Rubine RCF-ECO-5BL User manual

56"
CEILING FANS
Instruction Manual
SAFETY GUIDELINES AND INSTALLATION PROCEDURES
RCF-ECO-5BL
(DC1725-501-BC)
(DC1725-501-WC)
(DC1725-501-MB)

COMPONENTS SCREW PACKAGE
WHAT YOU HAVE
Please checkout following parts after opening the box
Page 1
PARTS QUANTITY SCREW PACKAGE QUANTITY
2. TOP CANOPY
3. COUPLING COVER
5. DC MOTOR WITH RECEIVER
6. FLY WHEEL
7. LIGHT KIT PLATE WITH LED
8. GLASS SHADE
9. BLADES
1
1
1
1
1
1
1
1
COMPONENTS SCREW PACKAGE
FAN SIZE VOLTAGE MAX. FAN
POWER
MAX SPEED
(RPM)
56"9.08kgs 11.16kgs
160±10%
47.7W
220~240V/50Hz
1. DOWNROD
(WOBBLE-FREE ASSEMBLY)
PRODUCT
WEIGHT
CARTON
WEIGHT
4. TOP HOUSING COVER
10. TRANSMITTER WITH 12V
BATTERY, HOLDER AND
2 MOUNTING SCREWS
5
1
11. BLADE HOLDER SCREWS
12. BLADE ATTACHMENT SCREWS
14. EXPANSION J HOOK
21
2
1
13. HEX-HEAD SCREWS
6
1
2
3
4
5
7
8
9
11
12
13
14
6
10
17
16
15
15. MOUNTING RING
17. FLAT HEAD SCREWS
16. LOCK WASHER SCREWS
3
3
1
LED LIGHT
POWER
17W

Page 2
Double pole single throw switch(Breaker Switch)
Earth
Ceiling Fan
Wall Switch (OFF/ON)
240VAC/50Hz
Power Supply
8 ) This product is not provided with cord, plug or other means for disconnection from the
supply. Connecting or changing power cord or lead wire, must be done by qualified
personnel in order to avoid hazard.
9 ) This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
10 ) Children should be supervised to ensure that they do not play with the appliance.
11 ) The appliance is fitted with means for disconnection from the supply mains having a
contact separation in all poles that provide full disconnection under overvoltage category
III conditions, and these means must be incorporated in the fixed wiring in accordance
with the wiring rules.
B ). SAFETY GUIDELINES
1 ) Please do not install the ceiling fan at high humidity areas.
2 ) Distance between fan blades and ground must be at least 2.3 meter and above.
3 ) Do not touch fan blades with any objects when the ceiling fan is spinning.
4 ) To minimize the chances of electrical shock, power switch must be OFF before installing
or dismantling the ceiling fan or any electrical wiring connection.
5 ) All electrical connections must conform to the national electrical safety codes. To prevent
electrical shock, earth wire must be installed correctly (suitable for power supply of
240V AC/50Hz).
6 ) To ensure your personal safety and optimize functions of the ceiling fan, assembly and
installation by qualified technician is highly recommended.
7 ) Only direct connection to wall switch is allowed. Please refer to diagram below.
WARNING
A ). TO ENSURE YOUR PERSONAL SAFETY, PLEASE READ THROUGH THE
INSTRUCTION MANUAL BEFORE USE
1 ) Do not bend the blade holders during installation, blades balancing or fan cleaning.
2 ) To prevent accidents, power switch must be OFF before ceiling fan installation.
3 ) Ceiling fan installation and electrical wiring must be done by qualified technician in
accordance with all applicable codes and air conditioning engineers (ASHRAE) or the
local qualified authorities.
4 ) Be cautious when drilling the wall to avoid damaging electrical wiring and other hidden
parts.
5 ) Ceiling fan must be hooked on concrete ceiling. Do not install the ceiling fan on plaster
ceiling or any types of drywall ceilings. During ceiling fan installation, all screws must be
tightened at all allocated parts.

