Russell Hobbs Reflections RHRSP1 Installation instructions manual

RECHARGEABLE SALT & PEPPER GRINDER
MODEL RHRSP1
Instructions & Warranty RHRSP1_IB02_141209

2
Please read the instructions and keep them safe. If you pass the appliance on, pass on the
instructions too. Remove all packaging, but keep it until you know the appliance works.
IMPORTANT SAFEGUARDS
Follow basic safety precautions, including:
XThis appliance must be used by or under the supervision of a responsible adult.
XDon’t put the appliance in liquid, don’t use it in a bathroom, near water or outdoors.
X 6WRUHWKHDSSOLDQFHDZD\IURPGLUHFWVXQOLJKWDQGLISRVVLEOHIURPÀXRUHVFHQWOLJKW
XDon’t run the motor for more than 1 minute, or it may overheat. After 1 minute, switch off
for at least 3 minutes to let the motor cool.
XDon’t use the appliance for any purpose other than those directed in the instructions.
XDon’t run the appliance empty. It may overheat.
XDon’t use the appliance if it’s damaged or malfunctions.
Before operating this appliance, the following safety points should be observed:
XInspect the plugs and cords. If any damage is found, please return for replacement or
 UHSDLUE\DTXDOL¿HGHOHFWULFLDQ
XOnly use the adapter provided for this appliance.
XDo not cut the cord or use the cord to lift the appliance. Keep it away from heat sources
and wet areas.
X Do not clean the grinder while it is charging in it’s base. Please clean it while it is unplugged.
XDo not plug or unplug the power source with wet hands.
XOnly use a genuine charger from Russell Hobbs. Contact customer service if
replacement is required.
PRODUCT SPECIFICATIONS
Product name: Russell Hobbs Rechargeable Salt or Pepper Grinder
Model: RHRSP1
For use ONLY with transformer provided
Charging base input: DC 6V 500mA
Rechargeable battery: 2 x AA 1.2V 1000mAh Ni-MH (Nickel Metal Hydride) batteries
Measurement: 84mm x 84mm x 258mm
Weight: 850g approx.

3
PARTS AND ACCESSORIES TO THIS PRODUCT
a. Stainless Steel Casing h. *ULQGLQJ.QREFRDUVH¿QHSRZGHUVHOHFWLRQ
b. Control Switch i. Bulb
c. Rechargeable Battery j. Charging Jack
d. Battery Holder (irremovable) k. Charging Pilot Light (red)
e. Transparent Container l. Control Pilot Light (green)
f. Base m.Transformer (originally matched)
g. Charging Base n. Transformer Plug
b
a
c
e
d
f
g
kl
j
i
h
m
n

4
ASSEMBLING THE GRINDER (Figure 1 & 2)
1. Align the pointers on the bottom of the motor unit with the
padlocks on the top of the grinder and lower the motor unit
on to the grinder.
2. The spindle should slide easily into the centre of the motor unit.
3. Lower the cover on to the motor unit.
4. Align the pointer on the cover with the open padlock ,push
the cover down, then turn it to align the pointer with the closed
padlock .
DISMANTLING
1. Grip the cover in one hand and the grinder in the other.
2. Turn the cover to move the pointer from to .
3. Lift the cover off.
CHARGING (Figure 3)
1. Remove the grinder and components from the packaging.
2. Plug the charger cord into the charging base, plug into the
socket and switch on the mains power. (the light on the base
will illuminate).
3. Sit the grinder on the base to charge (red charging light
will illuminate).
 &KDUJLQJZLOOWDNHDSSUR[KRXUVIRUWKH¿UVWWLPH2QFHIXOO\
charged, the green charge light will illuminate.
5. For longer battery life, leave the grinder to charge for up to 8
hours continuously.
Please note: the transformer and stainless steel
casing will become warm when charging is
completed. This is normal. It is recommended that
you remove the grinder from it’s base and let it
cool slightly before using.
FILL THE GRINDER (Figure 4)
1. Lift the motor unit off the grinder.
2. Fill the grinder with peppercorns, sea salt, dried herbs or spices.
 'RQRWRYHU¿OOWKHJULQGHURULWZRQ¶W¿WWRJHWKHU
4. Align the pointers on the bottom of the motor unit with the
padlocks on the top of the grinder and lower the motor unit
onto the grinder.
5. The spindle should slide easily into the centre of the motor unit.
6. Lower the cover on to the motor unit.
7. Align the pointer on the cover with the open padlock push the
cover down, then turn it to align the pointer with the closed
padlock .
Figure 1 Figure 2
Figure 3
Figure 4

