Safavieh Furniture AMH8503A User manual

PIECE DESCRIPTION QUANTITY PIECE DESCRIPTION QUANTITY
A TABLE TOP 1X HW1 SPANNER 1X
B TABLE LEG (2 LEFT & 2 RIGHT) 4X HW2 HEX NUT 5/16 8X
C TABLE SHORT CROSSBAR 2X HW3 LOCK WASHER 5/16 8X
D TABLE LONG CROSSBAR 1X HW4 FLAT WASHER 5/16 8X
E LEG FRAME 6X HW5 WOOD SCREW M4 X 38MM 6X
F STOOL SEAT 2X HW6 WOOD SCREW M7 X 50MM 24X
G STOOL STRETCHER 4X HW7 ALLEN WRENCH M4 1X
H BENCH SEAT 1X HW8 WOOD PLUG 24X
I BENCH STRETCHER 2X
PICTURE
PRODUCT DIMENSION: 24"W X 44"L X 36"H
WARNING: DO NOT STAND ON CHAIR
Weight Capacity: 225LBS
Part List and Hardware List
NOTICE
* Please make sure that you have all parts indicated and they are in good condition before you begin assembly of
this item. Refer to part list and hardware list below for guidance.
* This item should be assembled on a soft surface to prevent scratching the finish during assembly.
* This item may require periodic tightening.
* If you are having difficulty, our friendly Customer Care team is always here to help. Please email
[email protected]om
PREPARATION
* Before beginning assembly of product, make sure all parts are present. Compare parts with part contents list
and hardware contents list.
* If any part is missing or damaged, do not attempt to assemble the product.
* Estimated Assembly Time: 10 minutes.
* Tools Required for Assembly (included): None
CARE AND MAINTENANCE
Adhesive felt pads should always be applied to areas of furniture which make direct contact with flooring, said
application will prevent damage to the furniture and or surfaces on which the furniture lies. Objects placed on
articles of furniture should rest on non abrasive material as to prevent damage to the wood finish. Objects whose
composition consist of plastic and rubber are known to discolor and damage the wood surfaces on which they
rest. Wipe up spills immediately and avoid common hazards such as hot dishes, harsh solvents and abrasives.
Cleaning should be done with a soft lint free cotton cloth dampened with water or furniture polish. On highly
used surfaces we recommend applying a quality paste wax which should be used on a regular basis to provide
additional protection from scratches and spills. How often you apply the wax depends on how much the furniture
wears.
PICTURE
ITEM ID: AMH8503A/B/C/D

STEP 3: Align and fasten leg frame (E) to seat (F) using screw
(HW6) and tighten with Allen wrench (HW7).
STEP 6: Insert wood plug (HW8) into the hole on the leg.
PREPARATION
* Before beginning assembly of product, make sure all parts are present. Compare parts with part contents list and hardware contents list.
* If any part is missing or damaged, do not attempt to assemble the product.
* Estimated Assembly Time: 10 minutes.
* Tools Required for Assembly (included): None
* If you are having difficulty, our friendly Customer Care team is always here to help. Please email [e-mail]
STEP 1: Attach Table Leg (B Right & left) to Table Top (A) table
short crossbar (C) using Flat Washer (HW4), Lock Washer (HW3)
and Hex Nut (HW2) with Spanner (HW1).
STEP 2: Repeat Step 1 to assemble the other three legs (B). Attach the
table long crossbar (D) to the table short crossbar (C ).
STEP 4: Align and fasten stretcher (G) to leg frame (E) using
screw (HW6) and tighten with Allen wrench (HW7).
STEP 5: Align and fasten the other leg frame (E) to stretcher and seat
(F) using screw (HW6) and tighten with Allen wrench (HW7).
A
B (RIGHT) B (LEFT)
HW5
HW1
HW2
HW3
HW4
HW1
HW2
HW3
HW4
HW5
HW5
HW6
HW6
D
F
E
HW6
HW6
HW8
G
C
E
HW6
HW6
HW6
HW6

STEP 9: Line up of second leg frame (E) with screw holes on
bottom of Bench Top (H) and attach using JCBC screw (HW6).
Do not tighten these screw all the way until you insert the
Cross Bar (I) when all holes are aligned. Tighten all remaining
screw.
STEP 10: Do not tighten screw until fully assembled and level.
Insert wood bottom (HW8) into every screw hole in leg.
Complete.
STEP 7: Place seat upside down smooth carpeter surface. Line
up legs of leg frame (E) with screw holes on bottom of Bench
Top (H) and attach with using JCBC screw(HW6).
STEP 8: Insert cross bar (I) into leg frame (E) and secure with JCBC
screw (HW6).
HW8
HW8
HW8
HW8
HW8
HW8
HW8
HW8
HW6
HW6
HW6
HW6
HW6
HW6
HW6
HW6
E
H
EII
EE