Rosewill PB120-RGB User manual

1
Product Overview
Thank you for purchasing a Rosewill Liquid CPU Cooler.
Please read the instruction manual before use and retain for future reference.
PB120-RGB
Accessory Kit
x1
Liquid CPU Cooler
* The apperance of product is subject to practicality.
x1
Intel Clip
(Pre-Installed)
x1
AMD Clip
x1
Remote
Controller
x4
Gasket
for Backplate
x1
RGB Hub
x1
Insulating Sheet
x1
RGB Fan
x4
LGA 2011
Screw
x1
Thermal
Grease
x1
Backplate
x1
SATA Cable
x1
3 Pin Connector
Cable
x4
Stand-Off
Cylinder
x4
Spring Screw
x4
M3.5x31 Screw
for Backplate
x4
#6-32x6 Screw
for Radiator
x4
#6-32x29.5 Screw
for Fan

2
Installation Guide
1. Install the Fan and
Radiator into PC Case
1-1. Secure fans on radiator with
four #6-32x29.5 mm screws
(Figure 1).
1-2. Secure installed radiator in the
case with four #6-32x4 mm
screws.
2. Instructions for LGA 2066
and 2011
2-1. Conrm the motherboard is LGA
2066 / 2011 platform (Figure 2).
2-2. Secure four LGA 2011 screws into
the corresponding screw holes.
2-3. Apply a proper amount of the
thermal grease on CPU.
2-4. Tear the protector off from the
bottom of water block and place
the installed water block steady
with buckle and LGA 2011 screws
on the cut-out of the motherboard.
2-5. Keep the copper bass plate
touching the CPU as much as
possible and secure water block
temperately on top of LGA 2066 /
2011 with four screws.
3. Instructions for AMD
Water Block
3-1. Uninstall the Intel Clip and nd the
correct AMD buckle as shown in
gure (Figure 3).
3-2. Push buckles straight through the
cut-out to bottom.
1
2
3
#6-32x29.5
Fan Screws
#6-32x4
Radiator Screws
Spring Screws
LGA 2011 Screws
CPU
Motherboard
Buckie
Cut-Out
AMD Clip
* The apperance of product is
subject to practicality.

3
4. Instructions for AMD / Intel
4-1. Conrm the motherboard and match the correct side of backplate (AMD / Intel) (Figure 4).
4-2. Find the screw holes and secure four M3.5x31 screws in. Please note the scramble of
dummy-proof between stand-off and M3.5x31 screws.
4-3. Insert the installed backplate on the back of the motherboard and secure the stand-off
from the other side.
4-4. Apply a proper amount of the thermal grease on CPU.
4-5. Tear the protector off from the bottom of the water block and place the installed water
block steady with buckle and M3.5x31 screws on the cut-out of motherboard.
4-6. Keep the copper bass plate touching the CPU as much as possible and secure water block
temperately on top of M3.5x31 screws with four spring screws.
5. Connect Power to the Water Pump
Activate water cooler by plugging the conducting
wire into the consistent CPU_FAN or CPU_OPT pin
header (Figure 5).
4
5
AMD Intel
Spring Screws
AMD / Intel Clip
Stand-Off Cylinder
CPU
Motherboard
Insulating Sheet
Backplate Gasket
Backplate
M3.5 x 31
Backplate Screw
Dummy-Proof
Dummy-Proof
CPU_FAN

Technical Support Information [email protected] 1-800-575-9885
Please register your product at www.rosewill.com for complete warranty information and support for your product. PB120-RGB_A
6. Connect the RGB Hub
6-1. Connect the fan cable and water block cable into the RGB fan hub slot labeled “Fans”.
6-2. Plug the 3-pin connector cable to the addressable 5V* RGB header of your motherboard
and other end to M/IN on hub as another control option for system synchronization.
6-3. Connect the power cable to the RGB fan hub and connect the other end to your power
supply.
6-4. Mount the RGB fan hub to a desired location within the system via the magnet attached on
the back of the RGB fan hub (Figure 6).
7. Remote Control
To switch remote controller to
motherboard synchronization,
press the remote control’s “ON”
button. Press “ON” again to
return back to remote control
(Figure 7).
Power
Supply
M/B
Addressable
RGB Header
Switch On Between Remote
Control and Motherboard Control
Programmed Lighting Effects
Single Color Options
Low / Medium / High Fan Speed
LED Switch Off
Increase Brightness / Decrease
Brightness / Cycle Through Single
Color Options
Caution
To avoid damage during installation, connect the case fan to the included fan hub only.
Do not connect fans directly to any motherboard.
*12V RGB headers are not supported
6
7