Rubine RCF-Mercury-5BL User manual

52"
CEILING FANS
Instruction Manual
RCF-Mercury-5BL
RCF-Mercury-5BL
SAFETY GUIDELINES AND INSTALLATION PROCEDURES

WHAT YOU HAVE
After opening the box, you should find the following parts:
PARTS QUANTITY SCREW PACKAGE
SCREW PACKAGE
10. PAPER WASHERS 16
11. WIRE NUTS 6
11
9
COMPONENTS
2
3
4
5
6
8
1
7
Page 1
9. BLADE ATTACHMENT SCREWS 16
QUANTITY
12. EXPANSION J HOOK 1
12
7A
10
13
13. BALANCING KIT 1
1. TOP CANOPY
2. DOWN ROD(6”) WITH
HANGING RUBBER WHEEL
3. COUPLING COVER
4. FAN HOUSING & MOTOR
5. GLASS SHADE
6. BLADES
7. REMOTE CONTROL WITH
12 VOLT BATTERY
(RF TRANSMITTER)
7A. REMOTE CONTROL
HOLDER WITH 2
MOUNTING SCREWS
8. RECEIVER
1
1
1
1
1
5
1
1
1
These measures do not include WATTS used by the light kit
FAN SIZE RATING MAX.
POWER
SPEED
MAX. RPM N.W. G.W.
52"11.8kgs 13.0kgs
250+-10%
80W
240V/50Hz

Page 2
A). TO ENSURE YOUR PERSONAL SAFETY, PLEASE READ THROUGH
THE INSTRUCTION MANUAL BEFORE USE:
B). SAFETY GUIDELINES
8) This product is not provided with cord and plug or with other means for
disconnection from the supply. When connect or change the power cord or lead
wire, it must be replaced by the qualified personnel in order to avoid a hazard.
Double pole single throw switch(Breaker Switch)
Earth
Ceiling Fan
Wall Switch (OFF/ON)
240VAC/50Hz
Power Supply
1) Please do not install the ceiling fan at high humidity areas.
2) Distance between fan blades and ground must be at least 2.3 meter and above.
3) Do not touch the fan blades with any objects when the ceiling fan is spinning.
4) To minimize the chances of electrical shock, power switch must be OFF before
installing or dismantling the ceiling fan or any electrical wiring connection.
5) All electrical connections must conform to the national electrical safety codes.
To prevent electrical shock, earth wire must be installed correctly (suitable for
power supply of 240V AC/50Hz).
6) To ensure your personal safety and optimize functions of the ceiling fan,
assembly and installation by qualified technician is highly recommended.
7) Only direct connection to wall switch is allowed. Please refer to figure below.
WARNING
1) Do not bend the blade brackets during the brackets installation, blades
balancing or fan cleaning.
2) To prevent accidents, power switch must be OFF before ceiling fan installation.
3) Ceiling fan installation and electrical wiring must be done by qualified technician
in accordance with all applicable codes and air conditioning engineers
(ASHRAE) or the local qualified authorities.
4) Be cautious when drilling the wall to avoid damaging electrical wiring and other
hidden parts.
5) Ceiling fan must be hooked on concrete ceiling. Do not install the ceiling fan on
plaster ceiling or any types of drywall ceilings. During ceiling fan installation, all
screws must be tightening at all allocated parts.

Page 3
INSTALLATION PROCEDURES
Screw
Blade
Str engt heni ng
Plate
DIAGRAM 1
STEP 1 (See Diagram 1)
Remove the top housing cover by removing the 6
top screws and the strengthening plate. Then
attach the fan blade to the motor assembly by
using the blade attachment screws and paper
washers provided on the screw package, tighten
it securely. Repeat the same step on all the
remaining fan blades.
After all the 5 blades are installed, please re-
install the top housing cover and strengthening
plate using the 6 screws removed previously.
Note: In order to avoid installing the blade in
wrong direction, please pay more attention to
the words “this side up” on the blade.
STEP 2 (See Diagram 2)
Remove safety bolt and pin from down rod.
Loosen the 2 screws for the motor coupling.
Insert the down rod through top canopy and
coupling cover, and then thread the wires through
the down rod. Place the receiver in the top
canopy.
STEP 3 (See Diagram 3)
Slip the down rod into motor coupling, lock it into
place with the safety bolt and pin, and then
tighten the screws. Slide down the coupling cover
until it rests on top of the fan housing.
Before ceiling fan installation, please go through the procedures in
detail with the picture diagrams as reference.
Hangin g Rubber
Wheel
Expansio n J Hook
DIAGRAM 4
DIAGRAM 2
Pin
Safety Bolt
Motor
Coupling
Screw
Top Canopy
Down Rod
Receiver
Coupling
Cover
Screw
Safety Bolt
Down Rod
Coupling
Cover
Motor
Coupling
DIAGRAM 3
Top Canopy
STEP 4 (See Diagram 4)
Life the assembly and hook onto the mounted
Expansion J Hook. Make sure the hanging rubber
wheel seated properly on the Expansion J Hook.
Notice: Expansion J Hook must be installed on
concrete ceiling
WARNING:
Installation without proper procedures as above mentioned might result fan
loosening and falling.

