Samsung RFD01F series User manual

Radio Access Network
RFD01F Series
Installation Manual
Describes product installation and requirement procedure.
Document Version 1.0
January 2017
Document Number: -

© 2017 SAMSUNG Electronics Co., Ltd.
All Rights Reserved. No part of this document may be photocopied, reproduced, stored in a retrieval
system, or transmitted, in any form or by any means whether, electronic, mechanical, or otherwise
without the prior written permission of SAMSUNG Electronics Co., Ltd.
No warranty of accuracy is given concerning the contents of the information contained in this
publication. To the extent permitted by law no liability (including liability to any person by reason of
negligence) will be accepted by SAMSUNG Electronics Co., Ltd., its subsidiaries or employees for
any direct or indirect loss or damage caused by omissions from or inaccuracies in this document.
SAMSUNG Electronics Co., Ltd. reserves the right to change details in this publication without notice.
SNMTC-v3-0312
This manual should be read and used as a guideline for properly installing and/or operating the
product. Owing to product variations across the range, any illustrations and photographs used in
this manual may not be a wholly accurate depiction of the actual products you are using.
This manual may be changed for system improvement, standardization and other technical
reasons without prior notice.
Samsung Networks documentation is available at http://www.samsungdocs.com

RFD01F Series Installation Manual v1.0 iii
© Samsung Proprietary and Confidential
Contents
Preface viii
Relevance ......................................................................오류! 책갈피가 정의되어 있지 않습니다.
Conventions in this Document .......................................................................................................viii
New and Changed Information ....................................................................................................... ix
Revision History............................................................................................................................... ix
Organization of This Document ...................................................................................................... ix
Personal and Product Safety ........................................................................................................... ix
Chapter 1 Before Installation 1
System Configuration and Interface ................................................................................................ 1
RRU Configuration ....................................................................................................................... 1
RRU Interface............................................................................................................................... 2
Specifications ................................................................................................................................... 3
Cautions for Installation ................................................................................................................... 3
Before Installing........................................................................................................................... 4
While Installing ............................................................................................................................ 4
After Installing ............................................................................................................................. 5
Installation Tools .............................................................................................................................. 5
Chapter 2 Installing System 9
Installation Procedure ...................................................................................................................... 9
System Arrangement ..................................................................................................................... 10
Unpacking and Transporting .......................................................................................................... 12
Bringing in Items........................................................................................................................ 12
Unpacking Items ........................................................................................................................ 12
RRU Handling ................................................................................................................................. 13
Fixing RRU ...................................................................................................................................... 14
Fixing Unit Bracket..................................................................................................................... 14
Fixing Pole Type ......................................................................................................................... 17
Fixing Wall Type......................................................................................................................... 28
Chapter 3 Connecting Cables 38
Cabling Procedure .......................................................................................................................... 38
Guidelines for Cable Connections .................................................................................................. 39
Cable Path Inspection ................................................................................................................ 39
Cable Cutting ............................................................................................................................. 40
Cable Installation ....................................................................................................................... 40
Cable Binding ............................................................................................................................. 41
Connector Attachment............................................................................................................... 41
Identification Tag Attachment................................................................................................... 42
Cabling Diagram ............................................................................................................................. 43
Grounding ...................................................................................................................................... 45
Ground Cable Connection .......................................................................................................... 46
Power Cabling ................................................................................................................................ 48
Power Cable Connection ............................................................................................................ 49
Interface Cable Connection............................................................................................................ 59
Remove/Insert Optic Module ................................................................................................. 59

Contents
RFD01F Series Installation Manual v1.0 iv
© Samsung Proprietary and Confidential
Optic Cable Connection ............................................................................................................ 60
RET Cable Connection ................................................................................................................ 71
RF Cable Connection .................................................................................................................. 75
Chapter 4 Inspect the Installation 86
Appendix A Acronyms 91
Appendix B Clean the Optical Connectors 92
Introduction ................................................................................................................................... 92
Measure the Optical Output and Connecting the Optical Connector ........................................ 93
Appendix C Standard Torque 94

