Ryobi RLT3123 User manual

RLT3123
ORIGINAL INSTRUCTIONS
Electric Line
Trimmer

Important!
It is essential that you read the instructions in this manual before assembling,
operating and maintaining the product.
Subject to technical modification.

1
Safety, performance, and dependability have
been given top priority in the design of your
electric line trimmer.
INTENDED USE
The product is only intended for use outdoors
by a standing operator.
The product is designed for cutting grass, light
weeds and other similar vegetation at or about
ground level. The cutting plane should be
approximately parallel to the ground surface.
The product should not be used to cut or trim
hedges, bushes or other vegetation where the
cutting plane is not at or about ground surface
level.
GENERAL SAFETY WARNINGS
WARNING
When using the product, the safety rules
must be followed. For your own safety
and that of bystanders, please read these
instructions before operating the product.
Please keep the instruction safe for later
use.
WARNING
This product is not intended to be used by
children or persons with reduced physical,
mental or sensory capabilities. Children
should be adequately supervised to ensure
they do not play with the product.
WARNING
Some regions have regulations that restrict
the use of the product. Check with your local
authority for advice.
TRAINING
ŶNever allow children or people unfamiliar
with these instructions to use the product.
Local regulations may restrict the age of
the operator.
ŶRead the instructions carefully. Be familiar
with all controls and the proper use of the
product.
ŶKeep bystanders, children and pets 15m
away from the area of operation. Stop the
product if anyone enters the area.
ŶNever use the product when you are tired,
ill or under the influence of alcohol, drugs
or medicine.
ŶKeep in mind that the operator or user
is responsible for accidents or hazards
occurring to other people or their property.
ELECTRICAL SAFETY
ŶPower plugs must match the outlet. Never
modify the plug in any way. Do not use
any adapter plugs with earthed (grounded)
power tools. Unmodified plugs and
matching outlets will reduce risk of electric
shock.
ŶAvoid unintentional starting. Always check
that the switch is in Off position before
plugging in the product to the power supply.
Do not carry a plugged in product with your
finger on the switch.
ŶAvoid body contact with earthed or
grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There
is an increased risk of electric shock if your
body is earthed or grounded.
ŶDo not operate the product when there is a
risk of lightning.
ŶDo not expose the product to rain or wet
conditions. Water entering an appliance
will increase the risk of electric shock.
ŶElectrical power should be supplied via
a residual current device (RCD) with a
tripping current of not more than 30 mA.
ŶBefore every use, examine the power
cord for damage. If there are signs of
damage, it must be replaced by at an
Authorized Service Centre. Always uncoil
the power cord during use, coiled cables
can overheat.
ŶIf you need to use an extension cable
ensure it is suitable for outdoor use and
has a current capacity sufficient to supply
your product. The extension cord cable
should be marked with either “H05 RN-
F” or H05 VV-F”. Check it before every
use for damage, always uncoil it during
use because coiled cables can overheat.
Damaged extension cables should not be
repaired, they should be replaced with an
equivalent type.
ŶDo not use the product if the electric cables
are damaged or worn.
ŶIf the power cord or extension cable
becomes damaged during use, disconnect

