Be sure to first follow the
Quick Start Guide on
the reverse side of this guide
to complete initial setup
of your headset.
Features and
Functions Guide
SAMSUNG
Bluetooth Mono Headset
WEP170
To turn the headset on,
Press and hold the Multi-Function button for 1 to 2
seconds until you see a burst of 3 flashes on the blue
indicator light, then release.
You will hear a tone and see the indicator light flashes
while the power is on (see Meaning of the indicator
light of this guide).
To turn the headset off,
Press and hold the Multi-Function button for 3 to 5
seconds until you see a burst of 3 flashes on the blue
indicator light, then release.
You will hear series of 2 tones and see the indicator
light stops flashing.
Turn headset on/off
For optimal performance, wear Samsung WEP170 and
your Bluetooth phone on the same side of your body.
In general, you will get better
performance when there are no
obstructions (including parts of
your body) between the headset
and the phone.
Wear the headset Change for use on other ear
Use enhanced features
Meaning of the indicator light
Samsung Bluetooth headset WEP170 is ready to wear
on the right ear. If you prefer the left, gently rotate
the ear hook.
Press [] on the side of the headset to increase
the volume level and press [] to decrease the
volume level.
Adjust the volume
Using phone’s keypad
1
Dial number on keypad.
2
Press phone’s “send” key.
Using voice-activated dialing
(after you’ve set up voice tags on your phone)
1
Long Press and release Multi-Function Button once.
2
You’ll then hear the voice-activation tone; say the
name of the person you wish to call.
End a call
• Press and release Multi-Function Button once.
OR
• End call from phone’s keypad.
Answer a call
• After you hear the ring tone, press and release
Multi-Function Button once.
OR
• Answer the call with your phone’s keypad. You may then
need to transfer the call to the headset by pressing and
releasing Multi-Function Button once.
(depending on your phone)
Call-waiting
•
(Recommended) Use standard method from your phone’s
keypad which typically involves pressing the “send” button.
OR
• Long press and release Multi-Function Button once to
answer the incoming call and toggle between calls. (some
phones do not support this headset feature)
Make calls
Enhanced features are available for phones that support the
hands-free Bluetooth profile. Check your phone’s instruction
guide or contact the phone manufacturer if you are not sure
if your phone supports the hands-free Bluetooth profile.
Once you’re done pairing, the following headset
features will be available:
• Last number redial (when not on a call)
While the headset is on, press and hold Multi-Function Button
release.
• Rejecting an incoming call (when not on a call)
When your phone rings, press and hold Multi-Function Button
release.
• Call-waiting (swapping between 2 calls)
When your phone notifies you of another incoming call while
you’re on a call,press and hold Multi-Function Button release.
• Putting a call on hold
While you’re on a call, press and hold Multi-Function Button
release immediately. Repeat to retrieve the call.
Flashes in
blue every
8 seconds.
Quick series
of 2 tones.
(Active mode
starts.)
The headset is in Active mode.
• The headset has an active
call in progress.
• You can talk up to 8 hours.
Flashes in
blue every 3
seconds.
Quick series
of 2 tones.
(Standby
mode starts.)
The headset is in Standby mode.
• The headset is waiting
for a call.
• The headset can be in
Standby mode up to 200
hours.*
Flashes in
red instead
of blue.
5 tones every
20 seconds.
The battery of the headset is
low. Recharge the battery.
• 3 to 5 minute of talk time
left.
Important:
Headquarters:
1301 East Lookout Drive Suite 150
Richardson, TX 75082
Internet Address:
http://www.samsungusa.com
Light Tone Status
*
Depending on the phone type and usage, the actual time may vary.
Troubleshooting
My phone does not find my headset.
Make sure the blue indicator light on your
headset turns on when your phone is
searching for devices.
My headsest worked before but now it is
not working.
Make sure your phone is on and the Bluetooth
feature is turned on in your phone.
If the Bluetooth feature has been turnned off
or was turned on only temporarily, you may
need to restart the Bluetooth feature.
If you have confirmed the Bluetooth feature is
on in your phone, pair your phone and
headset again.
NOTE:
Record voice tag from headset for better reception.
NOTE:
Do not hold the Multi-Function Button button down too long
when making, ending, or answering a call. This should only
be a quick tap, so you don’t put the headset into pairing
mode by accident.
