Samsung HARMAN Epica DGX 16 Installation instructions

Technical Support Guide
Epica DGX 16/32 and Enova DGX Cable Management
1
Technical Support Guide
Epica DGX 16/32 and Enova DGX Cable Management
Applicability
This Technical Support Guide provides instructions for installing (and removing) cable management bars for SC Optical Boards on
Epica DGX 16/32 Distribution Matrices and for DXLink Fiber Boards on all Enova DGX Digital Media Switchers (DGX 8/16/32/64
and DGX 100 Series).
Attaching Cable Management Bars
Items included in Sales # FG1056-700 (Cable Bar Kit only) and in Cable Bar Kit # KA1056-700 (which ships with SC Optical and
DXLink Fiber Boards):
1 cable management bar
4 screws (3 required)
When cable management bars are used, they need to be installed before the cables are attached.
CAUTION: Do not severely bend or kink the fiber optic cable. Irreversible damage can occur. Refer to the physical limitations (bend
radius) specified for the cable by the manufacturer.
To install a cable management bar:
1. 32x32 size enclosures only – Loosen the two captive screws that hold the connector numbering plate at the top of the
connectors. Remove the connector numbering plate and set aside.
Connector numbering plate
FIG. 1 Connector numbering plate (Epica DGX 32 shown)
2. Align the two screw holes on the end of the cable management bar with the two screw holes on the end of the board as shown
in FIG. 2. (Note the position of the long part of the bar in relation to the screw holes.)
Epica DGX 32, Enova DGX 32, Enova DGX 3200
Fasten cable management bar with
two screws on one end and one on
the other end (do not over tighten)
Tie cable to cable management
bar far enough from connector to
allow for manufacturer’s
recommended bend radius
Epica DGX 16, Enova DGX 8/16/64, Enova DGX 800/1600/6400
NOTE: On Epica DGX 16, Enova DGX 8/16/64, and Enova DGX 800/1600/6400 enclosures, the orientation of the cable
management bars is reversed from boards in the left slots to boards in the right slots.
Board in left slot Board in right slot
FIG. 2 Installation of cable management bars
3. Insert and tighten the two screws at the end of the cable management bar (do not over tighten the screws).
4. Align, insert, and tighten the single screw at the other end of the cable management bar (do not over tighten).
TIP: When using cable management bars with fiber boards, we recommend the use of soft ties (e.g., Velcro type hook-and-loop
strips) instead of nylon cable ties, which can break fiber cables.

5. Tie the cable to the cable management bar far enough from the connector to allow for the manufacturer’s recommended bend
radius. The bend radius for AMX SC terminated fiber cables is 2 inches (5 cm).
6. 32x32 size enclosures only – Replace the connector numbering plate that was removed in Step 1.
Technical Support
If this Technical Support Guide has not satisfactorily answered your questions regarding installing cable bars or the system is not
operating as expected, please contact your AMX representative or technical support. Have the product’s serial number ready (it is
normally located on the rear of the enclosure).
We recommend recording the product’s serial number in an easily accessible location.
AMX Technical Support Contact Number: [phone]
© 2021 Harman. All rights reserved. SmartScale, NetLinx, Enova, AMX, AV FOR AN IT WORLD, and HARMAN, and their respective logos are
registered trademarks of HARMAN. Oracle, Java and any other company or brand name referenced may be trademarks/registered trademarks of
their respective companies.
AMX does not assume responsibility for errors or omissions. AMX also reserves the right to alter specifications without prior notice at any time.
The AMX Warranty and Return Policy and related documents can be viewed/downloaded at www.amx.com.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 AMX.com | 800.222.0193 | 469.624.8000 | +1.469.624.7400 | fax [phone]
93
-1056-054 REV: G
Last Revised: 2021-05-13