Safavieh Furniture AMH8504A User manual

ITEM ID: AMH8504A/B/C/D
PIECE DESCRIPTION QUANTITY PIECE DESCRIPTION QUANTITY
A TABLE TOP 1X HW1 SHORT BOLT M6 X 35MM 4X
B TOP PANEL 1X HW2 LONG BOLT M6 X 60MM 8X
CBOTTOM PANEL 1X HW3 LOCK WASHER 1/4 12X
D TABLE LEG FRAME 2X HW4 FLAT WASHER 1/4 12X
E VERTICAL PANEL 2X HW5 ALLEN WRENCH M4 2X
F HORIZONTAL PANEL 3X HW6 WOOD SCREW M7 X 50MM 16X
G CHAIR LEG FRAME 4X HW7 WOOD PLUG 16X
H CHAIR SEAT 2X HW8 LEG STOPPER M6 X 23MM 4X
I STRETCHER 4X
Weight Capacity: 225LBS
WARNING: DO NOT STAND ON CHAIR
PICTURE
PRODUCT DIMENSION: 36"W X 36"L X 36"H
NOTICE
* Please make sure that you have all parts indicated and they are in good condition before you begin assembly of
this item. Refer to part list and hardware list below for guidance.
* This item should be assembled on a soft surface to prevent scratching the finish during assembly.
* This item may require periodic tightening.
* If you are having difficulty, our friendly Customer Care team is always here to help. Please email
[e-mail]
PREPARATION
* Before beginning assembly of product, make sure all parts are present. Compare parts with part contents list
and hardware contents list.
* If any part is missing or damaged, do not attempt to assemble the product.
* Estimated Assembly Time: 10 minutes.
* Tools Required for Assembly (included): None
CAREANDMAINTENANCE
Adhesive felt pads should always be applied to areas of furniture which make direct contact with flooring, said
application will prevent damage to the furniture and or surfaces on which the furniture lies. Objects placed on
articles of furniture should rest on non abrasive material as to prevent damage to the wood finish. Objects whose
composition consist of plastic and rubber are known to discolor and damage the wood surfaces on which they
rest. Wipe up spills immediately and avoid common hazards such as hot dishes, harsh solvents and abrasives.
Cleaning should be done with a soft lint free cotton cloth dampened with water or furniture polish. On highly
used surfaces we recommend applying a quality paste wax which should be used on a regular basis to provide
additional protection from scratches and spills. How often you apply the wax depends on how much the
furniture wears.
PartListandHardwareList
PICTURE
RED MARK

STEP 3:
Place the assembled wine rack into the leg frame (D)
from step 2.
PREPARATION
* Before beginning assembly of product, make sure all parts are present. Compare parts with part contents list and hardware contents list.
* If any part is missing or damaged, do not attempt to assemble the product.
* Estimated Assembly Time: 10 minutes.
* Tools Required for Assembly (included): None
* If you are having difficulty, our friendly Customer Care team is always here to help. Please email [email protected]
STEP 1: Align and insert the vertical panel (E) into the slot on
the horizontal panel (F).
STEP 2: Align and fasten top panel (B) to leg frame (D) using long bolt
(HW2), lock washer (HW3) and flat washer (HW4), then tighten with
Allen wrench (HW5) (DO NOT TIGHTEN YET).
STEP 4: Align and fasten the other leg frame (D) to top panel (B)
using long bolt (HW2), lock washer (HW3), flat washer (HW4)
and tighten with Allen wrench (HW5) (DO NOT TIGHTEN YET).
Remark: push the wine rack towards the bottom of leg frame
when assemble the other leg frame with top panel.
STEP 5: Place the partially assembled table base upside down on soft
surface Align and fasten bottom panel (C) to leg frames (D) using long
bolt (HW2), lock washer (HW3), flat washer (HW4) and tighten with
Allen wrench (HW5). Press top (B) & bottom(C) panal. Tighten all
screws while pressing the Top (B) to bottom(C).
STEP 6: Place the table on the floor. Align and fasten table top
(A) to table base using short bolt (HW1), lock washer (HW3),
flat washer (HW4) and tighten with Allen wrench (HW5).
Remark: push the wine rack towards the bottom (C) of leg
frame (D) when assemble the other leg frame (D) with top
panel (B).
E
F
B
D
HW2
HW5
HW3
HW4
DCHW5
HW2
HW3
HW4
HW5
HW1
HW3
HW4
A

STEP 9: Align and fasten stretcher to leg frame (G) using screw
(HW6) and tighten with Allen wrench (HW5).
Complete.STEP 10: Align and fasten the other leg frame (G) to stretcher (I)
and seat (H) using screw (HW6) and tighten with Allen wrench
(HW5).
STEP 11: Insert wood plug (HW7) into the hole on the leg.
STEP7: Tight all the screw from step 2 to step 5. Insert leg
stopper (HW8) on bottom of table leg.
STEP 8: Align and fasten leg frame (G) to seat (H) using screw (HW6)
and tighten with Allen wrench (HW5).
HW7
I
HW6
HW6
HW6 HW6
G
H
HW5
HW2
HW3
HW4
HW8
HW6
HW6
HW6 HW6
IG
H
G
G
H
I
I