Russell Hobbs 20240AU Installation instructions manual

20240AU_IB&RB_FA_291113
2 YEAR WARRANTY
MULTI PROCESSOR
20240AU
INSTRUCTIONS & WARRANTY

Spectrum Brands Australia Pty Ltd
Locked Bag 3004 Braeside
Victoria 3195 Australia
Customer Service in Australia
Toll Free: 1800 623 118
Email: [email protected]
Website: www.spectrumbrands.com.au
Spectrum Brands New Zealand Ltd
PO Box 9817 Newmarket
Auckland 1149 New Zealand
Customer Service in New Zealand
Toll Free: 0800 736 776
Email: ser[email protected].nz
Website: www.spectrumbrands.co.nz
W
0911
Spectrum Brands Australia Pty Ltd and Spectrum Brands New Zealand Ltd
Warranty Against Defects
In this warranty:
Australian Consumer Law means the Australian consumer law set out in Schedule 2 to the Competition
and Consumer Act 2010;
CGA means the New Zealand Consumer Guarantees Act 1993;
Goods means the product or equipment which was accompanied by this warranty and purchased in
Australia or New Zealand, as the case may be;
Manufacturer, We or us means:
1. for Goods purchased in Australia, Spectrum Brands Australia Pty Ltd ABN, 78 007 070 573;
or
2. for Goods purchased in New Zealand, Spectrum Brands New Zealand Ltd, as the case may be,
contact details as set out at the end of this warranty;
Supplier means the authorised distributor or retailer of the Goods that sold you the Goods in Australia or
in New Zealand; and
You means you, the original end-user purchaser of the Goods.
1. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law, or
the CGA. You are entitled to a replacement or refund for a major failure and compensation for any
other reasonably foreseeable loss or damage. You are also entitled
to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
2. The benets provided by this Warranty are in addition to all other rights and remedies in respect of
the Goods which the consumer has under either the Australian Consumer Law
or the CGA. The original purchaser of the Goods is provided with the following Warranty subject to
the Warranty Conditions:
3. We warrant the Goods for all parts defective in workmanship or materials from the date
of purchase (Warranty Period), for the period of:-
(a) Two (2) years for Russell Hobbs products (see product packaging for details)
(b) Two (2) years with ve (5) year motor warranty for Russell Hobbs products (see product
packaging for details)
(c) Limited Lifetime, Ten (10) years for Russell Hobbs cookware.
(d) One (1) year for George Foreman.
If the Goods prove defective within the Warranty Period by reason of improper workmanship
or material, we may, at our own discretion, repair or replace the Goods without charge.
Warranty Conditions
4. The Goods must be used in accordance with the manufacturer’s instructions. This Warranty
does not apply should the defect in or failure of the Goods be attributable
to misuse, abuse, accident or non-observance of manufacturer’s instructions on the part of
the user. As far as the law permits, the manufacturer does not accept liability for any direct or
consequential loss, damage or other expense caused by or arising out of any failure to use
the Goods in accordance with the manufacturer’s instructions.
5. Exhaustible components (such as batteries, lters and brushes) of the Goods are included
under this Warranty only where there is a defect in workmanship or materials used.
6. The warranty granted under clause 3 is limited to repair or replacement only.
7. Any parts of the Goods replaced during repairs or any product replaced remain the property
of the manufacturer. In the event of the Goods being replaced during the Warranty Period,
the warranty on the replacement Goods will expire on the same
date as for the Warranty Period on the original Goods which are replaced.
8. In order to claim under the warranty granted under clause 3 you must:
(a) Retain this warranty with your receipt/proof of purchase; and
(b) Return the Goods to us at the relevant address or to the Supplier by prepaid freight
within the Warranty Period accompanied with (i) the legible and unmodied original
proof of purchase, which clearly indicates the name and address of the Supplier, the date
and place of purchase, the product name or other product serial number and (ii) this
warranty.
9. This warranty is immediately void if:
(a) Any serial number or appliance plate is removed or defaced;
(b) The Goods have been serviced or otherwise repaired by a person not authorised to do so
by us or where non approved replaced parts are used.
10. The Goods are designed for domestic use only. A limited 90-day Warranty applies to any
industrial or commercial use of the Goods. The Goods must be connected to the electrical
voltage requirements as specied in the ratings label located on the Goods.
11. This warranty does not cover the cost of claiming under the warranty or transport
of the Goods to and from the Supplier or us.
12. This warranty is only valid and enforceable in Australia against Spectrum Brands Australia Pty
Ltd and in New Zealand against Spectrum Brands New Zealand Ltd.
Contact us or the Supplier for further details.
Register your product online
If you live in Australia please visit: www.spectrumbrands.com.au/warranty
If you live in New Zealand Please visit: www.spectrumbrands.co.nz/warranty
Registration of your warranty is not compulsory, it gives us a record of your purchase
AND entitles you to receive these benets: Product information; Hints and tips; Recipes and
news; Information on special price oers and promotions.
Any questions? Please contact Customer Service for advice.
2

