RP LIGHTING 1060 User manual

Models: 1060, 1060LED
Model No. 1060 net weight: 6.5 kgs(14.3 lbs)
Model No. 1060LED net weight: 6.8 kgs(14.96 lbs)
READ AND SAVE THESE INSTRUCTIONS
INSTALLATION MANUAL
Ceiling Fan

/ UNPACKING FAN

1
READ AND SAVE THESE INSTRUCTIONS.
IMPORTANT SAFETY INFORMATION
1. Read all instructions and safety information carefully before installing your fan and save this manual.
2. All electrical connections must be in accordance with the National Electrical Code ANSI/NFPA70 and local electrical code.
If you are unfamiliar with proper electrical wiring connections, contact and obtain the service of a qualified licensed
electrician.
3. To reduce the risk of electric shock, turn the electricity off at main fuse box or circuit breaker before beginning fan
installation or servicing the fan. Do not operate fan without blades.
4. To reduce the risk of injury to person, make sure a location selected for the fan allows clear space for blades to rotate,
and at least seven(7) feet (2.1 Meters) of clearance between the floor and the fan blade tips.
CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges.
WARNING: To reduce the risk of fire, electric shock or personal injury, mount the fan to outlet box marked
ACCEPTABLE FOR FAN SUPPORTS of 15.9 kgs(35 lbs) or less, and use mounting screws provided with the
outlet box. Most outlet boxes commonly used for the support of luminaires are not acceptable for fan support and may
need to be replaced. Consult a qualified electrician if in doubt.
5. To reduce the risk of persona injury, use only approval hanging bracket, those parts and screws supplied with the fan
and or accessories designated specifically for use with the fan.
WARNING: Using parts and or accessories other than those supplied with the fan could result in personal injury or
property damage and will void the warranty.
6. After completing installation, check all set screws and make sure they are firmly secured.
7. Electrical diagrams are for reference only. Light kits are not packed with the fan must be UL or ETL listed and marked
suitable for use with the fan you are installing.
Choose fan and light switches must be UL or ETL general use. Refer to the instructions packaged with the light kits
and switches for proper assembly and installations.
8. Wooden blades are not intended for storage or installation in spaces that are not temperature controlled.
To avoid issues with blade warping, do not store or install ceiling fans in areas without air conditioning.
9. Do not operate reversing switch while fan blades are in motion. Fan must be turned off and blades stopped before
reversing blade direction.
10. Do not use water or detergents when cleaning the fan or fan blades. A dry cloth or lightly damped cloth will be suitable
for most cleaning.
WARNING: To reduce the risk of fire or electric shock, do NOT use this fan with any solid-state speed control device.
WARNING: To reduce the risk of personal injury, do NOT insert foreign objects in between rotating fan blades.
WARNING: To reduce the risk of electric shock, disconnect the electricity supply circuit to the fan before installing light kit.

2
Model No. 1060
Parts List
8. Hardware bag included:

Model No. 1060LED
Parts List
3
8. Hardware bag included:

4

5

6
2
Notch
Tab
Carefully lift the fan motor assembly onto the mounting bracket
that was attached to the outlet box.
Turn the entire assembly until the check tab(stopper of bracket)
dropped into the notch of the downrod ball and seats firmly.
Note: The entire fan motor assembly should not rotate when
seated properly.
WARNING: Failure to seat tab in the notch of the hanging ball
could cause damage to electrical wire and possible shock or fire
hazard.
WARNING: To avoid possible shock, do not pinch wires between
the downrod/ hanging ball assembly.
WARNING:

NOTE: The wiring diagram includes the light kit wiring.
The light and light switch wiring is omitted when no light kit is used with the fan.
7

9
WARNING:
Fibber Washers
& Blade Screws
Installation
Hole
Locate blade attachment screws and washers in the hardware pack.
Slide blade through one of the slot openings on motor housing, aligning holes in blade with holes
on the flywheel. Be sure to note label on blade indicating “THIS SIDE UP”.
Securely attach each blade with three(3) screws & (3)washers using Phillips screwdriver, make sure 3 screws
are tightened evenly. NOTE: DO not overtighten the screws as it could damage the blades.
Repeat this process for the remaining blades.
Locate 2 screws on the underside of the mounting
bracket. Attach canopy to the mounting
bracket by placing screws into the keyhole slots.
Rotate the canopy so that the mounting
screws slide into the narrow ends of the keyhole
slots. Tighten the screws firmly.
DO NOT place fan on a flat surface once the
blades are attached to the motor.
This will cause the blades to become unbalanced
and result in a wobbling fan.
To reduce the risk of personal injury, do not bend
the blade brackets (also referred to as flanges)
during assembly or after installation.
DO NOT insert objects in the path of the blades.

11
SUMMER
DOWN DRAFT
WINTER
UPDRAFT
Counter Clockwise Rotation Clockwise Rotation
chain(s) located in the switch housing.

12

RP-12162021