not working
properly, if it has been dropped or damaged, or dropped into water.
Keep the cord away from heated surfaces.
Never drop or insert any object into any opening.
Do not use outdoors. Just for household indoor use only.
To disconnect, turn all controls to the off position, the remove plug from outlet.
WARNING: Risk of injury - Keep children away from extended foot support.
WARNING: Risk of injury to Persons – do not use this furnishing to support video
equipment such as televisions or computer monitors.
When not in use, it is recommended that the wand be stored securely in the
pocket on the outside of the arm.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
SAVE THESE INSTRUCITONS.
In a double-insulated product, two systems of insulation are provided instead
of grounding. No grounding. No grounding means is provided on a double-in-
sulated product, nor is a means for grounding to be added to the product.
Servicing a double-Insulated Product requires extreme care and knowledge of
the system, and is to be done only by qualified service personnel. Replace-
ment parts for a double-insulated product must be identical to the parts they
replace.
SERVIVING OF DOUBLE- INSULATED PRODUCTS.

Page 3
Connect the Headrest and Lumbar cable plugs (Figure C). Headrest-only
modelshave only one set of cables.
Slide inside back receivers onto the steel mechanism posts in the base of the
chair. (Figure A)
To remove the back from the base, use a screwdriver pressing outward on
the black tab in the metal receivers on both sides of the chair back and lift the
back from the base of the chair to release. (Figure B)
CAUTION: PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING ASSEMBLY
PROCESS. IT IS RECOMMENDED TO USE TWO PEOPLE WHEN ASSEMBLING AND
REMOVING THE INSIDE BACKS TO AND FROM THE BASE OF THE FURNITURE.
Press both sides of the back firmly into place until the back automatically
locks into track.
STEP1:
STEP2:
STEP3:
STEP4:
Connect the power cord. STEP5:
CHAIR ASSEMBLY
ATTACHING THE CHAIR BACK TO THE CHAIR BASE
Back Receivers
Steel
Figure C
Figure A
Figure B
Figure 5
Screwdriver required (not included)
Headrest
Appuie - tête
Reposacabezas
Lumbar
Lombaire
Lumbar
Mechanism
Post

Page 4
HEADREST
CLOSE CLOSE
& HOME
CLOSE OPENOPEN OPEN
LUMBAR FOOTREST
USB
To recline: Sit on the furniture, and press the front of the button closest to the
footrest to smoothly raise the footrest and recline to any position. To lower the
footrest and return to an upright position, press the back side of the button clos-
est to the footrest.
To adjust headrest: Press the front of the button closest to the backrest to
smoothly raise and adjust the headrest to any position. To lower the headrest and
return it to its original position, press the back side of the button closest to the
backrest.
To adjust lumbar support: Press the front of the center button to smoothly raise
and adjust the lumbar support to any position. To lower the lumbar support and
return it to its original position, press the back side of the center button.
To close all: To simultaneously return the headrest, footrest, and lumbar support
to their original positions, press and hold the back side of the button closest to the
footrest.
Product Protected By Following Patents:
Patented Articulating Power Headrest & Lumbar
US Patent: 10,736,423
OPERATING INSTRUCTIONS FOR TRIPLE POWER SKU’S

Page 5
Confirm the wire from
chair to transformer is
firmly connected
Chair doesn't recliner or lift
Headrest or lumbar motor
wires may not be
connected well inside back
flap of chair
Check the headrest
and lumbar motor
wires have been
correctly connected
Headrest or Lumbar doesn’t
work
Headrest and lumbar
motor plug have been
cross connected
Check the headrest and
lumbar motor wires
(labeled) have been
correctly connected
Headrest and lumbar work
oppositely
Side switch may not be
connected well
Check the side switch cord
has been correctly
connected to plug
The side switch doesn’t work
Transformer may not be
connected well
Check the power supply
has been correctly
connected to
transformer and socket
00473 REV A

•NOTE: This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
by the party responsible for compliance could void user's authority to operate the equipment.
Customer Service
If you have any questions regarding the use of this unit,or find that your unit needs service, please
contact your retailer.