Spectrum Brands Australia Pty Ltd
Locked Bag 3004 Braeside
Victoria 3195 Australia
Customer Service in Australia
Toll Free: 1800 623 118
Email: [e-mail]
Website: www.spectrumbrands.com.au
Spectrum Brands New Zealand Ltd
PO Box 9817 Newmarket
Auckland 1149 New Zealand
Customer Service in New Zealand
Toll Free: 0800 736 776
Email: [e-mail]
Website: www.spectrumbrands.co.nz
W
0911
Spectrum Brands Australia Pty Ltd and Spectrum Brands New Zealand Ltd
Warranty Against Defects
In this warranty:
Australian Consumer Law means the Australian consumer law set out in Schedule 2 to the Competition
and Consumer Act 2010;
CGA means the New Zealand Consumer Guarantees Act 1993;
Goods means the product or equipment which was accompanied by this warranty and purchased in
Australia or New Zealand, as the case may be;
Manufacturer, We or us means:
1. for Goods purchased in Australia, Spectrum Brands Australia Pty Ltd ABN, 78 007 070 573;
or
2. for Goods purchased in New Zealand, Spectrum Brands New Zealand Ltd, as the case may be,
contact details as set out at the end of this warranty;
Supplier means the authorised distributor or retailer of the Goods that sold you the Goods in Australia or
in New Zealand; and
You means you, the original end-user purchaser of the Goods.
1. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law, or
the CGA. You are entitled to a replacement or refund for a major failure and compensation for any
other reasonably foreseeable loss or damage. You are also entitled
to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
2. The benets provided by this Warranty are in addition to all other rights and remedies in respect of
the Goods which the consumer has under either the Australian Consumer Law
or the CGA. The original purchaser of the Goods is provided with the following Warranty subject to
the Warranty Conditions:
3. We warrant the Goods for all parts defective in workmanship or materials from the date
of purchase (Warranty Period), for the period of:-
(a) Two (2) years for Russell Hobbs products (see product packaging for details)
(b) Two (2) years with ve (5) year motor warranty for Russell Hobbs products (see product
packaging for details)
(c) Limited Lifetime, Ten (10) years for Russell Hobbs cookware.
(d) One (1) year for George Foreman.
If the Goods prove defective within the Warranty Period by reason of improper workmanship
or material, we may, at our own discretion, repair or replace the Goods without charge.
Warranty Conditions
4. The Goods must be used in accordance with the manufacturer’s instructions. This Warranty
does not apply should the defect in or failure of the Goods be attributable
to misuse, abuse, accident or non-observance of manufacturer’s instructions on the part of
the user. As far as the law permits, the manufacturer does not accept liability for any direct or
consequential loss, damage or other expense caused by or arising out of any failure to use
the Goods in accordance with the manufacturer’s instructions.
5. Exhaustible components (such as batteries, lters and brushes) of the Goods are included
under this Warranty only where there is a defect in workmanship or materials used.
6. The warranty granted under clause 3 is limited to repair or replacement only.
7. Any parts of the Goods replaced during repairs or any product replaced remain the property
of the manufacturer. In the event of the Goods being replaced during the Warranty Period,
the warranty on the replacement Goods will expire on the same
date as for the Warranty Period on the original Goods which are replaced.
8. In order to claim under the warranty granted under clause 3 you must:
(a) Retain this warranty with your receipt/proof of purchase; and
(b) Return the Goods to us at the relevant address or to the Supplier by prepaid freight
within the Warranty Period accompanied with (i) the legible and unmodied original
proof of purchase, which clearly indicates the name and address of the Supplier, the date
and place of purchase, the product name or other product serial number and (ii) this
warranty.
9. This warranty is immediately void if:
(a) Any serial number or appliance plate is removed or defaced;
(b) The Goods have been serviced or otherwise repaired by a person not authorised to do so
by us or where non approved replaced parts are used.
10. The Goods are designed for domestic use only. A limited 90-day Warranty applies to any
industrial or commercial use of the Goods. The Goods must be connected to the electrical
voltage requirements as specied in the ratings label located on the Goods.
11. This warranty does not cover the cost of claiming under the warranty or transport
of the Goods to and from the Supplier or us.
12. This warranty is only valid and enforceable in Australia against Spectrum Brands Australia Pty
Ltd and in New Zealand against Spectrum Brands New Zealand Ltd.
Contact us or the Supplier for further details.
Register your product online
If you live in Australia please visit: www.spectrumbrands.com.au/warranty
If you live in New Zealand Please visit: www.spectrumbrands.co.nz/warranty
Registration of your warranty is not compulsory, it gives us a record of your purchase
AND entitles you to receive these benets: Product information; Hints and tips; Recipes and
news; Information on special price oers and promotions.
Any questions? Please contact Customer Service for advice.
3

