Ryobi RY253SS User manual

First Time Start
First Time Assembly
Remove product from carton.
Assemble per instructions
in your operator’s manual.
1
WARNING: This Quick Start Guide is not a substitute for reading the
operator’s manual. To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
2
4
Align and assemble 2 booms
until fully seated.
Snap shield into place over boom and bracket.
Secure with bolt and wing nut as shown.
3
Spread handle over boom and
snap into place. Secure with
bolt and wing nut.
- OR -
Curved Shaft
Straight Shaft
Mix 2.6 oz. 2-cycle oil with
1 gallon of fresh gasoline in
separate gas container. Shake,
then pour into trimmer tank.
5
6
8
7
Place trimmer on ground
with the trim head end facing
away from you.
Set choke lever to
FULL CHOKE position.
Repeatedly press the primer
bulb 10 times.
SQUEEZE THROTTLE
TRIGGER FULLY and pull
starter grip and rope until
engine attempts to start (no
more than 4x).
NOTE: If engine does not
start, return to step 7 and
repeat.
9
SET TO HALF CHOKE position.
11
12
SQUEEZE THROTTLE
TRIGGER FULLY and pull
starter grip until engine
runs. Allow engine to run
10 seconds, set to RUN
position.
You are now ready to Trim!
If engine did not start,
REPEAT STEPS
To stop trimmer, press
the red switch located
on the top of the
trigger housing.
Go to www.ryobitools.com and register your new tool online.
For any questions about operating or maintaining your product,
call the Ryobi™Help Line!
1-800-860-4050
Your Product has been fully tested prior to shipment to
ensure your complete satisfaction. Troubleshooting tips are
also available in your operator’s manual.
For additional registration instruction, refer to operator’s manual.
10X
TRIM!
10
991000348
1-14-15 (REV:01)
7
–
11

First Time Start
First Time Assembly
Remove product from carton.
Assemble per instructions
in your operator’s manual.
1
WARNING: This Quick Start Guide is not a substitute for reading the
operator’s manual. To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
2
4
Align and assemble 2 booms
until fully seated.
Snap shield into place over boom and bracket.
Secure with bolt and wing nut as shown.
3
Spread handle over boom and
snap into place. Secure with
bolt and wing nut.
- OR -
Curved Shaft
Straight Shaft
Mix 2.6 oz. 2-cycle oil with
1 gallon of fresh gasoline in
separate gas container. Shake,
then pour into trimmer tank.
5
6
8
7
Place trimmer on ground
with the trim head end facing
away from you.
Set choke lever to
FULL CHOKE position.
Repeatedly press the primer
bulb 10 times.
SQUEEZE THROTTLE
TRIGGER FULLY and pull
starter grip and rope until
engine attempts to start (no
more than 4x).
NOTE: If engine does not
start, return to step 7 and
repeat.
9
SET TO HALF CHOKE position.
11
12
SQUEEZE THROTTLE
TRIGGER FULLY and pull
starter grip until engine
runs. Allow engine to run
10 seconds, set to RUN
position.
You are now ready to Trim!
If engine did not start,
REPEAT STEPS
To stop trimmer, press
the red switch located
on the top of the
trigger housing.
Go to www.ryobitools.com and register your new tool online.
For any questions about operating or maintaining your product,
call the Ryobi™Help Line!
1-800-860-4050
Your Product has been fully tested prior to shipment to
ensure your complete satisfaction. Troubleshooting tips are
also available in your operator’s manual.
For additional registration instruction, refer to operator’s manual.
10X
TRIM!
10
991000348
1-14-15 (REV:01)
7
–
11

First Time Start
First Time Assembly
Remove product from carton.
Assemble per instructions
in your operator’s manual.
1
WARNING: This Quick Start Guide is not a substitute for reading the
operator’s manual. To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
2
4
Align and assemble 2 booms
until fully seated.
Snap shield into place over boom and bracket.
Secure with bolt and wing nut as shown.
3
Spread handle over boom and
snap into place. Secure with
bolt and wing nut.
- OR -
Curved Shaft
Straight Shaft
Mix 2.6 oz. 2-cycle oil with
1 gallon of fresh gasoline in
separate gas container. Shake,
then pour into trimmer tank.
5
6
8
7
Place trimmer on ground
with the trim head end facing
away from you.
Set choke lever to
FULL CHOKE position.
Repeatedly press the primer
bulb 10 times.
SQUEEZE THROTTLE
TRIGGER FULLY and pull
starter grip and rope until
engine attempts to start (no
more than 4x).
NOTE: If engine does not
start, return to step 7 and
repeat.
9
SET TO HALF CHOKE position.
11
12
SQUEEZE THROTTLE
TRIGGER FULLY and pull
starter grip until engine
runs. Allow engine to run
10 seconds, set to RUN
position.
You are now ready to Trim!
If engine did not start,
REPEAT STEPS
To stop trimmer, press
the red switch located
on the top of the
trigger housing.
Go to www.ryobitools.com and register your new tool online.
For any questions about operating or maintaining your product,
call the Ryobi™Help Line!
1-800-860-4050
Your Product has been fully tested prior to shipment to
ensure your complete satisfaction. Troubleshooting tips are
also available in your operator’s manual.
For additional registration instruction, refer to operator’s manual.
10X
TRIM!
10
991000348
1-14-15 (REV:01)
7
–
11