Russell Hobbs RHDF 30 Installation instructions manual

INSTRUCTIONS/WARRANTY
MODEL: RHDF 30 – 30CM DESK FAN
INTRODUCTION
Thank you for purchasing the Russell Hobbs RHDF-30 Oscillating Desk fan. Each
unit has been manufactured to ensure safety, reliability & ease of use. Before use,
please read these instructions carefully, and keep them for further reference.
IMPORTANT SAFEGUARDS
When using your Russell Hobbs fan, basic precautions should always be followed
including the following:
•Make sure the power used corresponds to the one indicated on the rating
label.
•Use the fan only for use as described in this instruction manual.
•To protect against electrical shock, do not place fan in front of a window.
•Do not cover.
•Do not immerse unit, plug or cord in water or allow for liquid to come into
contact with any part of the fan.
•Close supervision is necessary when any appliance is used by or near
children.
•Unplug the fan from the power supply when: not in use, when moving from
one location to another, before putting on or taking off parts and before
cleaning.
•Avoid coming into contact with any moving part.
•To avoid vibration, place the fan on a smooth level surface.
•Never operate the fan with a damaged power cord or plug, or after it has
fallen or damaged in any way.
•Do not allow objects to fall into the openings and do not insert objects
through the guard when the fan is in operation.
•Do not operate without fan grilles properly in place.
•Do not use outdoors.
1
All manuals and user guides at all-guides.com
all-guides.com

•Do not let cord hang over edge of table or counter, or touch hot surfaces.
•To disconnect, grip plug, and pull from wall outlet. Never pull on the cord.
•Do not try to cover, extend or stretch the mains cable.
•Never attempt to open any part or dismantle the controls. Responsibility for
failure cannot be accepted if this instruction has been ignored.
•This product is intended for household use only. Industrial or commercial
use invalidates the warranty.
PARTS NAME AND LOCATION
ASSEMBLY INSTRUCTIONS
Your Russell Hobbs Fan has been boxed unassembled to minimize packaging
waste. Each part fits together easily and can be removed for cleaning, and storage.
1. Take the fan out of the box and remove any protective wrappings.
2. Place all the parts on the floor.
3. Remove the three position screws on the base, align the base with the
three holes on the holding plate, insert the three position screws and
tighten.
4. Remove the four position screws on the motor and align the rear guard
with the four holes on the motor (handle facing top of the fan) insert the
four Position screws and tighten.
5. Loosen the set screw on the blade, slide the blade on to the shaft of the
motor.Tighten the set screw on to the flat side of the shaft to secure the
blade ensuring the blade does not damage the guards.
6. Assemble the front guard to the rear guard. Tighten the connecting screw
and nut; thereafter secure the retaining clips..
THERMAL CUT-OUT DEVICE
The motor has a thermal cut-out device. Whenever the fan overheats, due to
various reasons, the temperature of the motor reaches fusing point and the fan will
cut off automatically which will make the fan safe.
2
3
All manuals and user guides at all-guides.com

OPERATING INSTRUCTIONS
1. The on/off switch is incorporated in the speed control switch on the head of
the fan.
2. Your Russell Hobbs fan control has three speed settings. The various
speed settings assist in regulating the airflow from the fan.
a) Pull once for low speed and air circulation
b) Pull twice for medium speed and air circulation
c) Pull three times for high speed and air circulation
3. The fan can operate in oscillation or static mode;
4. To make the fan head oscillate, push down the Oscillation Knob.
5. To stop the fan head from oscillating pull the Oscillation Knob up.
6. The head of the fan can be adjusted up or down - to do this loosen the
adjusting knob, adjust the fan to the desired angle. To secure tighten the
Adjusting Knob.
CLEANING
1. Before cleaning, always ensure the fan is switched off and disconnected
from the electrical socket.
2. Wipe off dust and dirt with a warm moist cloth and then buff with dry cloth.
3. Do not immerse the fan in water or other fluids.
PROBLEM SOLVING
There are no user serviceable parts in this appliance. If the appliance is not
operating correctly, please check that:
1 You have followed the instructions correctly.
2.The unit has been wired correctly and the wall socket is switched on
3. The mains power supply is ON.
If the appliance still does not work:
In the first instance, consult your retailer for possible repair or replacement. If your
retailer fails to solve your problem and you need to return the appliance, make sure
that:
1. The unit is packed carefully and complete into its original packaging.
2. Proof of purchase is attached.
3. Give the reason why you are returning it.
If the supply cord is damaged, it must be replaced by the manufacturer or its
Service Agents in order to avoid a hazard. If service should become necessary
within the warranty period, the appliance should be returned to an approved
Amalgamated Appliances Pty Ltd service center. Servicing outside the warranty
period is still available, however this will be chargeable. If the power supplies cord
becomes damaged the manufacturer or an approved service agent must replace it.
PLEASE AFFIX YOUR PROOF OF PURCHASE/RECEIPT HERE
IN THE EVENT OF A CLAIM UNDER WARRANTY THIS RECEIPT MUST BE
PRODUCED.
5
All manuals and user guides at all-guides.com

PLEASE AFFIX YOUR PROOF OF PURCHASE/RECEIPT HERE
IN THE EVENT OF A CLAIM UNDER WARRANTY THIS RECEIPT MUST BE PRODUCED.
W A R R A N T Y
1. Tedelex Trading (Pty) Limited (“Tedelex”) warrants to the original purchaser of this
product (“the customer”) that this product will be free of defects in quality and
workmanship which under normal personal, family or household use and purpose
may manifest within a period of 1 (one) year from the date of purchase (“warranty
period”).
2. Where the customer has purchased a product and it breaks, is defective or does not
work properly for the intended purpose, the customer must notify the supplier from
whom the customer bought the product (“the supplier”) thereof within the warranty
period. Any claim in terms of this warranty must be supported by a proof of purchase.
If proof of purchase is not available, then repair, and/or service charges may be
payable by the customer to the supplier.
3. The faulty product must be taken to the supplier's service centre to exercise the
warranty.
4. The supplier will refund, repair or exchange the product in terms of this warranty
subject to legislative requirements. This warranty shall be valid only where the
customer has not broken the product himself, or used the product for something that it
is not supposed to be used for. The warranty does not include and will not be
construed to cover products damaged as a result of disaster, misuse, tamper, abuse
or any unauthorised modification or repair of the product.
5. This warranty will extend only to the product provided at the date of the purchase and
not to any expendables attached or installed by the customer.
6. If the customer requests that the supplier repairs the product and the product breaks
or fails to work properly within 3 (three) months of the repair and not as a result of
misuse, tampering or modification by or on behalf of the customer, then the supplier
may replace the product or pay a refund to the customer.
7. The customer may be responsible for certain costs where products returned are not in
the original packaging, or if the packaging is damaged. This will be deducted from any
refund paid to the customer.
TEDELEX TRADING (PTY) LTD (JOHANNESBURG)
JOHANNESBURG TEL NO. [phone]
CAPE TOWN TEL NO. [phone]
DURBAN TEL NO. [phone]
www.amap.co.za
All manuals and user guides at all-guides.com

All manuals and user guides at all-guides.com