Samsung WEP180 - Headset - Over-the-ear User manual

Guide No.: GH68-12459A
09/2006. Rev. 1.0
Quick Start Guide
Samsung
Bluetooth®Headset
WEP180
Thank you for purchasing the Samsung Bluetooth
Mono Headset WEP180, we hope you will be
delighted with its operation.
Take a moment before you get started to
familiarize yourself with your new headset.
Make sure you have the following items with your
headset:
Make sure you have the following items with your
headset:
Travel adapter, User’s Guide, 1 ear hookTravel adapter, User’s Guide, 1 ear hook
Check the accessoriesCheck the accessories Charge your headsetCharge your headset
Charge the headset's battery fully before using
the headset for the first time.
1 Plug the travel adapter into the jack on the
headset.
2 Plug the travel adapter into the electrical
outlet.
3 Remove the travel adapter from the headset.
• Charge the headset until the red light on the
headset turns to blue.
• The headset will be fully charged in
approximately 2 hours 30 minutes.
Before you can use your headset, you must pair it
with your phone.
Put your headset in
pairing mode
Turn on Bluetooth on your
phone and pair with headset
Your phone and headset are now paired and
ready to make and receive calls. To confirm
they are operating properly, make a call:
1 Place the headset over your ear.
See Wearing the headset on the reverse
side of this guide.
2 On your phone, make a call to the number
you want.
3 If your phone and headset are successfully
paired, you will hear ringing on the headset.
After you have successfully paired your phone
and headset, you do not need to repeat these
initial setup steps each time you use the
headset.
Test and use
Using your WEP180
See Features and Functions Guide
on the reverse side of this guide
for information on using your
WEP180.
1 Ensure that the headset is off (see Turn
headset on/off on the reverse side of this guide).
2 Press and hold the Multi-Function button until
the indicator light turns on in blue
(approximately 8 seconds).
Before using your headset
Multi-Function
button
Earpiece
Volume control
buttons
Indicator light
Adapter jack
Microphone
NOTES:
• The headset cannot be used while charging.
• Use only a Samsung-approved charger or adapter.
Start here
Charge your headset
Put your headset in pairing mode
Turn on Bluetooth on your phone and
pair with headset
Test and use
Get connected in 4 quick steps
Headquarters:
1301 East Lookout Drive Suite 150
Richardson, TX 75082
Internet Address:
http://www.samsungmobileusa.com/
accessories
Customer Care Center:
1-888-987-4357
NOTE:
The items supplied with your headset and the accessories
at your Samsung dealer may vary, depending on you
country or service provider.
• Bluetooth version: 2.0 (compatible with devices of
Bluetooth version 1.1 or higher)
• Supported Bluetooth profiles:
- Headset profile
- Hands-free profile
1 Set your Bluetooth phone to discover the
headset by following your phone's guide.
Typically, the steps involve going to the Settings,
Connection, or Bluetooth menu on your
phone and then selecting the option to discover
Bluetooth devices.
Your phone will find the Samsung WEP180
headset. your headset will be displayed as
Samsung WEP 180/185.
2 Select your headset.
3 When the phone asks if you want to pair with it,
confirm by selecting Yes or OK.
4 Enter the headset passkey or PIN, 0000.

Be sure to first follow the
Quick Start Guide on
the reverse side of this guide
to complete initial setup
of your headset.
Features and
Functions Guide
SAMSUNG
Bluetooth®Headset
WEP180
To turn the headset on,
Press and hold the Multi-Function button for
4 seconds until you see 4 blue flashes on the
indicator light, then release.
You will hear a tone and see the indicator light
flashes while the power is on
(see Meaning of the indicator light of this guide).
To turn the headset off,
Press and hold the Multi-Function button for
4 seconds until you see blue flashes on the indicator
light, then release.
You will hear series of 2 tones and see the indicator
light stops flashing.
Turn the headset on/off
Wear the headset on your ear.
In general, you will get better performance
when there are no obstructions
(including parts of your body)
between the headset
and the phone.
Wear the headset Use the ear hook
Use enhanced features
Meaning of the indicator light
Attach the supplied hook to the headset to make
wearing the earpiece more comfortable.
Depending on which ear you are going to wear the
headset, simply adjust the hook accordingly.
Make a voice activated call
If the phone’s voice recognition feature is on, you can
make a voice activated call.
1 Press the Multi-Function button once. You will hear the
voice-activation tone.
2 Say the name of the person you wish to call.
Depending on your phone, this feature may not be
supported.
Redial the last number
When the headset is connected with the phone via the
Hands-free profile, press and hold the Multi-Function
button.
When the headset is connected with the phone via the
Headset profile:
1 Press the Multi-Function button to access the recent
call list.
2 If necessary, press [] or [] to scroll to the number
you want.
3 Press the Multi-Function button to dial the selected
number.
End a call
Press the Multi-Function button.
Answer a call
When a call comes in, the headset sounds the ring tone
and flashes the blue indicator twice. Press the Multi-
Function button.
Adjust the volume
Press [] on the side of the headset to increase the volume
level and press [] to decrease the volume level.
Make calls
Enhanced features are available for phones that support the
hands-free Bluetooth profile and enhanced features.
• Reject a call
When you receive a call, press and hold the Multi-Function
button to reject the call. Depending on your
phone's setting or type, this feature may not be
supported.
• Answer a second call
When your phone notifies you of another incoming call while
you are on a call, press and hold the Multi-Function button.
You can switch between calls by pressing and holding it again.
Depending on your phone, this feature may not be supported.
• Place a call on hold
While you are on a call, press and hold the Multi-Function
button.
To retrieve the call, press and hold the Multi-Function button
again.
Depending on your phone, this feature may not be supported.
Flashes in
blue every
8 seconds.
Quick series
of 2 tones.
(Active mode
starts.)
The headset is in Active mode.
• The headset has an active
call in progress.
• You can talk up to 6 hours.
Flashes in
blue every 3
seconds.
Quick series
of 2 tones.
(Standby
mode starts.)
The headset is in Standby mode.
• The headset is waiting
for a call.
• The headset can be in
Standby mode up to 110
hours.*
Flashes in
red instead
of blue.
5 tones every
20 seconds. The battery of the headset is
low.
• There is less than 10% of
battery power left. Recharge
the battery.
Important:
Light Tone Status
*Depending on the phone type and usage, the actual time
may vary.
Left Right
Troubleshooting
My phone does not find my headset.
Make sure the blue indicator light on your
headset turns on when your phone is
searching for devices.
My headsest worked before but now it is
not working.
Make sure your phone is on and the Bluetooth
feature is turned on in your phone.
If the Bluetooth feature has been turnned off
or was turned on only temporarily, you may
need to restart the Bluetooth feature.
If you have confirmed the Bluetooth feature is
on in your phone, pair your phone and
headset again.
Headquarters:
1301 East Lookout Drive Suite 150
Richardson, TX 75082
Internet Address:
http://www.samsungmobileusa.com/
accessories
Customer Care Center:
1-888-987-4357