SAFAVIEH COUTURE Emerson SFV4753-K User manual

CARE AND MAINTENANCE
NOTICE
4X
BEar of Headboard(L&R) 2X
2X
C 1X
Part List and Hardware List
PIECE DESCRIPTION PICTURE
QUANTITY
SAFAVIEH
1X
2X
AHeadboard 1X
Spot clean using a mild water-free solvent. Only a professional cleaner should
undertake a complete overall cleaning.
The use of steam or water-based cleaners may cause excessive shrinking or
staining.
* Please make sure that you have all parts indicated before you begin assembly of
this item
* This item should be assembled on a soft surface to prevent scratching the finish
during assembly
* This item may require periodic tightening
Dimensions: 89.6"WX87.4"DX50.8"H
Weight Capacity: 825 lbs
C O U T U R E
Bed Legs
H Support Leg for Cross Slat 4X
Cross Slat
WARNING: DO NOT STAND ON BED
WARNING: DO NOT OVER TORQUE BOLTS/SCREWS
SFV4753-K
HW6
1X
Slat
D
E
F
G
HW1
HW2
HW5 Allen Key
Phillips Screws 4*2*30MM
1X
Wrench
6X
6X
Split Lock Washer(M8)
Flat Washer(M8)
Socket Screws 8*1.25*30MM
HW3
HW4
12X
6X
Sideboard
The legs and hardware are located inside the sideboard&slat boxs.
Footboard

PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list.
If any partismissing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 15minutes.
Tools Required for Assembly (included): Allen key/wrench
PREARATION
H1
Assembl the slat legs"H" with part ofAssembl the slat legs"H" with part ofAssembl the slat legs"H" with part of Assembl the slat legs"H" with part of
HW5
HW2
HW3
HW4
STEP2
Rotate the bed legs E to the footboard C
and headboard(Step 1).
STEP4 Rotate the slat legs H to the middle rod of slat
G. Put it inside the middle of the bed, And then,
smooth the slat F inside the bed
G
H
F
CE
E
STEP3 Attach the sideboard D with headboard and
footboard(Step2) by sliding the iron plates onto
the bolts, the metal card should be alignment card slot
when install it,then press it lightly.
X2
X2
The legs and hardware are located inside the sideboard&slat boxs.
The legs and hardware are located inside the sideboard&slat boxs.
HW6
HW6
STEP5
Secure the slat with screw HW1 by using
wrench HW6.There are totally 12 holes on slat
to make sure it stable, it's shown in step 4
It's finished as shown,Your Bed is
ready for use.
X2
STEP1 Open the velcro on the headboard A, attach the ear
of headboard B to the headboard A by using allen key HW5
and hardware HW2, HW3, HW4 as shown, tighten until
secure, Then smooth the velcro.
B/L
B/R

CARE AND MAINTENANCE
NOTICE
4X
BEar of Headboard(L&R) 2X
2X
C 1X
Part List and Hardware List
PIECE DESCRIPTION PICTURE
QUANTITY
SAFAVIEH
1X
1X
AHeadboard 1X
Spot clean using a mild water-free solvent. Only a professional cleaner should
undertake a complete overall cleaning.
The use of steam or water-based cleaners may cause excessive shrinking or
staining.
* Please make sure that you have all parts indicated before you begin assembly of
this item
* This item should be assembled on a soft surface to prevent scratching the finish
during assembly
* This item may require periodic tightening
Dimensions: 73.8"WX87.4"DX50.8"H
Weight Capacity: 825 lbs
C O U T U R E
Bed Legs
H Support Leg for Cross Slat 2X
Cross Slat
WARNING: DO NOT STAND ON BED
WARNING: DO NOT OVER TORQUE BOLTS/SCREWS
SFV4753-Q
HW6
1X
Slat
D
E
F
G
HW1
HW2
HW5 Allen Key
Phillips Screws 4*2*30MM
1X
Wrench
6X
6X
Split Lock Washer(M8)
Flat Washer(M8)
Socket Screws 8*1.25*30MM
HW3
HW4
9X
6X
Sideboard
The legs and hardware are located inside the sideboard&slat boxs.
Footboard

PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list.
If any partismissing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 15minutes.
Tools Required for Assembly (included): Allen key/wrench
PREARATION
H1
Assembl the slat legs"H" with part ofAssembl the slat legs"H" with part ofAssembl the slat legs"H" with part of Assembl the slat legs"H" with part of
HW5
HW2
HW3
HW4
STEP2
Rotate the bed legs E to the footboard C
and headboard.
STEP4 Rotate the slat legs H to the middle rod of slat
G. Put it inside the middle of the bed, And then,
smooth the slat F inside the bed
HGF
CE
E
STEP3 Attach the sideboard D with headboard and
footboard(Step2) by sliding the iron plates onto the bolt,
the metal card should be alignment card slot when
install it,then press it lightly.
X2
X2
The legs and hardware are located inside the sideboard&slat boxs.
The legs and hardware are located inside the sideboard&slat boxs.
HW6
HW6
STEP5
Secure the slat with screw HW1 by using
wrench HW6.There are totally 9 holes on slat
to make sure it stable, it's shown in step 4
It's finished as shown,Your Bed is
ready for use.
STEP1 Open the velcro on the headboard A, attach the ear
of headboard B to the headboard A by using allen key HW5
and hardware HW2, HW3, HW4 as shown,tighten until
secure, Then smooth the velcro.
B/L
B/R