4
Congratulations on the purchase of your new Russell Hobbs appliance. Each unit is
manufactured to ensure safety and reliability.
Before using the appliance for the first time, please read this instruction booklet carefully
and keep it for future reference. Pass it on if you pass on the appliance.
When using this appliance, basic safety precautions should always be followed.
Dishwasher safe
1. Speed control
2. Motor unit
3. Light ring
4. Black spindle
5. Processor bowl
6. Processor bowl handle
7. White centre post
8. Chopping blade
9. Dough blade
10. Creamer
11. Processor bowl lid
12. Food chute
13. Food pusher
14. Fine grating disc
15. Reversible slicing/
coarse grating disc
16. Blender lid cap
17. Blender lid
18. Blender handle
19. Blender jug
2
31
6
12
13
P
O
MAX
max
4
7
14
15
11
8 9 10
519
4
16
17
18

5
BEFORE FIRST USE
• Carefully remove all contents from the box.
• Take extreme care when unpacking and handling the sharp blades.
• As some parts may be packed separately, check to ensure all items have been unpacked
before disposing of the packaging.
• Dismantle and clean all parts as instructed in the "CARE AND CLEANING" section of this
manual.
THE LIGHT RING
Your Colour Control Multi Processor has been designed with the optimal number of speeds and
has been created to simplify use - each speed corresponds to a specic type of use.
This is displayed in a unique way with a “light ring” that illuminates and changes colour
according to the speed.
The light will change colour as the speed changes:
SPEED COLOUR USE
O ~ Off
1 Blue Slicing/ shredding/ grating
2 Purple Dough/ cakes/ cream
3 Green Blending/ other
P Red Chopping/ smaller batches
Turning the speed control anti-clockwise to P will give you a short burst at high speed, for more
precise control. In this direction, the control is spring-loaded. When you let go, it will return to O.
NOTE: See section Speed Selection Guide on page 13 for more information on what
speed to uses for different tasks.
IMPORTANT ASSEMBLY INFORMATION
Due to the safety interlock features present in this food processor, the following parts must be
in position in order for the food processor to operate:
THE PROCESSOR BOWL MUST BE LOCKED INTO POSITION ON THE MOTOR UNIT
1. Fit the black spindle to the top of the motor unit so the notches are aligned.
2. Lower the processor bowl over the black spindle with the handle on the right, aligning 
on the bottom of the processor bowl with on rim of the motor unit.
3. Ensure the processor bowl is seated correctly, hold the handle and rotate clockwise to
alignon the processor bowl with on the motor unit until it clicks rmly into place.
4. This must be correctly completed before moving to the next step.

6
THE PROCESSOR BOWL LID MUST BE LOCKED INTO POSITION ON THE PROCESSOR BOWL
1. Place the processor bowl lid over the processor bowl with the feed chute on the right,
aligningon the processor bowl lid with on the processor bowl.
2. Hold the food chute and rotate clockwise to alignon the processor bowl lid with on the
processor bowl until it clicks rmly into place.
3. This must be correctly in place before trying to operate the food processor.
IMPORTANT:
For your protection this appliance has an interlock system. The processor will not
operate unless the processor bowl and lid are properly aligned and locked into place.
Do not try to move the lid or the processor bowl while the motor is running.
The processor bowl cannot be removed from the motor unit when the lid is locked in
place. Remove the lid, then remove the processor bowl.
The processor bowl cannot be locked onto the motor unit when the lid is locked in place.
Remove the lid, then lock the processor bowl onto the motor unit.
OPERATING THE MULTI PROCESSOR
CAUTION: Always turn off and unplug from the wall power outlet before fitting or
removing attachments.
IMPORTANT: Do not run the motor for longer than 1 minute. After 1 minute, switch off for
at least 2 minutes to allow the motor to cool down.
HOW TO CHOP IN THE PROCESSOR BOWL
The chopping blades are used to process, chop, mince, mix and puree foods to a smooth
consistency.
CAUTION: DO NOT handle by the blade. The blade attachments are very sharp. Use
caution when handling and storing.
1. Ensure the black spindle is in position.
2. Lock the processor bowl onto the motor unit. (see page 5).
3. Lower the white centre post into the centre of the processor bowl, over the black spindle.
4. Hold the chopping blade by the plastic centre and insert it onto the white centre post and
slide it to the bottom of the bowl.
NOTE: The chopping blade will only fit correctly onto the white centre post one way.
5. Place food in the processor bowl.
NOTE: When processing only liquids, do not fill the processor bowl past max .
NOTE: When processing solids, or a combination of liquids and solids, do not fill past MAX.
6. Place the lid on the processor bowl and lock into place. (see page 6).

