ROOMS TO GO SYNE K2111-85PHR-Air User manual

Assembly Instructions
SYNE K2111-85PHR-Air Recliner w/power Headrest, Air Massage
SKU# 15721156 / 15721170
Manufactured for Rooms To Go
***CAUTION: The item is heavy, assembly should be performed by two people in soft surface.
Parts# Desc. Pattern Q'ty Parts# Desc. Pattern Q'ty
A Wash 4 pieces B Butterfly
nut 4 pieces
CBolt (M8*3.14"，18 threads per
inch) 4 pieces D Transfor mer 1 pieces
Figure 1
Figure 2
Figure 3 Figure 4
1) The bolts package with a sticker "Hardware" is attached to the bottom of base rail.(See Figure 1)
2) Attached each bolt to corresponding pre-drilled holes by hand turning on clockwise direction as figure underneath.
(See Figure 2) Please attached to Screw the shorter threaded end of the bolt into the armrest and follow the arrow
direction to Insert the longer threaded end of the bolt into the hole in the base (Figure 3).
3) Please place the washers and Butterfly nut into the bolt as show by hand and then turning in clochwise direction until
it is tight.(See Figure 3)
D
C
D
A
B
A
B
C
D
P
D
C
P
C
C
D
C
D
P
C
D
A
B
P
A
B
C
D
A
B
A
B
D
C
D
A
B
A
B
C
D
P
D
C
P
C
C
D
C
D
P
C
D
A
B
P
A
B
C
D
A
B
A
B
D
C
D
A
B
A
B
C
D
P
D
C
P
C
C
D
C
D
P
C
D
A
B
P
A
B
C
D
A
B
A
B
C
D
P
C
D
A
B
P
A
B
C
D
C
D
A
B
A
B
A
B
A
B
C
D
P
D
C
P
C
D
C
D
C
D
P
C
D
A
B
P
A
B
C
D
C
D
A
B
A
B
A
B
A
B
C
D
P
D
C
P
C
D
C
D
C
D
P
C
D
A
B
P
A
B
C
D
C
D
A
B
A
B
A
B
A
B
C
D
P
D
C
P
C
D
C
D
C
D
P
C
D
A
B
P
A
B
C
D
C
D
A
B
A
B
A
B
A
B
C
D
P
D
C
P
C
D
C
D
Front

E
F
E
F
E
F
C
D
A
B
A
B
C
D
C
D
A
B
A
B
C
D
D
C
G
H
A
B
C
D
E
F
E
E
F
F
G
H
I
E
F
E
F
C
D
A
B
C
D
Step3
Locate the power cord C attached to the
bottom back and connect to plug D
Step 2
Slide the metal receiver over the
metal post.Press both sides of
back firmly downward until
locked in place.
A
B
A
B
C
D
C
D
A
B
C
D
A
B
A
B
C
D
C
D
A
B
C
D
A
B
A
B
C
D
C
D
A
B
C
D
A
B
A
B
C
D
C
D
A
B
C
D
Step 5
The Transformer is
attached to the bottom of
rail and connect to DC Port
located at the rear of arm.
Step 4
Locate the power cord E attached to
the bottom back and connect to plug
Step 1
Please located the hand controller at
the beside of metal bracket.
A
B
A
B
C
D
D
C
E
F
E
F
Note: Make sure all PLUGS are connected on the
product before plugging power cord into power
outlet. If not damage can occur.
The USB ports (where applicable) are designed
with working voltage of 5V, and can NOT be used
to supply power for laptop computers (neither PC
or Mac). Plugging a laptop computer to the USB
port may end up damaging either the computer or
the USB port due to unmatched working voltage.