RFD01F Series Installation Manual v1.0 v
© Samsung Proprietary and Confidential
List of Figures
Figure 1. RRU Configuration............................................................................................................................ 1
Figure 2. RRU Interface ................................................................................................................................... 2
Figure 3. Procedure to Install the RRU............................................................................................................ 9
Figure 4. RRU_Wall Type Standard Installation ............................................................................................ 10
Figure 5. RRU Arrangement_Pole Type Installation...................................................................................... 11
Figure 6. Using a Handle to transport an RRU .............................................................................................. 13
Figure 7. Unit Bracket Fixing Type................................................................................................................. 14
Figure 8. Unit Bracket Fixing (Standard Installation) ................................................................................. 15
Figure 9. Unit Bracket Fixing (Side Installation) ......................................................................................... 16
Figure 10. Assembling the Mounting Bracket_Pole Type(1)........................................................................... 17
Figure 11. Assembling the Mounting Bracket_Pole Type(2)........................................................................... 18
Figure 12. Lifting RRU & Pole Mounting Bracket Assembly_Pole Type(1) ...................................................... 19
Figure 13. Lifting RRU/Pole Mounting Bracket Assembly_Pole Type(2) ......................................................... 20
Figure 14. Assembling the Mounting Bracket Assembly_Pole Type(1)........................................................... 21
Figure 15. Assembling the Mounting Bracket Assembly_Pole Type(2)........................................................... 22
Figure 16. Leveling Pole Mounting Bracket Assembly .................................................................................... 23
Figure 17. RRU Fixging_Pole Type (Standard Installation) .............................................................................. 24
Figure 18. RRU Fixing_Pole Type (Standard Installation) ................................................................................ 25
Figure 19. RRU Fixing_Pole Type (Side Installation)........................................................................................ 26
Figure 20. RRU Fixing_Pole Type (Side Installation)........................................................................................ 27
Figure 21. RRU dimensions for Wall Type (Standard Installation) .................................................................. 29
Figure 22. RRU dimensions for Wall Type (Side Installation_ ......................................................................... 29
Figure 23. Example of Marking_Use the Mounting bracket ........................................................................... 30
Figure 24. Drilling & Anchoring Example ........................................................................................................ 31
Figure 25. Fixing Mounting Bracket on a Wall ............................................................................................... 32
Figure 26. RRU Fixing_Wall Type Standard Installation(1).............................................................................. 34
Figure 27. RRU Fixing_Wall Type Standard Installation(2).............................................................................. 35
Figure 28. RRU Fixing_Wall Type Side Installation(1) ..................................................................................... 36
Figure 29. RRU Fixing_Wall Type Side Installation(2) ..................................................................................... 37
Figure 30. Procedure to Connect System Cable.............................................................................................. 38
Figure 31. Cable Connection Procedure.......................................................................................................... 39
Figure 32. Cable Diagram ................................................................................................................................ 43
Figure 33. Ground Cable Connection (1)......................................................................................................... 47
Figure 34. Ground Cable Connection (2)......................................................................................................... 47
Figure 35. Power Equipment Elements........................................................................................................... 48
Figure 36. Power Connector Assembly (1) ...................................................................................................... 50
Figure 37. Power Connector Assembly (2) ...................................................................................................... 50
Figure 38. Power Connector Assembly (3) ...................................................................................................... 51
Figure 39. Power Connector Assembly (4) ...................................................................................................... 51
Figure 40. Power Connector Assembly (5) ...................................................................................................... 52
Figure 41. Power Connector Assembly (6) ...................................................................................................... 52
Figure 42. Power Connector Assembly (7) ...................................................................................................... 53
Figure 43. Power Connector Assembly (8) ...................................................................................................... 54
Figure 44. Power Connector Assembly (9) ...................................................................................................... 55
Figure 45. Power Connector Assembly (10) .................................................................................................... 55
Figure 46. Hybrid(Power) Cable Connection (1) ............................................................................................. 57

