Sagem Dr. Neuhaus Tainy GMOD-T1 User manual

File 3159AD001_V1_3_050701.doc
File saved 01.07.2005
File printed 01.07.2005
State Freigabe
Autor Katharina Bora
TAINY
TAINYTAINY
TAINY GMOD
GMODGMOD
GMOD-
---T1 T1T1
T1
Installation Manual

Page 2 of 31 TAINY GMOD-T1
File 3159AD001_V1_3_050701.doc
File saved 01.07.2005
File printed 01.07.2005
State Freigabe
Autor Katharina Bora
!Safety precautions
General: The product TAINY GMOD-T1 complies with European standard EN60950, 05.2003, Safety
of Information Technology Equipment.
Read the installation instructions carefully before using the device.
Keep the device away from children, especially small children.
The device must not be installed or operated outdoors or at damp locations.
Do not operate the device if the connecting leads or the device itself are damaged.
External power supply: Use only an external power supply which also complies with EN60950. The
output voltage of the external power supply must not exceed 30VDC. The output of the external power
supply must be short-circuit proof.
When connecting to a battery or accumulator, make sure that an all-pole circuit-breaker (main battery
switch) with sufficient selectivity and a fuse with sufficient selectivity are provided between the device
and the battery or accumulator.
Please pay regard to section Technical Data of the installation manual, as well as the installation and
utilisation regulations of the respective manufacturers of the power supply, the battery or the
accumulator.
SIM card: To install the SIM card the device must be opened. Before opening the device, disconnect
it from the supply voltage. Static charges can damage the device when it is open. Discharge the
electric static of your body before opening the device. To do so, touch an earthed surface, e.g. the
metal casing of the switch cabinet. Please pay regard to section Inserting or changing the SIM card of
the installation manual.
Handling cables: Never pull a cable connector out of a socket by its cable, but pull on the connector
itself. Cable connectors with screw fasteners (D-Sub) must always be screwed on tightly. Do not lay
the cable over sharp corners and edges without edge protection. If necessary, provide sufficient strain
relief for the cables.
For safety reasons, make sure that the bending radius of the cables is observed.
Failure to observe the bending radius of the antenna cable results in the deterioration of the system's
transmission and reception properties. The minimum bending radius static must not fall below 5 times
the cable diameter and dynamic below 15 times the cable diameter.
Radio device: Never use the device in places where the operation of radio devices is prohibited. The
device contains a radio transmitter which could in certain circumstances impair the functionality of
electronic medical devices such as hearing aids or pacemakers. You can obtain advice from your
physician or the manufacturer of such devices. To prevent data carriers from being demagnetised, do
not keep disks, credit cards or other magnetic data carriers near the device.
Installing antennas: The emission limits as recommended by the Commission on Radiological
Protection (13/14 September 2001) must be observed.
Installing an external antenna: When installing an antenna outdoors it is essential that the antenna
is fitted correctly by a qualified person. Lightning Protection Standard VDE V 0185 Sections 1 to 4, in
its current version, and further standards must be observed.
Lightning protection category for buildings: For outdoor installation, the antenna may be fitted only
within the lightning protection zones O/E or 1. These lightning protection zones are prescribed by the
lightning protection spherical radius.
The EMV lightning protection zone concept is to be observed. To avoid large induction loops a
lightning protection equipotential bonding is to be used. If the antenna or antenna cable is installed
near to the lightning protection system, the minimum distances to the lightning protection system must
be observed. If this is not possible, insulated installation as described in VDE V 0185 Sections 1 to 4,
in its current version, is essential.

TAINY GMOD-T1 Page 3 of 31
File 3159AD001_V1_3_050701.doc
File saved 01.07.2005
File printed 01.07.2005
State Freigabe
Autor Katharina Bora
!Warning !
This is a class A equipment. This equipment can disturb other electric equipment in living areas; in
this case the operator can be demanded to carry out appropriate measures.
Product no. 3159
Doc. no. 3159AD001 Rev. 1.3