5
ADJUST THE GRIND (Figure 5)
1. Turn the whole mill upside down and turn the knob right (-) until
it won’t go any further.
2. Now turn it left (+) a little.
3. Turn the mill right way up press and release the switch.
4. Check the grind size and adjust untill it is the way you want it.
5. Don’t turn it more than 6 complete turns towards + or you may
unscrew the knob from the spindle.
CARE AND MAINTENANCE
1. Wipe the outside of the mills with a dry cloth. Do not let them get wet or damp, do not
use detergent.
2. Do not use the mills over cooking as moisture can clog the grinding mechanism.
3. Clean the contact points on both the motor unit and grinder.
4. Wipe any excess Salt or Pepper from the underneath of the grinder.
 6HWWKHULJKWJUDQXOHVL]HE\DGMXVWLQJWKHFRDUVH¿QHVHWWLQJRQWKHXQGHUQHDWKRI
the grinder
6. Ensure you are using grinder grade Salt & Pepper.
BULB REPLACEMENT
1. The bulb is wire-ended in a plastic housing.
2. You need to remove the housing from the underside of the mill.
3. Turn the whole mill upside down.
4. Grip the plastic surrounding the bulb and pull it straight up.
5. You will feel some initial resistance, then it will come out.
6. Align the wires in the replacement bulb with the contacts inside the socket underneath
the mill and push the replacement bulb fully into the socket.
Figure 5

6
GENERAL TROUBLE-SHOOTING
Problem Possible Causes Trouble-shooting
XÍ Control Pilot Light “l” on
Íthe charging base does
Ínot illuminate.
XÍ No power. XÍ Check wall socket has
Íbeen switched on.
XÍ Check plugs are properly
Íinserted into charging
Íbase and wall socket.
XÍ Charging Pilot Light “k”
Íthe charging base does
Ínot illuminate.
XÍ
Grinder not properly
Í seated in charging base .
XÍ Dirty charging contacts.
XÍ The green light is on “l”
Íbecause the battery is
Íalready fully charged.
XÍ Re-position grinder in
Ícharging base.
XÍ Clean contacts.
XÍ The grinder does not
Íoperate when the switch
Í“b” is pressed.
XÍ Improper installation of the
Ístainless steel casing and
Íthe transparent container.
XÍ Carefully align the arrow
Ísign of the stainless steel
Í
casing withÍthe transparent
Ícasing lock symbol.
XÍ The bulb on the base “i” is
Ínot lit. XÍ Burnt-out or damaged Íbulb. XÍ Replace bulb.
If your grinder does not function after checking through the items in the trouble-shooting
guide, please contact customer service.

Limited 2 year warranty
Limited 2 year warranty
Nothing in this warranty or the instructions relating to the product excludes, restricts or otherwise
affects your statutory rights under the Trade Practices Act 1974 and other relevant legislation.
In addition to your statutory rights, Salton (Aust) Pty Ltd and Salton NZ Ltd (hereafter referred to as
“Salton”) provide a LIMITED 2 YEAR WARRANTY for this product. Salton warrants this product free from
defects in material and workmanship for two (2) years from the date of purchase. Within this warranty
period Salton will repair or replace defective parts at no charge. Defective products may be returned
to Salton or the place of purchase. Salton recommends you keep your receipt as proof of purchase. If
distance prevents you from taking the product to the place of purchase, please call the Salton
customer service department freecall within Australia 1800 427 842, or freecall within New Zealand
0508 629 777.
The warranty does not cover improper installation, misuse, abuse or neglect of the product. This
warranty also does not cover any product taken apart, altered or serviced by an unauthorised repairer.
Registration of your warranty card is not compulsory, but entitles you to receive these benefits:
Information on special price offers and promotions,
Notification of any issues concerning your product.
To register your product please:
9isit www.salton.com.auwarranty 2R
)ill in the warranty card below and send it to the address shown on the back
(email address must be supplied)
Received as a gift
Prior experience with Salton
Prior experience with Russell Hobbs
Recommendation of family/friend
Recommendation of Salesperson
Product features
Salton reputation
Russell Hobbs reputation
Ease of operation
Seen in store
Seen on television
Seen in newspaper/magazine
In store demo
Special offer
RH_WC_011209