List of Figures
RFD01F Series Installation Manual v1.0 vi
© Samsung Proprietary and Confidential
Figure 47. Hybrid(Power) Cable Connection (2) ............................................................................................. 58
Figure 48. Optic Module Removal (1) ............................................................................................................. 59
Figure 49. Optic Module Removal (2) ............................................................................................................. 59
Figure 50. Optic Module Removal (3) ............................................................................................................. 59
Figure 51. Optic Module Inset......................................................................................................................... 60
Figure 52. Optic Cable Adapter Assembly (1) ................................................................................................. 62
Figure 53. Optic Cable Adapter Assembly (2) ................................................................................................. 62
Figure 54. Optic Cable Adapter Assembly (3) ................................................................................................. 63
Figure 55. Optic Cable Adapter Assembly (4) ................................................................................................. 63
Figure 56. Optic Cable Adapter Assembly (5) ................................................................................................. 64
Figure 57. Optic Cable Adapter Assembly (6) ................................................................................................. 65
Figure 58. Optic Cable Adapter Assembly (7) ................................................................................................. 65
Figure 59. Optic Cable Adapter Assembly (8) ................................................................................................. 66
Figure 60. Optic Cable Adapter Assembly (9) ................................................................................................. 66
Figure 61. Optic Cable Adapter Assembly (10) ............................................................................................... 67
Figure 62. Optic Cable Adapter Assembly (11) ............................................................................................... 67
Figure 63. Optic cable connection (1) ............................................................................................................. 68
Figure 64. Optic cable connection (2) ............................................................................................................. 69
Figure 65. Optic cable connection (3) ............................................................................................................. 69
Figure 66. Optic cable connection (4) ............................................................................................................. 70
Figure 67. RET Cable Connection (1) ............................................................................................................... 72
Figure 68. RET Cable Connection (2) ............................................................................................................... 73
Figure 69. RET Cable Connection (3) ............................................................................................................... 74
Figure 70. RF Cable Connection using JMA Boots (1)...................................................................................... 76
Figure 71. RF Cable Connection using JMA Boots (2)...................................................................................... 77
Figure 72. RF Cable Connection using JMA Boots (3)...................................................................................... 78
Figure 73. RF Cable Connection using a Cold Shrink Tube (1)......................................................................... 80
Figure 74. RF Cable Connection using a Cold Shrink Tube (2)......................................................................... 80
Figure 75. RF Cable Connection using a Cold Shrink Tube (3)......................................................................... 81
Figure 76. RF Cable Connection using a Cold Shrink Tube (4)......................................................................... 82
Figure 77. RF Cable Connection using a Cold Shrink Tube (5)......................................................................... 83
Figure 78. Installation Inspection Procedure .................................................................................................. 86