Contents
Page 4 of 31 TAINY GMOD-T1
File 3159AD001_V1_3_050701.doc
File saved 01.07.2005
File printed 01.07.2005
State Freigabe
Autor Katharina Bora
Contents
1Introduction......................................................................................................... 5
1.1 Operating condition: GPRS subscriber contract................................ 5
To be able to use the TAINY GMOD-T1 ... ....................................... 5
2Putting the device into operation...................................................................... 6
Connections and LEDs .................................................................... 6
2.1 Inserting or changing the SIM card ................................................... 7
2.2 Connecting the device .................................................................... 11
2.3 Switching the device on/off ............................................................. 12
Switching on.................................................................................... 12
Switching off the GSM engine (Recommended) ............................. 12
Switching off… ................................................................................ 12
2.4 Installing the modem driver under Windows ................................... 13
2.5 Setting up the dial-up connection (under Windows)........................ 17
Purpose of the dial-up connection................................................... 17
Set up the dial-up connection.......................................................... 17
3Operation........................................................................................................... 23
Controlling with applications............................................................ 23
Controlling direct with AT commands.............................................. 23
Enter PIN first.................................................................................. 23
3.1 Setting the PIN and APN ................................................................ 24
Enter PIN ........................................................................................ 24
Set APN .......................................................................................... 24
3.2 Establishing and closing GPRS or Internet connections ................. 25
Making the connection .................................................................... 25
Closing the connection.................................................................... 25
4Entering AT commands ................................................................................... 26
Enter PIN first.................................................................................. 26
Working with a terminal program .................................................... 26
4.1 The AT command language............................................................ 27
Syntax............................................................................................. 27
4.2 Some AT commands ...................................................................... 28
5Technical Data .................................................................................................. 29

Introduction
TAINY GMOD-T1 Seite 5 von 31
File 3159AD001_V1_3_050701.doc
File saved 01.07.2005
File printed 01.07.2005
State Freigabe
Autor Katharina Bora
1 Introduction
The TAINY GMOD-T1 serves the following purpose:
• GPRS modem
• GSM data modem
• GSM fax modem
• SMS adapter
The device establishes data connections by radio via a GSM
network
• IP connections via the GPRS (General Packet Radio
Service) of a GSM network (Global System for Mobile
Communication = mobile radio network).
• Modem connections by CSD (Circuit Switched Data)
• Fax connections
• Sending and receiving SMS (Short Message Service)
1.1 Operating condition: GPRS subscriber contract
To be able to use the
TAINY GMOD-T1 ...
Use of the TAINY GMOD-T1 requires:
• a subscriber contract with a GSM network operator (e.g.
TD1, Vodafone, E-Plus, O2) that supports GPRS
• release of the GPRS service for the user in question by the
network operator

Putting the device into operation
Page 6 of 31 TAINY GMOD-T1
File 3159AD001_V1_3_050701.doc
File saved 01.07.2005
File printed 01.07.2005
State Freigabe
Autor Katharina Bora
2 Putting the device into operation
To put the device into operation, perform the following steps in the order given:
Page
1. Inserting or changing the SIM card 7
2. Connecting the device
11
3. Installing the modem driver under Windows 13
4. Setting up the dial-up connection (under Windows) 17
Connections and
LEDs
LED Status Meaning
On permanently Operating voltage on
P (Power)
Off No operating voltage
On permanently GSM connection active (DCD on)
C (Connect)
Off No GSM connection
Blinking regularly Device booked into GSM network
Flickering Data exchange at COM port
S (Status)
Off Device not booked into GSM network
LEDs: P (Power)
C (Connect)
S (Status)
Antenna
COM (RS232)
for connecting the application
Connectors for supply voltage
24 V DC voltage
0V
SW
+24V
+24V

Putting the device into operation
TAINY GMOD-T1 Seite 7 von 31
File 3159AD001_V1_3_050701.doc
File saved 01.07.2005
File printed 01.07.2005
State Freigabe
Autor Katharina Bora
2.1 Inserting or changing the SIM card
The device must be switched off when you insert or change the SIM card.
A plug-in SIM card (3 V) is used.
1. Make sure that the device is disconnected from the supply voltage.
2. The TAINY GMOD-T1 must be
opened to insert the SIM card.
The housing is fastened by two
clamps, one on top of the housing and
one on the bottom side.
3. With a suitable object press one of the
clamps cautiously (see picture) so that
the catch opens.
4. Remove the rear section of the
housing.
Clamp
Clamp

Putting the device into operation
Page 8 of 31 TAINY GMOD-T1
File 3159AD001_V1_3_050701.doc
File saved 01.07.2005
File printed 01.07.2005
State Freigabe
Autor Katharina Bora
5. The SIM card holder is visible on the
motherboard.
6. With a suitable object open the flap of
the SIM card holder by moving it
cautiously about 2 mm to the left - in
the direction of the arrow (see red
arrow in the illustration) so that it can
be raised.
7. Raise the flap of the SIM card holder
so that you can insert the SIM card.
In the illustration below, the
compartment into which you can insert
the SIM card is emphasized in white.
SIM card holder