7
7. Place the food pusher in the food chute.
CAUTION: Never use your fingers to direct food through chute.
8. Switch the motor unit on to the desired speed or pulse setting using the speed control.
Refer to the Speed Selection Guide on page 13 for ideal speed settings to match your
processing task.
TIP: Process foods no more than a few seconds at a time. Pulsing produces excellent
results and offers greater control.
9. To add food or liquid while the processor is running, remove the food pusher and insert
food or liquid through the food chute. Replace food pusher in the chute.
10. When nished, turn the speed control to the ‘O’ off position and wait until the chopping
blade stops moving.
IMPORTANT: Be sure the chopping blade has completely stopped spinning before
removing lid from processor.
11. Switch the power off and remove the plug from the wall power outlet.
12. To remove the lid hold the food chute and rotate to alignon the processor bowl lid with
on the processor bowl.
13. To remove the processor bowl, hold the handle and rotate to alignon the processor bowl
with on the motor unit and lift off the motor unit.
NOTE: Remove the processor bowl from the motor unit before removing the chopping
blade to prevent food from leaking through the centre opening of the processor bowl.
14. Carefully remove the chopping blade and empty processor bowl.
HELPFUL TIPS FOR CHOPPING AND BLENDING
• The processor works very quickly so please watch carefully to avoid over-processing
foods.
• The PULSE function offers the best control and results.
• For best results, try to process foods that are cut to be about the same size.
• Do not overload the bowl.
• Never walk away from the processor while it is on.
• Never put boiling liquids into the food processor, always let them cool for at least 10
minutes before processing. Ingredients should be below 40°C.
• When processing only liquids, do not ll the jug past max .
• When processing solids, or a combination of liquids and solids, do not ll past MAX.

8
SLICING OR GRATING IN THE PROCESSOR BOWL
Use the discs to slice and grate ingredients such as vegetables, fruit and cheese.
CAUTION: The slicing and grating discs are very sharp. Use caution when handling and storing.
1. Ensure the black spindle is in position.
NOTE: The white centre post must not be in place in order for the disc to fit into the
processor bowl to function.
2. Lock the processor bowl into position. (see page 5).
3. Carefully place the desired disc on the black spindle. Place disc with grating or slicing
blade just to the left of the food chute to allow the disc one full rotation before coming in
contact with the food.
• For fine grating, fit the fine grater, with the rough side on top.
• For slicing, the slicing blade must be on top of the disc.
• For coarse grating, the slicing blade must be on the bottom of the disc.
CAUTION: The disc attachments are very sharp. Use caution when handling and storing.
4. Place the lid on the processor bowl and lock into place (see page 5).
5. Add food into the food chute and place the food pusher on top to use as a guide.
6. Switch the motor unit on the desired speed setting using the speed control. Refer to the
Speed Selection Guide on page 13 for ideal speed settings to match your processing task.
7. Press lightly but rmly on the large or small food pusher to guide food through the
processor.
CAUTION: Never use your fingers to direct food through chute.
NOTE: Heavy pressure on the food pusher does not speed up the work; use the food
pusher only as a guide. Let the processor do the work.
NOTE : Do not let the processor bowl overload – stop and empty it when it gets half full.
8. When nished, turn the speed control to the ‘O’ off position and wait until the disc stops
moving.
IMPORTANT: Be sure the disc has completely stopped spinning before removing lid from
processor.
9. Switch the power off and remove the plug from the wall power outlet.
10. To remove the lid hold the food chute and rotate to alignon the processor bowl lid with
on the processor bowl.
11. Carefully remove the disc from the black spindle.
12. To remove the processor bowl, hold the handle and rotate to alignon the processor bowl
with on the motor unit and lift off the motor unit.
NOTE: Remove the processor bowl from the motor unit before removing the disc to
prevent food from leaking through the centre opening of the processor bowl.
13. Empty the processor bowl.