List of Tables
RFD01F Series Installation Manual v1.0 vii
© Samsung Proprietary and Confidential
List of Tables
Table 1. Specifications ................................................................................................................................... 3
Table 2. Basic Installation Tools..................................................................................................................... 5
Table 3. Parts a Tools for fixing Unit Bracket (Standard Installation)....................................................... 15
Table 4. Parts a Tools for fixing Unit Bracket (Side Installation) .............................................................. 16
Table 5. Parts a Tools for fixing Pole Mounting Bracket .............................................................................. 17
Table 6. Parts a Tools for fixing Pole Mounting Bracket Assembly_Pole Type ............................................ 21
Table 7. Leveling Using a Level .................................................................................................................... 22
Table 8. Parts a Tools for fixing RRU_Pole Type (Standard Installation)...................................................... 24
Table 9. Parts a Tools for fixing RRU_Pole Type (Side Installation) ............................................................. 26
Table 10. Tools for Marking ........................................................................................................................... 28
Table 11. Parts and Tools for Drilling & Fixing Anchor................................................................................... 31
Table 12. Anchor Bolt Drill Bits and Hole Depth ............................................................................................ 31
Table 13. Parts and Tools for Fixing Bracket Assembly.................................................................................. 32
Table 14. Parts a Tools for fixing RRU_Wall Type Standard Installation........................................................ 34
Table 15. Parts and Tools for Fixing RRU 1Sector Standard_Wall Type......................................................... 36
Table 16. Recommended Minimum Allowed Cable bend Radius .................................................................. 41
Table 17. RRU Connection Cable ................................................................................................................... 44
Table 18. Parts and Tools for Grounding ....................................................................................................... 46
Table 19. Parts and Tools for Power Connector Assembly ............................................................................ 49
Table 20. Parts and Tools for Power Cable Connection................................................................................. 56
Table 21. Power Cable/Connector Pin Map................................................................................................... 56
Table 22. Parts and Tools for Optic Cable Adapter Assembly........................................................................ 60
Table 23. Parts for RET Cable Connection...................................................................................................... 71
Table 24. RET Cable Pin Map ......................................................................................................................... 71
Table 25. RF Cable Minimum Radius of Curvature ........................................................................................ 75
Table 26. Parts and Tools for connecting RF cable ........................................................................................ 76
Table 27. Parts and Tools for connecting RF cable ........................................................................................ 79
Table 28. RF Cable Identification Tag............................................................................................................. 84
Table 29. Construction Situation Check list ................................................................................................... 87
Table 30. Standard Torque Value for Fastening Bolts ................................................................................... 94
Table 31. Brass Bolts Torque Value................................................................................................................ 94
Table 32. Connector Connection Torque Value ............................................................................................. 94

RFD01F Series Installation Manual v1.0 viii
© Samsung Proprietary and Confidential
Preface
This manual describes how to install the 850MHz RRU including how to connect
cables. This manual includes the following 850MHz RRU(SLS-BR03U):
Conventions in this Document
Samsung Networks product documentation uses the following conventions.
Symbols
Symbol
Description
Indicates a task.
Indicates a shortcut or an alternative method.
Provides additional information.
Provides information or instructions that you should follow to avoid service
failure or damage to equipment.
Provides information or instructions that you should follow to avoid personal
injury or fatality.
Provides antistatic precautions that you should observe.
Menu Commands
menu | command
This indicates that you must select a command on a menu, where menu is the
name of the menu, and command is the name of the command on that menu.
File Names and Paths
These are indicated by a bold typeface. For example:
Copy filename.ext into the /home/folder1/folder2/bin/ folder.
User Input and Console Screen Output Text
Input and output text is presented in the Courier font. For example,
context <designated epc-context-name>
CLI commands are presented in bold small caps. For example,
Type the RTRV-NE-STS command in the input field.

Preface
RFD01F Series Installation Manual v1.0 ix
© Samsung Proprietary and Confidential
New and Changed Information
This section describes information that has been changed since the previous
publication of this manual.
The product name was corrected.
Revision History
The following table lists all versions of this document.
Document Number
Product/Software
Version
Document Version
Publication Date
Remarks
-
RFD01F Series
1.0
January 2017
-
Organization of This Document
Section
Title
Description
Chapter 1
Before Installation
This chapter introduces RRU and describes items should be
understood before installation.
Chapter 2
Installing System
This chapter describes the procedures to install the RRU.
Chapter 3
Connecting Cables
This chapter describes the procedures to connect the cables
to the RRU installed.
Chapter 4
Inspect the Installation
This chapter describes the procedures of inspecting
installation status after RRU installation and cabling is
completed.
Appendix A
Acronyms
This annex describes the acronyms used in this manual.
Appendix B
Clean the Optical
Connectors
This annex describes the procedure of cleaning the optical
connector and cleaning tool.
Appendix C
Standard Torque
This annex describes the standard torque when fastening the
bolt.
Personal and Product Safety
This product safety information includes European directives, which you must
follow. If these do not apply in your country, please follow similar directives that
do apply in your country.
Electrical
All structural parts are grounded and all input and outputs have built-in isolation
from the network. All input and output ports that connect to external power
sources are designed to meet relevant national safety requirements.

