Rosewill RCX-Z4 User manual

user manual
COOLER RCX-Z4

1
user manual
COOLER RCX-Z4
Improper Installation will result in damage to the processor.
Never switch on the computer system until the fan is connected
on to the motherboard power connector.
!WARNING

AX 5 BX 5 CX 1
Installation Components
DX 2 EX 2 FX 1
GX 8 HX 2 IX 2
JX 4 KX 6 LX 1
MX 4 NX 4 OX 2
2
user manual
COOLER RCX-Z4

AMD K8 / AM2 Installation
1
Remove the retention module
from the motherboard by
removing the screws.
Keep the original motherboard
backplate as it is.
2
NOTE
The K8 / AM2 heatsink retention bracket have been pre-installed on the
heatsink. Do not remove for K8 / AM2.
3
user manual
COOLER RCX-Z4

Stick the protective insulated
film onto the back of the heatsink
retention brackets.
3
4
O
Apply the proper amount of
thermal compound on the CPU
surface, a thin film is ideal, extra
thermal compound will not
improve performance.
Make sure the CPU surface is
perfectly clean.
FOR AMD K8
Place the RCX-Z4 on the top of the CPU, align two holes ( shown in red
as the picture below ) of heatsink retention bracket with the Motherboard holes.
Using the K8 screws with
spring inserted, screwing
down into the motherboard
backplate.
I
H
D
4
user manual
COOLER RCX-Z4

Place the RCX-Z4 on the top of the
CPU, align two holes ( shown in
red as the picture below ) of
heatsink retention bracket with the
Motherboard holes.
Using the K8 screws with
spring inserted, screwing down
into the motherboard backplate.
See page 10-11 for the backplate fan
controller and fan Installation
5
user manual
COOLER RCX-Z4
FOR AMD-AM2
The RCX-Z4 is now installed on your K8-AM2 CPU
M
D
N

Remove the fan from the sink by
unscrewing the four black screws.
Take off the pre-attached pair of
K8-AM2 heatsink retention
bracket; keep the four screws
for the next
6
user manual
COOLER RCX-Z4
E
INTEL P4 LGA775 Installation
1
2
Attach both of the LGA775
heatsink retention brackets
to the heatsink base.
3

Place the screws through the
backplate into the head thread
of the screws , make sure the
correct four holes are used, as
shown in the diagram highlighted
with red. Follow the same
procedure for all four screws.
7
user manual
COOLER RCX-Z4
Put the backplate with the screws
fixed through the four
motherboard holes as illustrated.
Stick the protective insulated film
onto the back of the heatsink
retention brackets.
4
5
6
C
J
F
K
K
F
J

Secure the backplate onto the
motherboard by using the four
collars nuts . Turn these
down onto the insulation washer,
do not tighten one first, work
around all four, gradually
tightening them all.
8
user manual
COOLER RCX-Z4
Put the four rubber pads on
top of the four screws .
Place the insulation washer
over the screws so they sit on the
motherboard as shown. Follow the
same procedure for all four screws.
7
8
9
B
G
G
A

Place the cooler onto the four
screws, secure the cooler with
four more collars .
9
user manual
COOLER RCX-Z4
Screw the fan onto the heatsink
using the four black screws.
Apply the proper amount of
thermal compound on the CPU
surface, a thin film is ideal, extra
thermal compound will not
improve performance.
Make sure the CPU surface is
perfectly clean.
10
11
12
G
H
See page 10-11 for the backplate fan
controller and fan Installation
The RCX-Z4 is now installed on your INTEL LGA 775 CPU