2
from the power supply immediately. Do not
touch the electric cables until the power
supply has been disconnected.
ŶMake sure the power cord is positioned so
that it cannot be damaged by the cutting
means and will not be stepped on, tripped
over or otherwise subjected to damage or
stress.
ŶNever pick up or carry the product by the
electric cable.
ŶNever pull by the power cord to disconnect
from the power supply.
ŶKeep the power cord away from heat, oil
and sharp edges.
ŶMake sure voltage is correct for your
product. A nameplate on the product
indicates the product’s voltage. Never
connect the product to an AC voltage that
differs from this voltage.
ŶMake sure the switch is in Off position
before disconnecting from power supply.
PREPARATION
ŶWear full eye and hearing protection while
operating the product. If working in an area
where there is a risk of falling objects, head
protection must be worn.
ŶHearing protection may restrict the
operators ability to hear warning sounds,
pay particular attention to potential hazards
around and inside the working area.
ŶWear heavy long trousers, boots, and
gloves. Do not wear loose fitting clothing,
short trousers, jewellery of any kind, or use
with bare feet.
ŶSecure long hair so it is above shoulder
level to prevent entanglement in moving
parts.
ŶBefore use and after any impact, check that
there are no damaged parts. A defective
switch or any part that is damaged or worn
should be properly repaired or replaced by
an authorized service facility.
ŶMake sure the cutting attachment is
properly installed and securely fastened.
ŶNever operate the product unless all
guards, deflectors and handles are properly
and securely attached.
ŶConsider the environment in which you are
working. Keep the working area free from
wires, sticks, stones and debris which if
struck by the cutter can become thrown
objects.
LINE TRIMMER SAFETY WARNINGS
ŶNever allow children, persons with reduced
physical, sensory or mental capabilities
or lack of experience and knowledge or
people unfamiliar with these instructions
to use the product. Local regulations may
restrict the age of the operator.
ŶUse the product in daylight or good artificial
light.
ŶAvoid using on wet grass.
ŶKeep proper footing and balance at all
times.
ŶDo not walk backwards when using the
product.
ŶKeep firm footing and balance. Do not
overreach. Overreaching can result in loss
of balance. Always be sure of the footing
on slopes, and walk, never run.
ŶKeep bystanders, children and pets 15m
away from the area of operation, stop the
product if anyone enters the area.
ŶKeep the cutting attachment below waist
level.
ŶNever operate the product with damaged
guards or without guards in place.
ŶNever fit a metal replacement line.
ŶKeep hands and feet away from the cutting
means at all times and especially when
switching on the motor.
ŶBeware, the cutting elements continue to
rotate after the motor is switched off.
ŶBeware of objects thrown by the cutting
means. Clear debris like small stones,
gravel and other foreign objects from the
work area before starting operation. Wires
or string may become entangled with the
cutting means.
ŶSwitch off and disconnect from the power
supply before:
Ɣservicing
Ɣleaving the product unattended
Ɣcleaning your product or clearing a
blockage
Ɣchanging accessories
Ɣchecking for any damage after hitting an
object
Ɣchecking for any damage if the product

3
starts to vibrate abnormally
Ɣperforming maintenance
ŶThe small blade fitted to the lawn guard
is designed to trim the new extended line
to the correct length for safe and optimum
performance. It is very sharp, do not touch
it particularly when cleaning the product.
ŶAlways ensure that ventilation openings
are kept clear of debris.
ŶMake sure the cutting head attachment is
properly installed and securely fastened.
ŶMake sure all guards, deflectors and
handles are properly and securely
attached.
ŶDo not modify the product in any way, this
may increase the risk of injury to yourself
or others.
ŶUse only the manufacturer’s replacement
cutting line. Do not use any other cutting
attachment.
ŶImmediately switch off and disconnect from
the mains once in the event of accident
or breakdown. Don’t operate the product
again until it’s fully checked by authorised
service center.
TRANSPORTATION AND STORAGE
ŶStop the product and allow it to cool before
storing or transporting.
ŶClean all foreign material from the product.
Store it in a cool dry and well-ventilated
place that is inaccessible to children.
Keep away from corrosive agents such as
garden chemicals and de-icing salts. Do
not store outdoors.
ŶFor storage, always disconnect from power
supply and wind cable.
ŶFor transportation, secure the product
against movement or falling to prevent
injury to persons or damage to the product.
MAINTENANCE
WARNING
Use only original manufacturer’s
replacement parts, accessories and
attachments. Failure to do so can cause
possible injury, poor performance and may
void your warranty.
WARNING
Servicing requires extreme care and
knowledge and should be performed
RQO\ EH D TXDOL¿HG VHUYLFH WHFKQLFLDQ )RU
service we suggest you return the product
to your nearest authorized service center for
repair. When servicing, use only identical
replacement parts.
ŶSwitch off and disconnect from the mains
before: conducting any maintenance or
cleaning work.
ŶYou may make adjustments and repairs
described here. For other repairs, contact
the authorized service agent.
ŶFor replacement line use only nylon
filament line of the diameter described in
the specification table of this manual
ŶAfter extending new cutter line, always
return the product to its normal operating
position before starting.
ŶAfter each use, clean the product with a
soft dry cloth. Any part that is damaged
should be properly repaired or replaced by
an authorized service centre.
ŶCheck all nuts, bolts and screws at frequent
intervals for proper tightness to ensure the
product is in safe working condition.
RESIDUAL RISKS
Even when the product is used as prescribed,
it is still impossible to completely eliminate
certain residual risk factors. The following
hazards may arise in use and the operator
should pay special attention to avoid the
following:
ŶInjury caused by vibration. Hold the product
by designated handles and restrict working
time and exposure.
ŶExposure to noise can cause hearing injury.
Wear ear protection and limit exposure.
ŶEye injury due to flying debris. Wear eye
protection at all times.
RISK REDUCTION
It has been reported that vibrations from
hand-held products may contribute to a
condition called Raynaud’s Syndrome in
certain individuals. Symptoms may include
tingling, numbness and blanching of the
¿QJHUV XVXDOO\ DSSDUHQW XSRQ H[SRVXUH WR