Preface
RFD01F Series Installation Manual v1.0 x
© Samsung Proprietary and Confidential
The product contains hazardous energy levels as defined by UL 60950. Care must
be taken when maintaining this equipment as injury to personnel or damage to the
equipment could result from mistakes. Maintenance should only be carried out by
trained and competent engineers who are familiar with the relevant procedures and
instructions.
Lasers
The product is fitted with optic modules rated as Class 1 radiation-emitting devices
under IEC 60825-1.
Manual Handling
Care should be taken when handling equipment. Give due consideration to the
weight of the equipment, the physical capability of the individual(s) handling the
equipment, and movements such as twisting, bending and stooping, which could
lead to skeletal and muscular injuries.
Installation
Installation must be carried out by trained and competent engineers only. All
relevant safety measures must be taken to ensure equipment is not connected to
live power and transmission sources during installation. Equipment must be
correctly installed in order to meet the relevant safety standards and approval
conditions.
The cable between the power distribution point and the installed equipment must
have a cross-sectional area of 1.5 mm2.
Maintenance
Maintenance must only be carried out by a suitably trained and competent
technician. All safety instructions must be carefully observed at all times.
Equipment covers should not be removed while live power and transmission is
connected unless in a controlled environment by trained technicians.
Environment
The product must be operated in an environment within the specified relative
humidity and ambient temperature ranges.
Grounding
To comply with UL 60950, the equipment must be connected to a safety
grounding point via a permanent connection. Grounding points are located on the
product for this purpose. Always connect the ground cable before fitting other
cables. The product must remain grounded continuously unless all connections to
the power supply and data network are all removed.

Preface
RFD01F Series Installation Manual v1.0 xi
© Samsung Proprietary and Confidential
If equipment is grounded through a cabinet or rack, make sure it is done so
properly according to the installation instructions.
Chemical Warning
This product contains chemicals known to the State of California to cause cancer
and reproductive toxicity.
California USA Only
This Perchlorate warning applies only to primary CR (Manganese Dioxide)
Lithium coin cells in the product sold or distributed ONLY in California USA
‘Perchlorate Material-special handling may apply, See
www.dtsc.ca.gov/hazardouswaste/perchlorate.’

RFD01F Series Installation Manual v1.0 1
© Samsung Proprietary and Confidential
Chapter 1 Before
Installation
System Configuration and Interface
RRU Configuration
The configuration of RRU is as follows:
Figure 1. RRU Configuration
[Bottom View]
12.59 (320)
[Front View]
[Top View]
[Left View]
[Right View]
[Rear View]
15.09 (383)
7.68 (195)
12.59 (320)
Unit: in.(mm)

Chapter 1 Before Installation
RFD01F Series Installation Manual v1.0 2
© Samsung Proprietary and Confidential
RRU Interface
The interface structure of RRU is as follows:
Figure 2. RRU Interface
ANT0
L1 (CPRI_1)
L0 (CPRI_0)
DC_PWR
[Bottom View]
Ground Terminal
RET
ANT1
ANT2
ANT3

