Royalcraft Malaga 110cm Round Table User manual

ProducedinChinaforAMir&Co.,Ltd.
© A Mir & Co., Ltd. 2 / 5
www.a-mir.co.uk
Before you start
Warnings
IMPORTANT, RETAIN FOR FUTURE REFERENCE
READ CAREFULLY
See enclosed instructions for assembly, safety and care
information.
Failure to follow the warnings could result in serious injury.
Handle heavy parts with care.
Ensure that this product is fully assembled as illustrated before
use.
This product should only be used on firm, level ground.
Keep small parts out of reach of children.
Do not stand or climb onto this product.
This product is intended for domestic use only.
Furniture can be dangerous if incorrectly used. No liability will be
accepted for damage or injury caused by incorrect use of this
product.
This table is not intended to support a parasol separately. A
parasol base with suitable weight must be used to support
your parasol.
Dos
When you are ready to start, make sure that you have the right
tools, plenty of space and a clean, dry area for assembly.
Removing all packaging and banding and place the components
carefully on suitable surfaces to prevent damaging or scratching
them.
Check the pack and make sure you have all of the parts listed.
Check all screws and bolts are tightened and inspect regularly.
We recommend the use of furniture covers to protect your product
when not in use.
This product is suitable for all year outdoor use.
However to prolong its life we recommend that during severely
bad weather and during the winter months, it is stored in a cool,
dry place.
Before storage, ensure that the product is clean and dry.
To clean, wipe down with a sponge and warm soapy water and
wipe with a clean, dry cloth.
Don’ts
Do not use scourers, abrasives, washing powders, chemical cleaners
or any other substances containing abrasives since these substances
can damage the product, including the glass panel.
Do not place very hot or very cold items on the glass surface
unless adequately thick table-mats are used to prevent such
items from coming into contact with the glass.
Do not use the glass as a chopping surface. Do not strike glass
with hard or pointed items.
Do not strike the glass with hard or pointed items.
Do not use power tools to construct this product.
Do not use this product if parts are missing, damaged or worn.
Do not sit or lean on this product.
Do not stand or climb onto the product and do not use it as a ladder,
as this could lead to it unbalancing and overturning.
Never drag furniture when moving it, always lift it.
Number of people required for assembly
Two people.
Time to assemble
30 Minutes
Tools required
Tips:
Do NOT fully tighten bolts before
all components are connected.
Only fully tighten once you are
satisfied with the alignment of all
components.
Do not overtighten bolts.
Malaga 110/140cm Round Table
Assembly Instructions

ProducedinChinaforAMir&Co.,Ltd.
© A Mir & Co., Ltd. 3 / 5
www.a-mir.co.uk
Components, fixtures & fittings (not actual size)
Parts List
Part
No. Diagram Qty Part No. Diagram Qty
A
Table Top Frame
1 PC B
Leg
2 PCS
C
Connecting Panel
2 PCS D
Glass Top
1 PC
E
Bolt Head Cap
12 PCS F
M6 Bolt
12 PCS
G
Washer
12 PCS H
Spacer
8 PCS
I
Spanner
1 PC
Malaga 110/140cm Round Table
Assembly Instructions

ProducedinChinaforAMir&Co.,Ltd.
© A Mir & Co., Ltd. 4 / 5
www.a-mir.co.uk
Step by step assembly instructions
Step One
Open the packaging with the glass face down on a flat surface. Leave the glass on the carton
until the rest of the table is fully assembled.
With the help of another person, place Table Top Frame (A) upside down on a flat,
non-abrasive surface to avoid scratching the table surface or rim.
Step Two
Do NOT assemble the Legs (B) to the Table Top Frame (A) while it is still resting on the
Glass Top (D).
Loosely attach the Table Legs (B) to the Table Top Frame (A) using Washers (G) and
Bolts (F).
Malaga 110/140cm Round Table
Assembly Instructions

ProducedinChinaforAMir&Co.,Ltd.
© A Mir & Co., Ltd. 5 / 5
www.a-mir.co.uk
Step Three
Loosely attach the Connecting Panels (C) onto the Table Top Frame (A) and Table Legs (B),
aligning all holes in each part, using Spacers (H), Washers (G) and Bolts (F).
Only tighten the bolts when all bolts and washers are in place. Once you are satisfied with the
alignment of the components carefully tighten all bolts using Spanner (I).
Do not over-tighten.
Cover each bolt with Bolt Head Cap (E).
Step Four
With the help of another person, carefully turn the table in the upright position. Level the table
by adjustable feet screw.
Carefully place the Glass Top (D) on the Table Top Frame (A) and make sure they are aligned.
There are plastic suction caps pre-fitted onto the table top, make sure the glass top is in full
contact with the plastic suction caps.
Your table is now ready for use.
Note: This table is not designed to hold the parasol separately.
Parasol base with suitable weight should always be used.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
Adjustable Foot Screw
Malaga 110/140cm Round Table
Assembly Instructions