4
cold. Hereditary factors, exposure to cold and
dampness, diet, smoking and work practices
are all thought to contribute to the development
of the these symptoms. There are measures
that can be taken by the operator to possibly
reduce the effects of vibration:
ŶKeep your body warm in cold weather.
When operating the product wear gloves
to keep the hands and wrists warm. It is
reported that cold weather is a major factor
contributing to Raynaud’s Syndrome.
ŶAfter each period of operation, exercise to
increase blood circulation.
ŶTake frequent work breaks. Limit the
amount of exposure per day.
If you experience any of the symptoms of this
condition, immediately discontinue use and
see your doctor about these symptoms.
WARNING
Injuries may be caused, or aggravated, by
prolonged use of a tool. When using any
tool for prolonged periods, ensure you take
regular breaks.
KNOW YOUR PRODUCT
See page 7.
1. Rear handle
2. Trigger
3. Front handle
4. Cord retainer
5. Pivoting button
6. Upper shaft
7. Lower shaft
8. Safety guard
9. Cutting line
10. Cut-off blade
11. Spool cover
12. Eyelet
13. Spool cover lock button
14. Bump head
15. Spool
SYMBOLS ON THE PRODUCT
Read and understand all
instructions before operating
the product, follow all warnings
and safety instructions.
Wear eye protection.
Wear hearing protection.
Do not use metal blade(s) on
the product.
Do not expose to rain or damp
condition.
Remove plug from the
mains immediately before
maintenance or if cable is
damaged, cut or entangled.
%HZDUHRIWKURZQRUÀ\LQJ
objects.
Keep all bystanders a safe
distance away from the
product.
%HZDUHRIWKURZQRUÀ\LQJ
objects. Keep all bystanders,
especially children and pets,
at least 15m away from the
operating area
Keep hands away from cut-off
blade
Class II tool, double insulation
Waste electrical products
should not be disposed of
with household waste. Please
recycle where facilities exist.
Check with your Local Authority
or retailer for recycling advice.
Conforms to all regulatory
standards in the country in
the EU where the product is
purchased.
EurAsian Conformity Mark
96
Guaranteed sound power level
is 96 dB.
The following signal words and meanings
are intended to explain the levels of risk
associated with this product:
The following signal words and meanings

5
are intended to explain the levels of risk
associated with this product.
DANGER
Indicates an imminently hazardous
situation, which, if not avoided, will result in
death or serious injury.
WARNING
Indicates a potentially hazardous situation,
which, if not avoided, could result in death
or serious injury.
CAUTION
Indicates a potentially hazardous situation,
which, if not avoided, may result in minor or
moderate injury.
CAUTION
Without safety alert symbol
Indicates a situation that may result in
property damage.
SYMBOLS IN THIS MANUAL
Connect to power outlet.
Disconnect from power outlet.
Parts or accessories sold
separately
Note
Warning