9
HELPFUL TIPS WHEN SLICING AND GRATING
• Before slicing round fruits and vegetables through the processor cut a thin slice from the
bottom so food will be more stable. Place food cut side down in food chute.
• Always remove seeds, core and pits before processing.
• Select foods that are rm and not over ripe.
• Remove the core from hard vegetables, such as cabbage.
• When slicing thinner vegetables stand them vertically in the food chute so they are solidly
packed and cannot turn or tilt.
• Grate hard cheeses at room temperature.
• Soft and semi hard cheeses should be well chilled before grating.
USING THE DOUGH BLADE
This blade makes preparing dough efcient and time saving.
1. Ensure the black spindle is in position.
2. Lock the processor bowl onto the motor unit. (see page 5).
3. Lower the white centre post into the centre of the processor bowl, over the black spindle.
4. Insert the dough blade onto the white centre post and slide it to the bottom of the bowl.
5. Insert all the dry ingredients into the processor bowl and pulse to combine.
6. Place the lid on the processor bowl and lock into place (see page 6).
7. Ensure the food pusher is in place and process using speed setting 2 (purple).
NOTE: Refer to the Speed Selection Guide on page 13 for ideal speed settings to match
your processing task.
8. With the processor running, add liquids through the food chute if required.
9. When nished, turn the speed control to the ‘O’ off position and wait until the dough blade
stop moving.
IMPORTANT: Be sure the dough blade has completely stopped spinning before removing
lid from processor.
10. Switch the power off and remove the plug from the wall power outlet.
11. To remove the lid hold the food chute and rotate to alignon the processor bowl lid with
on the processor bowl.
12. To remove the processor bowl, hold the handle and rotate to alignon the processor bowl
with on the motor unit and lift off the motor unit.
NOTE: Remove the processor bowl from the motor unit before removing the dough blade
to prevent food from leaking through the centre opening of the processor bowl.
13. Carefully remove the dough blade and empty the processor bowl.

10
HELPFUL TIPS WHEN USING THE DOUGH BLADE
• For best results do not prepare recipes using more than 3 cups our or less than 1 cup.
• Pour liquid through food chute in a slow steady stream.
• Process dough in the processor no longer than 1 minute.
• Do not leave processor unattended during operation.
• This blade does not extend to the outside rim of the processor bowl so it cannot
incorporate our when very small amounts of our are being processed.
USING THE CREAMER
Use the creamer to thicken cream, to beat eggs, and to cream softened butter and sugar
together.
1. Ensure the black spindle is in position.
2. Lock the processor bowl onto the motor unit. (see page 5).
3. Lower the white centre post into the centre of the processor bowl, over the black spindle.
4. Insert the creamer onto the white centre post and slide it to the bottom of the bowl.
5. Place ingredients into the processor bowl.
6. Place the lid on the processor bowl and lock into place (see page 6).
7. Ensure the food pusher is in place and process using speed setting 2 (purple).
NOTE: Refer to the Speed Selection Guide on page 13 for ideal speed settings to match
your processing task.
8. With the processor running, add liquids through the food chute if required.
9. When nished, turn the speed control to the ‘O’ off position and wait until the creamer
stops moving.
IMPORTANT: Be sure the creamer has completely stopped spinning before removing lid
from processor.
10. Switch the power off and remove the plug from the wall power outlet.
11. To remove the lid hold the food chute and rotate to alignon the processor bowl lid with
on the processor bowl.
12. To remove the processor bowl, hold the handle and rotate to alignon the processor bowl
with on the motor unit and lift off the motor unit.
NOTE: Remove the processor bowl from the motor unit before removing the creamer to
prevent food from leaking through the centre opening of the processor bowl.
13. Carefully remove the creamer and empty the processor bowl.