Putting the device into operation
TAINY GMOD-T1 Seite 9 von 31
File 3159AD001_V1_3_050701.doc
File saved 01.07.2005
File printed 01.07.2005
State Freigabe
Autor Katharina Bora
8. Slide the SIM card into the flap of the
SIM card holder, with the gold-
coloured microchip pointing down. The
flap has a groove for this purpose. The
notched corner of the SIM card has to
point towards the front of the device
(see illustration).
9. Slide the SIM card down into the flap
as far as possible.
10. Lower the flap paying attention to the
notched corner of the SIM card (see
illustration).

Putting the device into operation
Page 10 of 31 TAINY GMOD-T1
File 3159AD001_V1_3_050701.doc
File saved 01.07.2005
File printed 01.07.2005
State Freigabe
Autor Katharina Bora
11. With your fingernail or a suitable object
move the flap about 2 mm to the right
(in the direction of the arrow) until you
can feel it click into place.
12. Now the SIM card holder is locked into
position.
13. Finally re-attach both housing parts:
Slide the motherboard into the rails on
top and bottom inside the rear section
of the housing. Close the housing by
slightly pressing both housing parts
together so that the clamps on the
upper and lower part of the housing
engage.
The housing is locked when both
clamps have clicked shut.
Rail

Putting the device into operation
TAINY GMOD-T1 Seite 11 von 31
File 3159AD001_V1_3_050701.doc
File saved 01.07.2005
File printed 01.07.2005
State Freigabe
Autor Katharina Bora
2.2 Connecting the device
Antenna The antenna connector – SMA socket - is situated on the upper
part of the front.
Impedance recommended: ca. 50 Ohm
Connectors for
current supply
The screw terminals on the top of the device are for connecting the
current supply:
24 V DC voltage (nominal), Ityp. 220mA@24V. (Please also refer to
chapter Technical Data, page 29.)
+ 24 V
+ 24 V
SW (12-30VDC)
0 V
Both screw terminals to the left (24 V)
are internally connected.
Switch input SW: If unused, the two
middle screw terminals (+24V and
SW) have to be bridge-connected.
Serial port V.24/V.28 to connect a data
terminal, e.g. a PC.
The RS-232 connecting cable must not exceed
a length of 15m.
Pin assignment:
1DCD 6 DSR
2RXD 7 RTS
3TXD 8 CTS
4DTR 9 RI
Serial interface
COM
5SGND

Putting the device into operation
Page 12 of 31 TAINY GMOD-T1
File 3159AD001_V1_3_050701.doc
File saved 01.07.2005
File printed 01.07.2005
State Freigabe
Autor Katharina Bora
2.3 Switching the device on/off
Make sure that the TAINY GMOD-T1 is connected correctly (see chapters Connecting
the device and Technical Data).
Switching on... The devices switches on as soon as the operating voltage is
supplied and the switch input (SW) is active.
Switching off the
GSM engine
(Recommended)
Switch off the GSM module with the AT command AT+CPOF
before disconnecting the device from the supply voltage. This is the
only way to ensure that it logs off correctly from the GSM network.
Switching off… The device switches off when disconnected from the supply
voltage.

Putting the device into operation
TAINY GMOD-T1 Seite 13 von 31
File 3159AD001_V1_3_050701.doc
File saved 01.07.2005
File printed 01.07.2005
State Freigabe
Autor Katharina Bora
2.4 Installing the modem driver under Windows
If the device is operated with a computer running under Windows we recommend that the
supplied modem driver is installed.
The following instructions show dialogue boxes that are displayed
during installation under Windows XP. If you are using a different
Windows version (Windows 2000), proceed accordingly.
Under Windows 2000 or Windows XP you must be registered as
the administrator. In addition please make sure that no other
modem drivers are or will be installed for the respective interface.
Follow the instructions below and those on your screen:
1. Insert the supplied CD in the CD-ROM drive.
If an action is started automatically, interrupt it.
2.
Click on Start, Control Panel.
Consequence:
The Control Panel dialogue box is displayed. Where required,
Switch to classic view.
Double-click on Phone and Modem Options.
3.
Consequence: The Phone and Modem Options dialogue box is
displayed.
On the Modems tab, click on Add....
4.
The Add New Hardware Wizard for the installation of a new
modem appears.
Example:
1 modem driver
is installed

Putting the device into operation
Page 14 of 31 TAINY GMOD-T1
File 3159AD001_V1_3_050701.doc
File saved 01.07.2005
File printed 01.07.2005
State Freigabe
Autor Katharina Bora
When this dialogue box is displayed...
Select Don't detect my modem; I will select it from a list.
Then click on Next >.
5.
Click on Have Disk.....
Click on Have
Disk....
Select Don't
detect my
modem; I will
select it from a
list.

