Safety Vision 47 SERIES User manual

47 SERIES IP CAMERA
USER GUIDE

Important Notices
Title: 47 Series IP Camera User Guide
Document Version: 1
Revision: 0
PN: 47-xxIR-IP
Safety Vision attempts to provide information contained in this manual based
on the latest product information available at the time of publication. However,
because of Safety Vision’s policy of continual product improvement, Safety Vision
reserves the right to amend the information in this document at any time without
prior notice.
This material is confidential and the property of Safety Vision. It is shared with
your company for the sole purpose of helping you with the operation of the
described equipment.
Safety Vision makes no warranty of any kind with regard to this material,
including, but not limited to, the implied warranties of merchantability and fitness
for a particular purpose. Safety Vision shall not be liable for errors contained
herein or for incidental or consequential damages in connection with the
furnishing, performance, or use of this material.
Safety Vision expressly disclaims all responsibility and liability for the installation,
use, performance, maintenance, and support of third-party products. Customers
are advised to make their independent evaluation of such products.
No part of this document may be photocopied, reproduced, or translated to
another language without the prior written consent of Safety Vision.
Safety Vision® is a registered trademark of Safety Vision, LLC. All other products
or name brands mentioned in this document are trademarks of their respective
owners. For more information about Safety Vision and its products, go to www.
safetyvision.com or call 800-880-8855.

47 SERIES IP CAMERA
Features 1
Parts Included 1
Overview 2
Cables Description 3
Installation 4
Memory Card Installation 5
Camera Mounting 6
Installation of Network Cable Water-proof Jacket (Optional) 7
Waterproof Jacket Components 7
Conguration 9
Camera Initialization 9
Modify IP Address 10
Accessing via Web Browser 11
Specications 12
Dimensions 13
FCC Compliance Statement 14
Contents

1
47 SERIES IP CAMERA
Features
• 3-axis gimbal provides exible mounting opportunities
• 10 IR illuminators for low lighting conditions
• IP67 rating ensures protection from dust and water
• Integrated microphone
Parts Included
• 47 Series IP Camera
• Quick Start Guide
• Mounting Template
• Waterproof Connector
• Screw Package
• Wrench (optional)
• CD

247 SERIES IP CAMERA
1 - Fastener Anchors
2 - Camera Base
3 - Self-tapping Screws
4 - Dome Cover
5 - Locking Screws
Overview

3
47 SERIES IP CAMERA
Cables Description
The following describes the dierent connectors that may be encountered on this
camera series.
1 - Power Input - Input power, connect to DC 12V power, and please be sure to
power the device according to the instruction of device label.
2 - Network port - Network data transmission and Power over Ethernet (PoE)
power supply.

447 SERIES IP CAMERA
Installation
Before you start:
• Ensure the camera is in good condition and all accessories
were included.
• Ensure the mounting surface is sufficient to support the weight
of the camera.
• Implement this step when it needs to use microSD card and there is a SD
card slot for the device.
• Turn off the device power before installing microSD card.
For cameras that feature infrared illuminators (IRs):
• Dust or grease on the dome may cause IR reflections in the image.
Do not remove the dome cover film until the installation
is complete.
• Ensure there are no reflective surfaces close to the camera lens.
• The foam ring around the lens must be seated flush against the inner
surface of the dome to isolate the lens from the IRs.

5
47 SERIES IP CAMERA
Memory Card Installation
The 47 series IP cameras supports microSD card for local storage. Use the
following procedure to mount the memory card.
1. Remove camera dome cover.
Using a T15 TORX™, loosen the 2 locking screws and remove
dome cover.
2. Release microSD card.
Lightly push down on the microSD card until a “click” is felt, then allow it to
spring out of the slot.
3. The microSD card partly ejects.
4. Pull the microSD card straight out.
Reinsert the microSD card in the same manner: push it straight in until a “click” is
felt, then release.
NOTE - Press the Reset Button for approximately 10 seconds while the camera is
powering on to restore the default settings.

647 SERIES IP CAMERA
Camera Mounting
Use the following procedure to install the 47 series camera:
1. Clean the area where the camera is to be installed.
2. Mark mounting and cable exit hole locations.
Use the included adhesive template and mark the four mounting screw holes
and cable exit hole in the desired mounting location.
3. Drill cable exit hole.
Use a hole saw or appropriate drill bit to drill a .8 inch hole for the cable exit,
as shown on the template.
4. Drill anchor holes (optional).
If using the included anchors, use an appropriate drill bit to drill four screw
holes where marked.
5. Remove camera dome cover.
Using a T15 TORX™, loosen the 2 locking screws and remove
dome cover.
6. Secure camera to mounting surface.
Thread the cable through the hole and secure the camera base to the
mounting surface using the included 4 self-tapping screws.
7. Connect 47 series camera to NVR.
Connect the 47 series camera to one of the camera inputs on the NVR.
8. Congure 47 series camera.
Using a laptop, access the camera’s live view as described in the
Configuration section.
9. Adjust camera angle and eld of view.
Use a small Phillips head screwdriver (pan rotation) and a T15 TORX (tilt
rotation) to loosen the screws on the camera gimbal to adjust the camera
angle to the desired field of view. Once completed, tighten the screws in
place.
10. Secure camera dome cover.
Using a T15 TORX™, tighten the 2 locking screws and secure the dome cover
over the camera and base.

7
47 SERIES IP CAMERA
Installation of Network Cable Waterproof Jacket
(Optional)
If the camera is installed outdoors, a waterproof jacket on the connection is
required for water resistance.
1 - Camera’s Network Interface
Socket
2 - O-Type Gasket
3 - Network Plug
4 - Waterproof Endcap
5 - Waterproof Rubber Gasket
6 - Lock Nut
7 - Network Cable from Router/
Switch
Water-proof Jacket Components