11
USING THE BLENDER JUG
LOCKING THE BLENDER JUG IN POSITION
1. Lower the blender jug onto the motor unit with the handle on the right. Alignon the
bottom of the blender jug with on the motor unit.
2. Ensure the blender jug is seated correctly, hold the handle and rotate clockwise to
alignon the blender jug with on the motor unit until it clicks rmly into place.
3. Place the ingredients you wish to blend into the blender jug.
IMPORTANT: Do not fill it past the 1250ml mark. If you do, the contents may force the lid
off when starting the motor.
4. Fit the lid onto the jug, press down rmly.
5. Insert the lid cap into the opening of the lid by aligning the cap tabs with the notches in the
lid opening. Turn it in a clockwise direction to lock it in place.
NOTE: Do not run the blender without the lid cap, as ingredients may be ejected through
the hole.
6. Place your hand on top of the blender jug lid to hold the jug steady. Switch the motor
unit on to the desired speed or pulse setting using the speed control. Refer to the Speed
Selection Guide on page 13 for ideal speed settings to match your blending task.
NOTE: To use the pulse setting the speed control must be held in the ‘P’ position for the
motor to run. When the switch is released, the motor will stop.
7. When nished, turn the speed control to the ‘O’ off position and wait until the blades stop
moving.
IMPORTANT: Be sure the blades have completely stopped spinning before removing the
lid from blender jug.
8. Switch the power off and remove the plug from the wall power outlet.
IMPORTANT:
• The Lid MUST ALWAYS be in place before starting the blender.
• Do not run the motor for longer than 1 minute. After 1 minute, switch off for at least
2 minutes to allow the motor to cool down.
• When blending cooked ingredients always let them cool for at least 10 minutes
before blending. Liquids and ingredients should be below 40°C.
GENERAL TIPS FOR USING THE PROCESSOR
• Organise processing tasks to avoid multiple cleanups of the bowl; process dry before wet.
• To take advantage of the speed of the processor, drop foods through the food chute with
the processor running.
• Apply light pressure on the food pusher for soft foods (berries and tomatoes) and slightly
more pressure for hard foods (onions and potatoes).
• Do not process foods that are so frozen or hard that the tip of a knife cannot be inserted
into the food.
• When chopping sticky dried fruits, place the fruits in the freezer for about 10 minutes and
add a little our to keep the pieces from sticking together.

12
• Chill soft cheeses before slicing and grating to prevent the cheese from rolling into a ball
on the disc.
• When using the slicing / grating disc do not let the food accumulate too high; stop and
empty the processor bowl.
• Do not use the processor to:
• Process bones, grains or hard spices
• Process meat
• Liquify fruits and vegetables
• Slice or chop warm hard boiled eggs, chill them rst

13
SPEED SELECTOR GUIDE
GENERAL FOOD ITEMS
ATTACHMENT
SPEED SETTING COLOUR
CONTROL
CHOPPING
BLADE
DOUGH
BLADE CREAMER FINE
GRATER SLICER COARSE
GRATER
BLENDER
JUG
Biscuits crumb üPULSE RED
Breadcrumbs üPULSE RED
Bread Dough, Pizza
Dough, Scone Dough ü2 PURPLE
Butter and Sugar ü ü 2 (PULSE FIRST) RED / PURPLE
Cake mix & batter ü2 (PULSE FIRST) RED / PURPLE
Chocolate, pieces ü ü PULSE RED
Cocktails ü ü 3 (PULSE FIRST) RED / GREEN
Coffee beans üPULSE RED
Cream, whipping ü2 PURPLE
Curry pastes ü ü 3 GREEN
Dips, chunky including pesto ü ü PULSE RED
Dips, smooth ü ü 3 GREEN
Dressing and Sauces ü ü 3 GREEN
Dried herbs üPULSE RED
Egg whites ü2 PURPLE
Fruit raw eg. Banana,
pineapple, rhubarb,
peaches
ü ü 1 BLUE
Fruit raw eg. Mangoes,
prunes (pitted) ü1 BLUE
Fruit smoothies ü ü 3 GREEN
Fruit, cooked ü ü 3 GREEN
Fruit, raw eg. Apples ü ü ü 1 BLUE
Hard Cheese eg.
Parmesan, Romano ü ü 1 BLUE
Marinades ü ü 3 GREEN
Mayonnaise ü ü 3 GREEN
Milkshakes ü ü 3 GREEN
Minced meat for
hamburgers & rissoles üPULSE RED
Nuts, eg. walnuts,
almonds, pinenuts and
other soft nuts
ü ü PULSE RED
Pancake batter ü ü 2 PURPLE
Purees ü ü 3 GREEN
Seeds üPULSE RED
Smoothies ü ü 3 GREEN
Soup, chunky ü ü PULSE RED
Soup, smooth ü ü 3 GREEN
Thickshakes ü ü 3 GREEN
Vegetables, cooked ü ü 1 BLUE
Vegetables, raw eg.
Leek, fennel, cucumber ü ü ü 1 BLUE
Vegetables, raw eg.
Potatoes, cabbage,
carrots, beetroot
ü ü ü 1 BLUE