Putting the device into operation
TAINY GMOD-T1 Seite 15 von 31
File 3159AD001_V1_3_050701.doc
File saved 01.07.2005
File printed 01.07.2005
State Freigabe
Autor Katharina Bora
6. In the next dialogue box, change to the inserted CD-ROM and
then to the Driver folder.
Select: TAINY_MOD_T1.INF
Follow the instructions on the screen.
Click on Next >.
7. Next you are asked to select a COM port.
Select the COM port of the computer to which the device is
connected.
Then click on Next >.
8. When this dialogue box is displayed...
Click on Continue Anyway.

Putting the device into operation
Page 16 of 31 TAINY GMOD-T1
File 3159AD001_V1_3_050701.doc
File saved 01.07.2005
File printed 01.07.2005
State Freigabe
Autor Katharina Bora
9.
Click on Finish.
10. When installation is completed the installed modem driver will
be listed in the Phone and Modem Options dialogue box.
Click on OK to close the window.

Putting the device into operation
TAINY GMOD-T1 Seite 17 von 31
File 3159AD001_V1_3_050701.doc
File saved 01.07.2005
File printed 01.07.2005
State Freigabe
Autor Katharina Bora
2.5 Setting up the dial-up connection (under Windows)
Purpose of the
dial-up
connection
Not necessary for:
In order to be able to establish a GPRS connection using the PPP
(Point to Point) Protocol you must set up a dial-up connection
under Windows.
The PPP Protocol is used, for example, for dial-up connections to
the Internet or to a private network which uses the IP Control
Protocol (IPCP). It facilitates the transport of IP data packets via a
PPP connection.
It is not necessary to set up a dial-up connection for
• data transfer, e.g. by terminal program
• fax transmissions
• SMS (Short Message Service)
Set up the dial-up
connection
The following instructions show dialogue boxes that are displayed
when setting up a dial-up connection under Windows XP. If you are
using a different Windows version (Windows 2000), proceed
accordingly.
Under Windows 2000 or Windows XP you must be registered as
the administrator.
Requirements:
You have installed the modem driver (see page 13)
Follow the instructions below and those on your screen:
1.
Click on Start, Control Panel.
Consequence:
The Control Panel dialogue box is displayed.
Where required, Switch to classic view.
Double-click on Network Connections.
Consequence:
The Network Connections dialogue box appears.
Click on Make New Connection.

Putting the device into operation
Page 18 of 31 TAINY GMOD-T1
File 3159AD001_V1_3_050701.doc
File saved 01.07.2005
File printed 01.07.2005
State Freigabe
Autor Katharina Bora
2.
The New Connection Wizard is launched.
Click on Next >.
3.
Select Connect to the Internet and click on Next >.
Select Connect to
the Internet.

Putting the device into operation
TAINY GMOD-T1 Seite 19 von 31
File 3159AD001_V1_3_050701.doc
File saved 01.07.2005
File printed 01.07.2005
State Freigabe
Autor Katharina Bora
4.
Select Set up my connection manually and click on Next >.
5.
Select Connect using a dial-up modem and click on Next >.
6. When you are asked to choose a modem, select:
Dr. Neuhaus TAINY GMOD-T1
Select Set up my
connection
manually
Select Connect
using a dial-up
modem

Putting the device into operation
Page 20 of 31 TAINY GMOD-T1
File 3159AD001_V1_3_050701.doc
File saved 01.07.2005
File printed 01.07.2005
State Freigabe
Autor Katharina Bora
7.
Give the dial-up connection (service) a name that describes
your purpose. Then click on Next >.
8.
Type the phone number for access to the Internet: *99***1#
Then click on Next >.
In the corresponding dialogue box under Windows 2000,
deactivate the option Enter Your Area Code and Local
Access Number!
*99***1#