Samsung PC6 UC N Series User manual

Airconditioner
InstallationManual
PC6*UC**N
•Thank you forpurchasing this Samsung airconditioner.
•Before operating this unit, please read this manual carefullyand retain it forfuture reference.

2English
Installingthe360CSTpurificationpanel
ƟцΧʪϑͱ˙ߥߨߢʀɇϑϑʪϩϩʪɇθΧЇθѣʀɇϩͱ
panels
TypeA:Squarepanel Type B: Circularpanel
Accessories
M4 XL25 bolt (4)
(TypeA only) Installation manual(1)
Usermanual(1) M4screw(4)
CAUTION
• Afterinstalling the product, the installation technician
must showthe userhowto use the airconditioner.
NOTE
• M4 screwtightening torque:1.2–1.8 N·m
Ãϑϩɇ˝ϩ˵ʪɇθΧЇθѣʀɇϩͱϩ
1 Remove the protective cover.
2 Removethe electrical system unit cover.
3 ŵʪͱЭʪϩ˵ʪѣϩʪθ˙θͱϩ˵ʪɇθΧЇθѣʀɇϩͱϩ࢏
Turn the latch
afterremoving
the safetyhook
Pull out withthe
handle

3
English
4 Ƹϑʪϩ˵ʪ˵ͱͱϑϩͱ˙ɇϑϩʪϩ˵ʪɇθΧЇθѣʀɇϩͱϩϩͱϩ˵ʪ
indoorunit, and then tighten the screws.
CAUTION
• Make sure the hooks on the airpurification kit have
been fastened properly.
5 Remove the protective cover.
6 Connectthe powerand communication lines, and then
ѣуϩ˵ʪиθ˝ɇϑϑ˵ͱиϩ˵ʪѣ˝Їθʪ࢏Ęʪуϩࡥɇϩϩɇʀ˵ϩ˵ʪ
electrical system unit coverand then the protective
cover.
Powercable
Communicationline
CAUTION
• If installing the AM********** model, make sure
the two powerlines, going intothe indoorunit, are
fastened using a single compressed ring terminal.
7 ŵʪͱЭʪϩ˵ʪΧθͱϩʪʀϩЭʪϩɇΧʪͱϩ˵ʪѣϩʪθ࢏
8 ϑϑʪɵʪϩ˵ʪΧЇθѣʀɇϩͱѣϩʪθ࢏
Turn the
latchand
hang the
safetyhook.
NOTE
• Push the purificationfilterinside and turn both latches
until a click sound is audible.
CAUTION
• If the purificationfilteris not secured properly, noise
mayoccur.

4
Installingthe360CSTpurificationpanel
English
9 Removethe protectivetape covering the dust sensor
ʪϩͱϩ˵ʪɇθΧЇθѣʀɇϩͱϩ࢏
CAUTION
• Afterinstallation, be sure to checkthat the protective
film is removed.
– Removethe protectivetape attached on the
purification filter.
– Remove the protective tape forblocking the panel
dust sensorinlet.
• If the protectivetape is not removed, the purification
filtermaynot operate.
Installingthegrille
1 Make sure you connectthe (two)wires on the grille to
the clip wires on the indoorunit.
NOTE
• Before installing the grille, make sureyou connect the
(two) safety rings to both ends of the grille to prevent
it from falling.
2 Attach the grille byturning it clockwise until a‘click’
sound is audible.
Closed
NOTE
• If the grille is installed correctly,the indicatoron the
indoorunit is at a 90 degree anglewith the Samsung
ͱ˝ͱͱϩ˵ʪ˝θʪɇʒϩ˵ʪϩθɇ˝ʪʪуϩϩͱϩ˵ʪͱʀ
engraved on the indoorunit is aligned with the
triangle on the grille.
• The grille cannot be assembled in otherdirections.
Installingthepanelfrontforthe
ceilingtype
1 Removethe fourcoverpanels fromthe panel front.
NOTE
• To remove the coverpanels, use the twotongues at
the ends of each coverpanel.