Page 3
INSTALLATION PROCEDURES
Before ceiling fan installation, please go through the procedures in
detail with picture diagrams as reference.
STEP 1 (See Diagram 1)
1) Attach the fly wheel to motor.
2) Align fly wheel screw holes with motor
screw holes.
3) Install blade holder screws in the screw
package.Tighten up all the screws.
STEP 2 (See Diagram 2)
1) Install fan blades to the fly wheel.
2) Align the screw holes on the fan blade
and fly wheel.
3) Tighten up 2 blade attachment screws on
the bottom of the fly wheel.
4) Then tighten up 2 blade attachment
screws on the top of the fly wheel.
5) Repeat same step on all the remaining
fan blades.
DIAGRAM 1
Screw
Motor
Fly Wheel
DIAGRAM 2
Fly Wheel
Fan Blade
Screw (Bottom)
Screw (Top)
STEP 3 (See Diagram 3)
1) Attach the top housing cover to the
motor coupling and align the 3 small screw
holes on the top housing cover.
2) Attach the mounting ring to the top
housing and align the 3 big screw holes on
the top housing cover.
3) After all the 6 screw holes are aligned,
tighten the top housing cover and mounting
ring and motor coupling by using the 3 flat
head screws and 3 x lock washer screws
provided in the hardware package.
DIAGRAM 3
Top Housing
Cover
Mounting Ring
Small Screw Hole x3
(Lock Washer Screw)
Motor
Coupling
Big Screw Hole x3
(Flat Head Screw)

Page 4
WARNING:
Installation without proper procedures as above mentioned might result to fan loosening and
falling.
STEP 4 (See Diagram 4)
1 ) Remove the 1st hex-head screw
along with the fixings (pin, metal nut,
lock washer and metal washer) from the
downrod.
2 ) Remove the pin on 2nd hex-head
screw and loosen the other fixings.
STEP 5 (See Diagram 5)
1 ) Loosen the screw on the top canopy.
2 ) Insert the downrod through top
canopy and coupling cover.
3 ) Thread the safety cable through the
downrod.
4 ) Connect both connectors from the
downrod and fan motor.
5 ) Lock the downrod to the motor
coupling, tighten up with 2 hex-head
screws and fixings.
6 ) Tighten 2 screws on the motor
coupling.
7 ) Slide down the coupling cover until it
rest on top housing cover.
DIAGRAM 4
DIAGRAM 6
STEP 6 (See Diagram 6)
1 ) Lift the wobble-free assembly onto
the mounted hook.
2 ) Install the 1st hex-head screw
together with fixings.
3 ) Tighten up the 2nd hex-head screw
and fixing.
4 ) Tighten the 2 screws in the middle of
wobble-free assembly.
Note:-
1. Remember to lock the pin after
tightening hex-head screws.
2. Hook must be installed on concrete
ceiling.
DIAGRAM 5
Safety Cable Connector
Top Canopy
Coupling Cover
Screw x 2
Hex-head Screw
Motor Coupling
The 1st Hex-head Screw
Pin
Metal Nut
Lock Washer
Metal Washer
The 2nd Hex-head Screw
Pin
Terminal Block
Fixings
Screw (Loosen)
Wobble-free
Assembly
2 Screws in the middle
(Tighten)
Hook
The 1st
Hex-head Screw
The 2nd
Hex-head Screw
Metal Washer
Pin
Metal Nut
Lock Washer
Fixings
Downrod

STEP 7 (See Diagram 7)
DIAGRAM 7
Ceiling
Ceiling
Ceiling Red / Brown Wire
(Incoming LIVE Wire)
Black / Blue Wire
(Incoming NEUTRAL Wire)
Green Wire
(Incoming EARTH Wire)
Terminal Block (marked )“L”
Terminal Block (marked )“N”
FROM TO
Connect wiring as below:-
Page 5
SUPPLY CIRCUIT
EARTH wire
(Green)
NEUTRAL wire
(Black / Blue )
LIVE wire
(Red / Brown)
L
N
Top Canopy
Screw
(Tighten up)
DIAGRAM 8
STEP 8 (See Diagram 8)
Tug the top canopy to ceiling and tighten
up the screw on down rod to secure the
top canopy.
L
N
L
N
Terminal Block (marked )“ ”
From Ceiling From Ceiling From Ceiling