6
x 1
x 1
x 1
x 2x 1x 1

7
1
4
5
6
7
23
10
8
9
11
12
13
15
14

8
1
23
1 2
5 6

9
1
2
3
1
2
3 4
7 8

10
p.11
p.14 p.16
p.15

11

12
1
2
2
1

13
1
2
3

14
2
3
1
1
3
2
2
1
1
2
3
4

15
1
2

16
20151118v1
1
2

PRODUCT SPECIFICATIONS
Electric Line Trimmer
Rated power 300 W
Rated voltage 230-240V ~ 50Hz
No-load speed 12,000 min-1
Cutting line diameter 1.2 mm
Cutting capacity 23 cm
Vibration level (in accordance with EN 786 Annex D)
Rear handle 5.5 m/s2
Front handle 3.2 m/s2
Uncertainty of measurement 1.5 m/s2
Noise emission level (in accordance with EN 786 Annex E)
A-weighted sound pressure level at
operator’s position
80.5 dB(A)
Uncertainty of measurement 2.5 dB
A-weighted sound power level 93.7 dB(A)
Uncertainty of measurement 1.09 dB
Weight 1.4 kg
REPLACEMENT PART
1.2 mm complete spool RAC118 (5132002590)
1.2 mm spool (3 pcs) RAC119 (5132002591)

GUARANTEE
In addition to any statutory rights resulting from the purchase, this product is covered by a guarantee as stated below.
1. The guarantee period is 24 months for consumers and commences on the date when the product was purchased.
This date has to be documented by an invoice or other proof of purchase. The product is designed and dedicated to
consumer and private use only. So there is no guarantee provided in case of professional or commercial use.
2. There is, in some cases (i.e. promotion, range of tools), a possibility to extend the warranty period over the period
described above using the registration on the www.ryobitools.eu website. The eligibility of the tool is clearly displayed
in stores and/or on packaging. The end user needs to register his/her newly-acquired tools online within 8 days from
the date of purchase. The end user may register for the extended warranty in his country of residence if listed on the
online registration form where this option is valid. Furthermore, end users must give their consent to the storage of the
data which are required to enter online and they have to accept the terms and conditions. The registration confirmation
receipt, which is sent out by e-mail, and the original invoice showing the date of purchase will serve as proof of the
extended warranty. Your statutory rights remain unaffected.
3. The guarantee covers all defects of the product during the warranty period due to defaults in workmanship or material
at the purchase date. The guarantee is limited to repair and/or replacement and does not include any other obligations
including but not limited to incidental or consequential damages. The warranty is not valid if the product has been
misused, used contrary to the instruction manual, or being incorrectly connected. This guarantee does not apply to:
–any damage to the product that is the result of improper maintenance
–any product that has been altered or modified
–any product where original identification (trade mark, serial number) markings have been defaced, altered or
removed
–any damage caused by non-observance of the instruction manual
–any non CE product
–any product which has been attempted to be repaired by an non-qualified professional or without prior authorization
by Techtronic Industries
–any product connected to improper power supply (amps, voltage, frequency)
–any product used with inappropriate fuel mixture (fuel, oil, percentage of oil)
–any damage caused by external influences (chemical, physical, shocks) or foreign substances
–normal wear and tear of spare parts
–inappropriate use, overloading of the tool
–use of non-approved accessories or parts
–carburettor after 6 months, carburettor adjustments after 6 months
–components (parts and accessories) subject to natural wear and tear, including but not limited to bump knobs, drive
belts, clutch, blades of hedge trimmers or lawn mowers, harness, cable throttle, carbon brushes, power cord, tines,
felt washers, hitch pins, blower fans, blower and vacuum tubes, vacuum bag and straps, guide bars, saw chains,
hoses, connector fittings, spray nozzles, wheels, spray wands, inner reels, outer spools, cutting lines, spark plugs,
air filters, gas filters, mulching blades, etc.
4. For servicing, the product must be sent or presented to a RYOBI authorized service station listed for each country in the
following list of service station addresses. In some countries your local RYOBI dealer undertakes to send the product
to the RYOBI service organisation. When sending a product to a RYOBI service station, the product should be safely
packed without any dangerous contents such as petrol, marked with sender’s address and accompanied by a short
description of the fault.
5. A repair/replacement under this guarantee is free of charge. It does not constitute an extension or a new start of the
guarantee period. Exchanged parts or tools become our property. In some countries delivery charges or postage will
have to be paid by the sender.
6. This guarantee is valid in the European Community, Switzerland, Iceland, Norway, Liechtenstein, Turkey and Russia.
Outside these areas, please contact your authorized RYOBI dealer to determine if another warranty applies.