14
TROUBLE SHOOTING
PROBLEM POSSIBLE CAUSE SOLUTION
Food is unevenly chopped. Processor bowl is overfilled.
You may be running the bowl
continuously instead of using
Pulse.
Food may be cut in random sizes.
Smaller amounts will process more
evenly.
Use the Pulse button in 5 second
intervals or less. Allow the blades to stop
completely before pressing the PULSE
button again.
Cut food into 2cm pieces before placing
in processor.
Liquid leaks from the bottom of
the processor bowl.
Too much liquid in the processor
bowl.
Process smaller amounts.
When processing only liquids, do not fill
the processor bowl past max
Do not remove the blade before
removing processor bowl from the motor
unit when processing liquids.
Sliced foods are uneven and
slanted.
The feed chute has not been well
packed or uneven pressure has
been applied to the food pusher
during processing.
Cut pieces in even lengths, just a little
shorter than the length of the feed chute.
Pack the chute carefully and maintain
even pressure on the food pusher as the
food is being processed.
Foods being sliced or grated fill
up on one side of the bowl.
This is normal. Stop processing occasionally and either
even out the food in the processor bowl
or move it to another bowl.
When food accumulates close to the
disc, empty the processor bowl before
continuing.
Some pieces of food remain on
top of the slicing and grating
disc.
This is normal. Slice or grate those pieces by hand or
save for another use, eg. soups that will
be pureed.
Soft cheese collects on top of
the slicing and grating disc.
The cheese was not cold enough.
The pressure exerted on the
pusher was too great.
Be sure soft cheeses are well chilled or
place in freezer until knife inserted into
cheese penetrates about 12mm.
Remember food pusher is to be used as
a guide; never exert hard pressure on the
food pusher.

15
CARE AND CLEANING
IMPORTANT: Before cleaning, be sure unit is turned off and cord is unplugged. Care
should be taken when handling sharp cutting blades and discs when emptying the bowl
and during cleaning.
CLEANING
• Completely empty and disassemble processor parts before washing.
• Rinse parts immediately after processing/blending for easy cleaning.
• To easily clean the processor bowl or blender jug, once empty add a drop of detergent and
a little warm water and pulse several times. Rinse and wipe clean before re-using.
NOTE: Do not fill the jug past max .
• Wipe motor unit and feet with a damp cloth and dry thoroughly.
• Stubborn spots can be removed by gentle rubbing with a damp cloth and a mild, non-
abrasive cleaner.
• Do not immerse motor unit in liquid.
• Dishwasher safe parts are labelled on page 4 with a symbol. All parts except for the
motor unit and blender jug are dishwasher safe.
• All removable parts can be washed by hand or in a dishwasher. Hand-washing of plastic
parts will help to maintain the food processor’s appearance.
• If washing in a dishwasher, place removable parts on the top rack only.
• Do not use alkaline cleaning agents or harsh abrasives when cleaning this appliance.
• If washing by hand, wash with warm to hot soapy water and use a soft cloth.
• Ensure all stubborn food remains are rinsed out of hard to reach areas before drying and
storing.
• Do not use rough scouring pads or cleansers on any plastic or metal parts.
• Do not allow blades or discs to soak in water for long periods of time.
• Rinse well and allow all parts to dry before storing.
CAUTION: Do not attempt to sharpen the cutting edges of the blades or discs. They are
permanently sharpened at the factory and will be ruined by attempted sharpening.

16
IMPORTANT SAFEGUARDS
When using this appliance, basic safety precautions should always be followed, including the
following:
1. To protect against electric shock do not immerse cord, plug or motor unit in water or liquid.
2. Do not use outdoors or in damp or moist areas.
3. This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
4. Always switch off and disconnect the appliance from the wall power outlet before
assembling, disassembling or cleaning.
5. Always switch off and disconnect the appliance from the wall power outlet when not in use.
6. To disconnect, set the appliance controls to off ‘O’. Switch off the wall power outlet, then
grasp the plug and pull the plug from wall outlet. Never pull by the cord.
7. Do not operate any appliance with a damaged cord or plug or after the appliance has
malfunctioned, or has been dropped or damaged in any manner. Contact customer service
for replacement, examination, repair or adjustment.
8. There are no user serviceable parts. If the power cord is damaged, it must be replaced by
the manufacturer or a suitably qualied person in order to avoid a hazard.
9. Do not use this appliance for other than its intended use. Using this appliance for other
than its intended purpose may result in personal injury.
10. Use only the accessories supplied with this appliance. The use of accessory attachments
not recommended by the appliance manufacturer may cause injuries.
11. Do not use on an inclined plane or unstable surface.
12. Keep the appliance and power cord away from the edge of tables or countertops and out
of reach of children and persons with disabilities.
13. Do not place on or near any heat surfaces.
14. The motor will only operate once the processing bowl, lid and large food pusher have been
securely tted onto the motor unit.
15. Do not operated the blender with an empty jug.
16. For your safety, do not blend liquids/foods that are hotter than 40°C. Allow boiling liquids
to cool before you pour them into the blender jug or food processor bowl.
17. Keep hands and utensils away from moving blades or discs while processing foods to
prevent the possibility of severe personal injury or damage to the Multi Processor. A
scraper may be used, but it must be used only when the food processor is not running.
18. Wait until the blades come to a complete stop before removing the lid from the jug, and
before removing the jug from the motor unit.
19. Cutting blades are very sharp. Care must be taken when handling the sharp cutting blades,
when emptying the bowl and during cleaning.
20. This appliance must be monitored when in use. Do not leave the appliance unattended
when switched on.
21. To reduce the risk of injury, never place chopping blade or disc on the motor unit without
rst tting the bowl securely in place.
22. Be certain the lid is securely locked in place before operating appliance.