Page 6
STEP 10 (See Diagram 10)
1)
and loosen the other 2 (Do not remove).
2) Place the key hole of light kit plate
through the 2 loosen screws and twist to
lock in place.
3) Tighten up all screws including the one
removed earlier.
4) Connect the white and black wire
connector from fan motor to connector from
LED .
5) Re-install the LED to the light kit plate.
Remove 1 screw from the mounting ring
STEP 9 (See Diagram 9)
Remove the LED by removing the 3 screws
from the light kit plate.
STEP 11 (See Diagram 11)
Install the glass shade by twisting tightly.
DIAGRAM 9
Light Kit Plate
LED
DIAGRAM 11
Glass Shade
DIAGRAM 10
Light Kit Plate
LED
Black Wire
Connector
Black Wire
Connector
Screw
Mounting Ring
White Wire
Connector
White Wire
Connector
Key Hole

SAFETY TIPS:
Please ensure the distance between fan blades and ground
must be at least 2.3 meter and above.
WARNING!
FA ST E N T H E S A F E T Y C A B L E TO T H E M O U N T E D
EXPANSION J HOOK FOR SAFETY PURPOSES.
Page 7
GROUND
MIN 2.3m

56"
吊 扇
安 装 手 册
安全注意事项和安装程序
RCF-ECO-5BL
(DC1725-501-BC)
(DC1725-501-WC)
(DC1725-501-MB)

56"
1
1
1
1
1
1
1
1
5
1
1
2
3
4
5
7
8
9
11
12
13
14
6
10
17
16
15
21
2
1
6
3
3
1
配 件 明 细
拆箱后，请逐一清点以下零件
零件 数量 数量
配件包
1. 吊杆（吊挂系统）
2. 吊盅
3. 接头盖
5. DC马达附接收器
6. 中圈
7. 灯盘附 灯LED
8. 玻璃灯罩
9. 叶片
10. 发射器附1粒电池 ,壁座
和2颗螺丝
4. 马达上罩
11. 叶架螺丝
12. 叶片螺丝
13. 螺栓
14. 安全J勾
15. 补强板
17. 伞头螺丝
16. 带弹介螺丝
元 件 配 件 包
尺寸 电压/频率 风扇最大功率 最大转速 净重 毛重
1
9.08kgs 11.16kgs
160±10%
47.7W
220~240V/50Hz
LED灯功率
17W

2
接地
吊扇
墙开关（关/开）
240V/50Hz供电
双柱单掷开关（断路开关）
警 告
A) 为了确保您的人身安全，使用前请详细阅读说明书
1. 在安装叶架，平衡叶片或清洁风扇的时候，不能将叶架弯曲。
2. 安装此吊扇前必须关闭电源开关，以免造成意外。
3. 此吊扇的安装和接电应由技术熟练的电工完成。
4. 注意钻墙的时候不要损坏电线和其它隐藏的零件。
5. 吊扇必须悬挂在坚定稳固的天花板上面，吊扇安装时，各部分螺丝必须锁牢。
B）安全注意事项
1. 请不要将吊扇安装在潮湿的地方。
2. 安装吊扇时，叶片至少离地面2.3米高处，以防与叶片发生意外碰触。
3. 吊扇运转时，请不要用任何物品碰触叶片，以免危险。
4. 为了减少触电事故发生，安装电线或拆装风扇前请及时关电源开关。
5. 所有的接电必须符合国家安全要求的标准，为了避免意外触电，确保吊扇接地线生效
（适用于240V供电）。
6. 为了确保您的安全和产品的使用达到最佳效果，建议要技术熟练的技工来安装此风
扇。
7. 只允许直接连接墙开关，请参考下图。
8. 本产品没有提供插头或其他绝缘体，连接或更换电线的时候，建议请资深的技工操
作，以免造成危险。
9. 本产品不打算由这些人（包括儿童）来使用：身体上，感觉上或者精神上有缺陷者，
或缺乏经验和知识者。除非他们得到了在对其安全负责的人关于该项产品使用的监护
或指导（对所有产品）。
10. 儿童应当受到监督以确保其不会玩耍器具（对所有产品）
11. 本产品已配有双极断开装置(过电压等级III条下)，按布线规则，其连接的固定布线必
须配有这样的断开装置。