5
English
2 Push the fourcorners of the panel front toward the
indoorunit body one at a time untilyou hear“click”so
that theyare assembled in place.
NOTE
• Afterassembling the panelfront in place,you can
slightlyadjust its position left and right. If required,
adjust the position of the panelfront so that it aligns
with the ceiling opening.
3 Push the centres of the foursides of the panel front
toward the indoorunit body one at a time until you
hear“click” so that theyare hooked in place.
4 Insert halfwaythe fourscrews into the fourholes on
the panel front. Then fasten the screws tightlyuntil
there is no gap between the ceiling and the panel front.
5 Place each coverpanel on a cornerof the panel front.
Ɵ˵ʪΧЇϑ˵ϩ˵ʪʀͱЭʪθΧɇʪЇΧиɇθʒЇϩϩϑѣθц
assembled to the panel front.
6 A˵ʪʀи˵ʪϩ˵ʪθϩ˵ʪΧɇʪ˙θͱϩϑѣθцѣуʪʒϩͱϩ˵ʪ
indoorunit body.
NOTE
• Make sure that the screws are fastened tightly until
there is no gap between the ceiling and the panel.
• If the panel is installed incorrectly, airmayleak out.

6
Installingthe360CSTpurificationpanel
English
Installingthecircularpanelonthe
indoorunit
1 Insert the decoration panelthe indoorunit body.
Then rotate the decoration panel clockwise until it is
ɇϑϑʪɵʪʒѣθц࢏
• Ceiling type
• Open type
NOTE
• Make sure that the decoration panel is installed
correctly sothat there is no gap betweenthe ceiling
and the panel.
• If the panel is installed incorrectly, airmayleak out.
CAUTION
• Make sure to only apply paints and varnishes forresins
(ABS, HIPS) orpaint thinners.
Ifyou applylacquers forgeneral use on the panel, it
maylead to discoloration orerosion on the surface of
the panel.

7
English
Settingtheindoorunitaddressandsetupoptions
Commonstepsforsettingthe
addressesandoptions
AR-KH0**remotecontrol(for360cassetteonly)
Timerbutton
Temperature
button
Modebutton
Wheel
Settingthe
optionvalues
Enteringthe modefor
settingtheoptions
NOTE
• The remote control display mayvarydepending on the
model.
1 Enterthe mode forsetting the options:
a Remove the batteries from the remote control.
b While holding down the (Temp)and (Timer)
buttons simultaneously, insertthe batteries into the
remote control.
c Make sure that you are enteredto the mode for
setting the options:
2 Set the option values.
CAUTION
• The total numberof available options are 24: SEG1to
SEG24.
• Because SEG1, SEG7, SEG13, and SEG19 are the page
options used bythe previous remote control models,
the modes to setvalues forthese options are skipped
automatically.
• Set a 2-digitvalue foreach option pairin the following
ͱθʒʪθࡤƊkߤɇʒƊkߥƊkߦɇʒƊkߧƊkߨɇʒ
ƊkߪƊk߫ɇʒƊkߣߢƊkߣߣɇʒƊkߣߤƊkߣߦ
ɇʒƊkߣߧƊkߣߨɇʒƊkߣߩƊkߣߪɇʒƊkߤߢ
ƊkߤߣɇʒƊkߤߤƊkߤߥɇʒƊkߤߦ
SEG1 SEG2 SEG3 SEG4 SEG5 SEG6
0XXXXX
SEG7 SEG8 SEG9 SEG10 SEG11 SEG12
1XXXXX
SEG13 SEG14 SEG15 SEG16 SEG17 SEG18
2XXXXX
SEG19 SEG20 SEG21 SEG22 SEG23 SEG24
3XXXXX
On(SEG1toSEG12) Off(SEG13toSEG24)