Chapter 1 Before Installation
RFD01F Series Installation Manual v1.0 3
© Samsung Proprietary and Confidential
Specifications
The table below lists the main specifications of the RFD01F-26A.
Table 1. Specifications
Item
RRU
Air technology
FDD LTE
Operating Frequency
DL: 862~869MHz (7 MHz)
UL: 817~824 MHz(7MHz)
Channel Bandwidth
1.23 MHz(CDMA), 3/5 MHz (LTE, Scalable BW)
RF Power per sector
40 W ×2 T
CDU-RU interface
CPRI (2.5 Gbps optic 2 ports, 20 km)
Input Voltage
-48 V DC (-38 ~ -57V DC)
Dimension (in./mm)
12.60/320(W) × 7.68/195(D) ×12.60/320(H)
Weight
Under 22 kg
Operating Temperature
(Ambient)
-40°C ~ 55°C
Operating Humidity
5~100 %RH.
Ingress Protection
Rating
IP65
Salt Fog / Salt Spray
Telcordia GR-487-CORE, Section 3.38.1
Seismic Specification
Telcordia GR-63-CORE,
Earthquake (Zone 4) (Section 4.4.1)
Office Vibration (Section 4.4.4)
Transportation Vibration (Section 4.4.5)
Wind Resistance
Telcordia GR-487-CORE, Section 3.34
EMC
FCC Title 47 CFR Part 15
Surge Protection
DC : ± 20kA (Line to Line, Line to PE)
RET : ± 3kA (All core to PE)
ANT : ± 20kA (Core to PE)
ESD
Contact Discharge : ± 8kV
Air Discharge : ± 15kV
Safety
UL 60950-1 2nd Ed.
RF
FCC Title 47 CFR Part 90
Health
OET Bulletin 65
Cautions for Installation
Observe the following safety instructions when installing the system:
Installation shall be in accordance with the applicable local electric codes.
The equipment shall be located in restricted access locations.

Chapter 1 Before Installation
RFD01F Series Installation Manual v1.0 4
© Samsung Proprietary and Confidential
Before Installing
Post warning signs in areas where high-voltage cables are installed.
Post ‘off limit’ signs in areas where accidents are most expected.
With guardrails or fences, block open areas such as connecting parts, roof, and
scaffold.
While Installing
The system power must be cut off before installing.
Be careful not to damage or scratch the boards mounted on the system and the
cables among the boards when the system is transported or installed.
Make sure the power switch of power supply is off when installing the system.
Installing the system with power switch on may cause system damage or fatal
human injury when cables are not correctly connected.
Make sure that worker wears protection gloves and goggles to prevent damage
from debris while drilling holes in a wall or ceiling.
Do not wear accessories such as watches and rings in order to prevent electrical
shock.
Never allow foreign substances to be inserted into unused ports by covering them
with a waterproof cap.
To prevent foreign substances, outdoor air and moisture from entering the cable inlet
(including cable gland and conduit), finish it as follows:
- Unused inlet
Use the hole finishing materials including dust cap and rubber packing.
- Cable-installed inlet
After cable installation, block any space in the inlet with tape, compressed
sponge, rubber packing, and silicon.

Chapter 1 Before Installation
RFD01F Series Installation Manual v1.0 5
© Samsung Proprietary and Confidential
After Installing
Remove any debris produced during the work and clean up the installation site.
In the system, the laser beam light runs through the optical cable. Handle the
optical cables with care as the laser beam can seriously damage the worker’s eyes.
Make sure that worker does not damage installed cables while cleaning the system.
While cleaning the power supply device, take caution that the device does not come
in contact with foreign objects that may cause power failure.
Installation Tools
The basic tools for installation are listed in the table below. The additional tools
required for each site need to be identified and prepared during a site survey before
starting installation.
Table 2. Basic Installation Tools
No.
Name
Specification
Purpose of use
1
Torque Driver
Apply a torque range
: 10~50 lbf.in.
For fastening M6 Screw fixing
2
Screw Driver Bit
'+', No. 1
For fastening Power Connector
'+', No. 3
For fastening M6 Screw fixing
3
Screw Driver
'+', No. 1
For fastening Power Connector
'+', No. 3
For fastening M6 Screw fixing
4
Torque Wrench
Apply a torque range
: 10~50 lbf.in.(30~150 kgf·cm)
For fastening M6 Hex. Bolt
Apply a torque range
: 100~400 lbf·in (100~500 kgf·cm)
For fastening M10 Hex. Bolt/Nut
For fastening DIN Type
Connector
5
Adjustable Torque Wrench
Apply a torque range
: 10~50 lbf.in.(30~150 kgf·cm)
For fastening Optic Cable
Adapter
6
Torque Wrench Spanner Head
Hexagon Head: 0.39 in.(10 mm)
For fastening M6 Hex. Bolt