3
步骤1（图1）
1）把中圈装到马达上。
2）对准中圈和马达上的螺丝孔。
3）用配件包里的叶架螺丝把中圈固定，
锁紧所有螺丝。
步骤2（图2）
1）把叶片装到中圈上。
2）对准叶片和中圈上的螺丝孔。
3）用叶片螺丝从中圈底部把叶片底部固
定。
4）再锁叶片上面的螺丝。
5）按以上步骤安装剩余叶片。
安 装 程 序
为了确保顺利安装此吊扇，请详细阅读以下步骤，并参照插图。
图1
螺丝
中圈
马达
图2
叶片 中圈
螺丝（上部）
螺丝（下部）
步骤3（图3）
1）安装马达上罩的马达接头，并使马达
上罩的3个小螺丝孔对齐马达接头上相对
应的螺丝孔。
2）安装补强板到马达上罩，并使补强板
上的3个大螺丝孔对齐马达上罩上相对应
的3个大螺丝孔。
3）所有螺丝孔一一对齐后，用螺丝包提
供的3个伞头螺丝和3个带弹介螺丝包补
强板和马达上罩琐紧在马达接头上。
图3
补强板
小孔x3
带弹介螺丝
马达
上罩
大孔x3
伞头螺丝
马达
接头

4
步骤4（图4）
1）把吊杆上第一个螺栓和其他 一
起拆下（R销，螺母，弹介和平华
司）。
2）把第二个螺栓上的R销拆下，松开
其他配件。
配件
步骤5（图5）
1）松开马达接头上的2颗预锁螺丝。
2）将吊杆穿入吊盅和接头盖。
3）将安全钢索穿过吊杆。
4）把马达上的接线套接到吊杆的接线
套上。
5）将吊杆套入马达接头处，对准孔，
用配件包里的螺栓锁上。
6）锁紧之前松开的螺丝。
7）把接头盖移至马达的上端。
步骤6（图6）
1）将吊扇挂上已装紧的吊钩上。
3）拧紧第二个螺栓上的配件。
4）拧紧吊挂系统上的2颗螺丝。
2）装上之前拆下的第一个螺栓和其他
配件。
注意：-
1. 记得插上R销
2. 吊钩必须安装在坚固的天花板上
如 果 没 有 按 照 上 面 指 示 把 吊 杆 装 紧 ， 有 可 能 会 导 致 吊 扇 下 坠 。
警 告
图4
图6
吊钩
第2个螺栓
第1个螺栓
R销
螺母
弹介
平华司
吊挂系统
螺丝（锁紧）
吊盅
接头盖
安全钢索
螺丝 x 2
马达接头
螺栓
接线套
图5
R销
螺母
弹介
平华司
R销
第2个螺栓
端子台
第1个螺栓
配件
螺丝（松开）
配件
吊杆

5
L
N
步骤8（图8）
把吊钟移至吊杆上端，使吊钟与天花
板贴紧，锁紧螺丝并把吊钟固定。
步骤7（图7）
红色 / 棕色（天花板火线）
天花板
天花板
天花板
端子台（标注“L”）
绿色（天花板地线）
黑色 / 蓝色（天花板零线） 端子台（标注“N”）
接 线
出 线
接线如下：-
图7
电路图
（红 / 棕色电线）
火线
（黑 / 蓝色电线）
零线
（绿色）
接地线
吊钟
螺丝（锁紧）
图8
L
N
L
N
端子台（标注“ ”）
From Ceiling From Ceiling From Ceiling

6
步骤10（图10）
1）从补强板上取下1颗螺丝，松开另外
2颗。
2）将灯盘上的2个螺丝匙孔对准松开的螺
丝，锁紧螺丝。
3）再将取下的螺丝装上，确保锁紧所有
螺丝。
4）把马达上的白线和黑线接到灯具上的
白线和黑线。
5）再把LED装到灯盘上。
步骤9（图9）
把灯盘上的3颗螺丝拧下，取下LED灯。
步骤11（图11）
装上玻璃灯罩，并拧紧。
LED
图9
灯盘
图11
玻璃灯罩
图10
LED
黑接
灯盘
螺丝
补强板
白线
白线 黑线
螺丝匙孔

7
警 示
为了安全起见，请把安全吊钩装紧在天花板上，再把安全钢丝
挂在吊钩上。
注 意
安全起见，请确保叶片距离地面至少2.3米或以上。
最少 2.3米
地 面