17
23. Do not run the motor for longer than 1 minute. After 1 minute, switch off for at least 2
minutes to allow the motor to cool down.
24. Never feed food into chute by hand. Always use the food pusher.
25. DO NOT attempt to defeat the lid interlock mechanism.
26. This appliance is not a toy. Young children should be supervised to ensure they do NOT
play with the appliance.
27. Do not operate from a timer or other remote control system
28. Do not use alkaline cleaning agents or harsh abrasives when cleaning this appliance.
29. For added safety, electrical appliances should be connected to a power outlet that is
protected by a residual current device (RCD), also often referred to as a ‘Safety Switch’.
Your switchboard may already incorporate an RCD. If unsure, call an electrician for
verication and tting if necessary.
SAVE THESE INSTRUCTIONS
THIS APPLIANCE IS FOR HOUSEHOLD USE ONLY

1
20240AU_IB&RB_FA_291113
MULTI PROCESSOR
RECIPE BOOK
20240AU
INSTRUCTIONS & WARRANTY

2
RUSSELL HOBBS and logo are Trade Marks of Spectrum Brands, Inc., or one of its subsidiaries.
©2013 Spectrum Brands, Inc.
Recipes are to be used in conjunction with the RHPC1000 Pressure Cooker by Russell Hobbs. All rights reserved. No part of this
publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording or otherwise, without prior permission of the copyright owner.
www.russellhobbs.com.au
www.russellhobbs.co.nz
SUMMER FRUITS SMOOTHIE
Preparation Time: 5 minutes
Ingredients:
4 strawberries
1 cup orange juice
1 cup pineapple juice
1 mango, peeled, seeded & diced
1 ripe banana
1 cup mango sorbet (or frozen yoghurt)
½ cup mint leaves
Method:
1. Place all ingredients in your Russell Hobbs blender blend on speed setting 3 (green) for a
further 30 seconds and serve in tall glasses.
Serves 2-3
BREAKFAST SMOOTHIE
Preparation Time: 2 minutes
Ingredients:
300ml milk
1 ripe banana, halved
12 ripe strawberries, hulled and halved
4 ice cubes
Method:
1. Place all ingredients in the blender and blend on speed setting 2 (purple) for 15 seconds.
Serves 2

3
WHITE CHOCOLATE & COCONUT MUFFINS
Preparation Time: 10 minutes
Cooking Time: 20 minutes
Ingredients:
1 ½ cups self raising our
¼ tsp cinnamon
½ cup vegetable oil
¾ cup milk
¾ cup brown sugar
1 egg
1 tsp vanilla
½ cup white chocolate buds
½ cup shredded coconut
Cooking oil spray for greasing
Method:
1. Pre-heat oven to 180°c and generously spray a 12-hole mufn tin with cooking oil spray.
2. Place dry ingredients into a large mixing bowl, make a well in the centre and set aside.
1. Place oil, milk, brown sugar, egg and vanilla into your blender and blend on speed setting 2
(purple) for 1 minute.
3. Pour the wet ingredients into the dry ingredients and gently mix with a wooden spoon until
just combined. Do not over mix.
4. Spoon a large tablespoon of the mixture into the prepared mufn tin to ¼ full and place 1
tsp of white chocolate buds in the centre. Dollop more mixture on top so that the mufns
are ¾ full. Sprinkle with a pinch of shredded coconut on top and bake for 20 minutes until
fully risen and golden brown. Cool in the mufn tin for 10 minutes before turning out onto
a cooling rack.
Tip: These mufns will keep well for up to 3 days in an airtight container.
Makes 12