Chapter 1 Before Installation
RFD01F Series Installation Manual v1.0 6
© Samsung Proprietary and Confidential
No.
Name
Specification
Purpose of use
(for 30~150 kgf·cm)
Hexagon Head: 0.66 in.(17 mm)
(for 100~500 kgf·cm)
For fastening M10 Hex. Bolt/Nut
Hexagon Head: 1.25 in.(32 mm)
(for 100~500 kgf·cm)
For fastening DIN Type
Connector
7
Adjustable Spanner
Hexagon Head: 2.04 in.(52mm)
For fastening Optic Cable
Adapter
8
Spanner
0.39 in.(10 mm), 0.66 in. (17
mm), 1.25 in.(32 mm)
For fastening Hex. Bolt
For fastening DIN Type
Connector
9
Tape Measure
16.40ft/ 164.04ft (5 m/50 m)
Tape measure for length
measurement
10
Level
Normal
For horizontality and verticality
11
Power Extension Cable
30 m
For Power Extension
12
Hammer Drill
Normal
Wall Type Drilling
13
Optic Connector Cleaner
For LC Connector
For Optic Connector Cleaning
14
LAN Tool
Basic Tool
RJ45 Crimper
15
Concrete Drill Bit
0.55 in.(14 mm)
For M10 Set Anchor Bolt
16
Anchor Punch
M10
For M10 Set Anchor Bolt
17
Hammer
Normal
Anchor fixing
18
Vacuum Cleaner
Normal
For removing dust during the
drilling work

Chapter 1 Before Installation
RFD01F Series Installation Manual v1.0 7
© Samsung Proprietary and Confidential
No.
Name
Specification
Purpose of use
19
Cable Cutter
0.23~1.25 in.(6~32 mm)
Cable cutting
20
Crimping Tool
1.5~16 mm2
Pressure terminal for crimping
21
Ratchet Wrench
10 ×13/17 ×19(4 in 1)
For fastening Hex. Bolt
22
Cable Stripper
Apply cable thickness: 0.15~0.62
in. (4~16 mm)
Cable sheath for removal
23
Nipper
Basic Tool
For cutting cable & cable tie
24
Industrial Scissor
Normal
Cutting
25
Knife
Normal
Cutting
26
Heating Gun
50~300°C
Shrinking Heat Shrink Tube
27
Multi tester
Digital Pocket Tester
The voltage and current
measurements
Whether measured cable
disconnection
28
Angle Meter
Normal
Antenna angle measurement
29
Multi master(VSWR & RF
Power)
Normal
Feeder VSWR measurement
30
Fiber Optic Test Set
Wave length:
1270 nm, 1310 nm, 1550
Optical level check

Chapter 1 Before Installation
RFD01F Series Installation Manual v1.0 8
© Samsung Proprietary and Confidential
No.
Name
Specification
Purpose of use
nm(single mode)
850 nm, 1310 nm(multi mode)
32
Jig Tool
Normal
Separate the Optical Module
33
Compass
Normal
Check azimuth during installation
The required installation tools may vary depending on the conditions at the site.
In addition to the basic tools, a protractor, GPS receiver, ladder, safety equipment, cleaning
tools, and so on should also be prepared in consideration of the site conditions.

Chapter 2 Installing System
RFD01F Series Installation Manual v1.0 9
© Samsung Proprietary and Confidential
Chapter 2 Installing System
Installation Procedure
The procedure to install the RRU is as follows:
Figure 3. Procedure to Install the RRU
Make sure that the power switch of the power supply is OFF when installing the
system. Installing the system with the power switch ON may cause system damage
or fatal human injury when connecting or disconnecting the cables.
To prevent the risk of electrical shock do not wear accessories such as watches and
rings.
Foundation Work
Unpacking and Transporting
Fixing System
Unpacking Items
Bringing in Items
Marking and Drilling (only wall type)
System Leveling
Fixing System