SUPPLY CIRCUIT
Ground
Conductor (Green)
BLUE
BROWN
ORANGE
GREEN
Receiver
(LIGHT)
TO MOTOR L
TO MOTOR N
AC IN N
AC IN L
FOR LI GHT
NEUTRAL wire
(Black / Blue)
LIVE wire
(Red / Brown)
EARTH wire
(Green)
BROWN
BLUE
BLACK
RED
ORANGE
Page 4
STEP 5 (See Diagram 5)
WIRING INSTRUCTIONS FOR FAN MOTOR
There are 4 wires in different colours on top of the motor.
Brown Colour -- Live wire
Blue Colour Neutral wire
Green Colour Earth wire
Orange Colour Light kit wire
--
--
--
a) Connect orange colour wire from fan motor to the receiver orange colour wire
( marked “FOR LIGHT”);
b) Connect brown colour wire from fan motor to the receiver brown colour wire
(marked “TO MOTOR L”);
c) Connect blue colour wire from fan motor to the receiver blue colour wire
( marked “TO MOTOR N”);
d) Connect the incoming LIVE wire (red / brown colour) to the receiver red colour wire
(marked “AC in L”);
e) Connect the incoming NEUTRAL wire (black / blue colour) to the receiver black
colour wire (marked “AC in N”);
f) Connect the green colour wire from fan motor to the incoming EARTH wire
(Green colour)
DIAGRAM 5

Page 5
Light kit
CFL
Glass Shade
Remark:
Compact Fluorescent Light
Bulbs use only
DIAGRAM 7
Top Canopy
Screw
(Tighten up) Down Rod
DIAGRAM 6
STEP 6 (See Diagram 6)
Tug the top canopy to ceiling and
tighten up the screw on down rod to
secure the top canopy.
STEP 7 (See Diagram 7)
Place 2 pcs of 13W E27 bulbs into
the light kit (Bulbs are not included).
Install the glass shade by twisting it
tightly.

Page 6
NOTICE: FOR YOUR PERSONAL SAFETY, PLEASE OBEY
TO THE INSTALLATION PROCEDURES AND
GUIDELINES GIVEN.
WARNING!
FA S T E N T H E S A F E T Y C A B L E TO T H E M O U N T ED
EXPANSION J HOOK FOR SAFETY PURPOSES.

MIN 2.3m
Page 7
SAFETY TIPS:
Please ensure the distance between fan blades and ground
must be at least 2.3 meter and above.
GROUND

52"
吊 扇
安装手册
安全注意事项和安装程序
RCF-Mercury-5BL
RCF-Mercury-5BL

11
9
2
3
4
5
6
8
1
712
7A
10
13
配 件 明 细
拆箱后,请逐一清点以下零件
零件 数量 配件包 数量
1. 吊盅
2. 吊杆
3. 接头盖
4. 风扇主体
5. 玻璃灯罩
6. 叶片
7. 遥控器附1粒12伏电池
7A. 壁座附2个螺丝
8. 接收器
1
1
1
1
1
5
1
1
1
9. 叶片螺丝包
10. 纸垫片
11. 接线帽
12. 安全挂钩
13. 平衡包
16
16
6
1
1
元 件 配 件 包
这些测试数据不包括灯使用的功率
1
尺寸 电压/频率 最大功率 最大转速 净重 毛重
52"11.8kgs 13.0kgs
250+-10%
80W
240V/50Hz