8
Settingtheindoorunitaddressandsetupoptions
English
Take the steps presented in the following table:
Steps Remotecontroldisplay
1 Set the SEG2 and SEG3 values:
a Set the SEG2value byrotating theWheel
counterclockwise until the valueyou want to set appears
on the remote control display. SEG2
b Set the SEG3value byrotating theWheel clockwise until
the valueyouwant to set appears on the remote control
display.
SEG3
Whenyou rotate theWheel,values appearin the following order:
2 Press the (Mode) button. Cool and On appearon the remote control display.
3 Ɗʪϩϩ˵ʪƊkߦɇʒƊkߧЭɇЇʪϑࡤ
a Set the SEG4value byrotating theWheel
counterclockwise until thevalueyouwant to set appears
on the remote control display. SEG4
b Ɗʪϩϩ˵ʪƊkߧЭɇЇʪɵцθͱϩɇϩ˝ϩ˵ʪǮ˵ʪʪʀͱʀиϑʪЇϩ
thevalueyouwant to set appears on the remote control
display.
Ɗkߧ
Whenyou rotate theWheel,values appearin the following order:
4 Press the (Mode) button. Dry and On appearon the remote control display.
5 Ɗʪϩϩ˵ʪƊkߨɇʒƊkߪЭɇЇʪϑࡤ
a Ɗʪϩϩ˵ʪƊkߨЭɇЇʪɵцθͱϩɇϩ˝ϩ˵ʪǮ˵ʪʪ
counterclockwise until thevalueyouwant to set appears
on the remote control display.
Ɗkߨ
b Set the SEG8value byrotating theWheel clockwise until
the valueyouwant to set appears on the remote control
display.
SEG8
Whenyou rotate theWheel,values appearin the following order:

9
English
Steps Remotecontroldisplay
6 Press the (Mode) button. Fan and On appearon the remote control display.
7 Set the SEG9 and SEG10 values:
a Set the SEG9value byrotating theWheel
counterclockwise until thevalueyouwant to set appears
on the remote control display. SEG9
b Set the SEG10 value byrotating theWheel clockwise until
the valueyouwant to set appears on the remote control
display.
SEG10
Whenyou rotate theWheel,values appearin the following order:
8 Press the (Mode) button. Heat and On appearon the remote control display.
9 Set the SEG11 and SEG12 values:
a Set the SEG11value byrotating theWheel
counterclockwise until thevalueyouwant to set appears
on the remote control display. SEG11
b Set the SEG12 value byrotating theWheel clockwise until
thevalueyouwant to set appears on the remote control
display.
SEG12
Whenyou rotate theWheel,values appearin the following order:
10 Press the (Mode) button. Auto and Off appearon the remote control display.

10
Settingtheindoorunitaddressandsetupoptions
English
Steps Remotecontroldisplay
11 Ɗʪϩϩ˵ʪƊkߣߦɇʒƊkߣߧЭɇЇʪϑࡤ
a Set the SEG14 value byrotating theWheel
counterclockwise until the valueyou want to set appears
on the remote control display. SEG14
b Ɗʪϩϩ˵ʪƊkߣߧЭɇЇʪɵцθͱϩɇϩ˝ϩ˵ʪǮ˵ʪʪʀͱʀиϑʪЇϩ
thevalueyouwant to set appears on the remote control
display.
Ɗkߣߧ
Whenyou rotate theWheel,values appearin the following order:
12 Press the (Mode) button. Cool and Off appearon the remote control display.
13 Ɗʪϩϩ˵ʪƊkߣߨɇʒƊkߣߩЭɇЇʪϑࡤ
a Ɗʪϩϩ˵ʪƊkߣߨЭɇЇʪɵцθͱϩɇϩ˝ϩ˵ʪǮ˵ʪʪ
counterclockwise until thevalueyouwant to set appears
on the remote control display.
Ɗkߣߨ
b Set the SEG17 value byrotating theWheel clockwise until
thevalueyouwant to set appears on the remote control
display.
SEG17
Whenyou rotate theWheel,values appearin the following order:
14 Press the (Mode) button. Dry and Off appearon the remote control display.
15 Set the SEG18 and SEG20 values:
a Set the SEG18value byrotating theWheel
counterclockwise until thevalueyouwant to set appears
on the remote control display. SEG18
b Set the SEG20value byrotating theWheel clockwise until
the valueyouwant to set appears on the remote control
display.
SEG20
Whenyou rotate theWheel,values appearin the following order: