Samsung SNK-D5081 User manual

1

2
CONTENTS
CHAPTER 1 GET CLOSE TO NVR...........................................................................................................6
1.1 FRONT PANEL .....................................................................................................................................6
NVR Front Panel (Model: SNR-D5401)..............................................................................................6
1.2 BACK PANEL .......................................................................................................................................6
NVR Back Panel (Model: SNR-D5401) ..............................................................................................6
1.3 REMOTE CONTROLLER........................................................................................................................7
1.4 INSTALL HARD DRIVE...........................................................................................................................8
1.5 CONNECT EXTERNAL EQUIPMENT .........................................................................................................9
1.6 CONNECT CAMERA..............................................................................................................................9
1.7 CONNECT NVR.................................................................................................................................10
1.8 HOW TO CONNECT THE RJ45WATERPROOF CABLE TO A LAN CABLE....................................................10
1.9 POWER CABLE WATER PROOFING......................................................................................................13
1.10 INSTALLING THE CAMERA..................................................................................................................14
CHAPTER 2 NVR BOOT UP...................................................................................................................15
2.1 SYSTEM INITIALIZATION......................................................................................................................15
2.2 STARTUP WIZARD..............................................................................................................................15
2.3 MAIN INTERFACE...............................................................................................................................17
CHAPTER 3 NVR MENU.........................................................................................................................18
POPUP MENU .........................................................................................................................................18
MAIN MENU GUIDE..................................................................................................................................19
3.1 MAIN MENU......................................................................................................................................20
3.2 PARAMETER......................................................................................................................................21
3.2.1 Display .....................................................................................................................................21
3.2.2 Record .....................................................................................................................................24
3.2.3 Network....................................................................................................................................25
3.2.4 Alarm........................................................................................................................................29
3.3. RECORD SEARCH.............................................................................................................................30
3.3.1 Record Search.........................................................................................................................30
3.3.2 Event Search ...........................................................................................................................32
3.3.3 Play Backup Files ....................................................................................................................34
3.4 DEVICE.............................................................................................................................................36
3.4.1 HDD .........................................................................................................................................36
3.4.2 Cloud Storage..........................................................................................................................37
3.5 SYSTEM............................................................................................................................................38
3.5.1 General ....................................................................................................................................38

3
3.5.2 Users........................................................................................................................................40
3.5.3 Info...........................................................................................................................................42
3.5.4. Log..........................................................................................................................................43
3.6ADVANCED........................................................................................................................................43
3.6.1 Maintain ...................................................................................................................................43
3.6.2 Events......................................................................................................................................45
3.7 SHUTDOWN.......................................................................................................................................45
3.8 MENU LOCK......................................................................................................................................46
3.9 SPLIT MODE......................................................................................................................................46
3.10 STREAM SWITCH.............................................................................................................................46
3.11 VIEW IMAGE QUALITY ......................................................................................................................46
3.12 RECORD SEARCH............................................................................................................................47
3.13 START SEQUENCE...........................................................................................................................47
CHAPTER 4 WEB APPLICATION MANAGER.......................................................................................47
4.1 DOWNLOADAND INSTALLATION OF PLUGIN..........................................................................................47
4.1.1 Download and Installation of Plugin for IE...............................................................................48
4.1.2 Download and installation of plugin for Mac SAFARI. .............................................................50
4.2WEB APPLICATION MANAGER LOGIN ..................................................................................................52
4.3 LIVE INTERFACE ................................................................................................................................53
4.3.1 LIVE .........................................................................................................................................53
4.3.2 Playback ..................................................................................................................................55
4.3.3 Remote Setting........................................................................................................................58
4.3.4 Local Setting............................................................................................................................70
4.3.5 Logout......................................................................................................................................70
CHAPTER 5 MOBILE APP......................................................................................................................71
CHAPTER 6 APPENDIX..........................................................................................................................73
6.1 TROUBLESHOOTING...........................................................................................................................73
6.2 USAGE MAINTENANCE.......................................................................................................................74
6.3 PRODUCT SPECIFICATION..................................................................................................................75
6.4ACCESSORIES ATTACHED (SNK-D5081)............................................................................................78

4
SAFETY INSTRUCTION
Please carefully read the following safety instructions so as to avoid personal injuries and prevent
the equipment and other connection devices from being damaged.
1. Please use the power supply enclosed or specified by the manufacturer.
Never operate the equipment by using unspecified power supply.
2. Never push objects of any kind through openings of the NVR to avoid electric shock or other
accidents.
3. Do not put the equipment in a dusty location.
4. Do not place the equipment under the rain or humid environment like the basement.
If the equipment is accidentally in contact with water, please unplug the power cable and
immediately contact technical support.
5. Keep the surface of the equipment clean and dry.
Use a soft damp cloth to clean the outer case of the NVR. (Do not use liquid aerosol cleaners.)
6. Do not operate if any problems are found.
If there is a strange smell or sound from the NVR, unplug the power cable and contact technical
support.
7. Do not try to remove the NVR cover to avoid electrical shock.
8. Handle with care.
If NVR does not work properly, please contact technical support for repair or replacement.
9. Install and place the equipment in a well ventilated area. The NVR system includes a HDD, which
produces large amount of heat during operation. As a result, do not block the ventilation vents
(on the top, bottom, sides and the back of the NVR).
10. The power adapter should only be connected to the NVR. Do not connect it to additional
equipment or else the NVR may restart repeatedly due to insufficient power.
11. Do not install near any heat sources such as radiator, stove, and other machinery or devices
(including speakers) that produce large amount of heat.
12. If the provided plug does not fit your outlet, please call technical support for assistance.
13. Protect the power cord from being walked on or pinched particularly at the plug level and each
ends of the cord.
14. Only use attachments/accessories specified by the manufacturer.
15. Only use the cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the system. When a cart is used, use caution when moving the cart
and the device to avoid injury from tip-over.
16. Unplug the device during lightning storms or when unused for long periods
of time.
17. Refer all servicing to qualified service personnel. Servicing is required when the device has
been damaged in any way, such as power-supply cord or plug is broken, liquid has been spilled
or objects have fallen onto the device, exposed to rain or moisture, does not operate normally,
or has been dropped.
18. This equipment is indoor use and all the communication wiring are limited to inside of the
building.
19. CAUTION: Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used
BatteriesAccording to the Instructions.

5
Standards Approvals
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.

6
Chapter 1 Get Close to NVR
1.1 Front Panel
Tips: NVR is the abbreviation of Network Video Recorder.
NVR Front Panel (Model: SNR-D5401)
SN
Key or LED
Mark
Function
1
Power indicator lamp
PWR
When the indicator lamp turns on in green color, it
means that the NVR is powered normally.
2
Hard drive indicator lamp
HDD
If the “Red” indicator flashes, the hard drive is being
read or written to.
3
IR Signal Reception Port
For reception of IR remote control signal
4
USB
USB
USB Port
1.2 Back Panel
NVR Back Panel (Model: SNR-D5401)
SN
Physical Interface
Connection Instructions
1
e-SATA
Connect to a e-SATA HDD
2
VGA Output
Connect VGA display device, such as PC monitor.
3
AUDIO OUT
No Function
4
LINE IN
No Function
5
Power Switch
Power the NVR on/off
6
Power Port
Connect to power cable provided along with the device.
7
USB
USB Port
8
HDMI Port
Connect to monitor
9
WAN Port
Router network I/O port/for connection to network camera
10
LAN Port
LAN: network port, PoE compliant, and capable of supplying
power to camera.

7
1.3 Remote Controller
Item
Key title
Key function
1
0-9
Numeric key
2
ALL
Multiple display mode
3
Mute
No Function
4
Menu
Enter into Main menu/Exit
5
Submenu
Go to Submenu
6
▲
Up arrow key
7
SEL
Select key/Edit key
8
Left/Right key; Decrease/increase parameter
value of control bar.
9
▼
Down arrow key
10
Rewind key
11
Forward key
12
Enter into record search menu / Play key
13
●
Record key
14
■
Stop manual record; stop playing
15
Pause/Step forward key

8
1.4 Install Hard Drive
Notes: Do not remove the hard drive when NVR is operating.
Installation of Hard Drive:
(1) When power supply is disconnected, remove the screws at both sides with screwdriver, then
remove the screws on the rear board, and then remove top cover of NVR.
(2) Connect data and power cables of hard drive to motherboard. Mount the hard drive by
mounting it onto the rack and connecting the power and data cables. Two groups of screw
mounting holes are provided in the base frame of the NVR, respectively for installation of 3.5'
hard drive and 2.5' hard drive. User should make selection based on their hard drive size.
(3) First mount the screws onto the rear board and then mount the sides.

9
1.5 Connect external equipment
Connect the cameras to the NVR via the network cables. If you choose not to power the cameras
via the LAN ports, be sure to use a 12V power adapter for power each camera.
Connect your monitor to the NVR using a VGA or HDMI cable to its respective port.
Connect the NVR to the power cable that‟s supplied with the system.
1.6 Connect Camera
Connecting the Camera (SNC-4241BE)
Equipped with the IR LED and the illumination sensor, the camera enables you to monitor at all
times, day and night. The camera is suitable for both indoor and outdoor use.
Do not fully expose the camera to rain. The camera must be installed under a shelter to avoid
exposure to excessive rain or moisture.
Name
Description
1
Lens
3.6mm focal length enables you to monitor at a wider field of
view.
2
IR LED
Infrared LED lights are controlled by the illumination sensor.
3
Illumination Sensor
Detects incoming light to control the IR LED.
4
IPC Network Port
Connect to NVR via POE port or switch
5
Power Cable
Use to power the camera if you would l like to power up the
camera by using separate DC 12V power adaptor.

10
1.7 Connect NVR
The following figures are based on Model SNR-D5401.
1.8 How to connect the RJ45 waterproof cable to a LAN cable
Components Introduction
RJ45 female
modular jack
(mold)
RJ45 male connector
Fastening rubber
gasket (male)
Fastening back cover
Waterproof
rubber gasket
(Female)
RJ45 connector protector cap

11
Install step-1
Pass the LAN cable through each components as shown below:
Fastening back cover →Waterproof rubber gasket →RJ45 connector protector cap
Install step-2
RJ45 male connector
※(Caution) Gasket direction
RJ45 male and
female
connectors
Remark: keep waterproof
gasket separate

12
Install step-3
Install step-4
Tightly screw the protector cap
Fit the rubber gasket into the RJ45 connector protector cap so that the inner diameter of
waterproof rubber gasket is tighten when the back cap is screwed on.
Tightly screw the back cap clockwise.

13
1.9 Power cable Water Proofing
When you install it outside of the building, please waterproof the power cable with waterproof butyl
rubber tape (can be purchased in hardware stores) so that water does not leak to the gap of the cable.
1. Connect the power cables.
2. Wrap the cable jacket (Area A) and the cable connection area with waterproof (butyl rubber) tape so
that more than half of the butyl rubber tape is overlapped.
If the connected cable jacket is poorly wrapped, water can leak into the connectors causing
damage to the camera.
Waterproofing butyl tape is made of butyl rubber that can extend twice as long as its original length.
If the power cable terminal is not in use, wrap it with waterproofing tape.

14
1.10 Installing the camera
The camera can be installed on the wall, ceiling, shelf or a desired position using the provided
mounting bracket.
1.Adhere the installation template onto the ceiling and use it as installation locating tool. (Please refer to
Page 17 of Quick Guide.)
2. Choose an installation site that can sufficiently support the weight of the camera to be installed.
3. Attach the camera bracket to the wall using the supplied screws.
4. Adjust the direction of the camera to the desired direction, and tighten the bracket.
5. Adjust the camera angle as needed.
6. Connect the camera cable to the camera.
Take caution when installing the camera outdoors because the cable connectors may be wet with
moisture or with dirt buildup.
Although the camera is IP66 rated, direct exposure to water or moisture may cause problem such
as condensation.

15
Chapter 2 NVR Boot up
2.1 System Initialization
After connecting the NVR power cable to the wall outlet, press the power button and the the
initializing screen will appear.
2.2 Startup Wizard
After the NVR startup is complete, the startup wizard will be displayed. If no changes will be
made in the future after you turn the system on, you may click on “To disable Startup Wizard after
reboot?” to cancel.
Wizard setting menu includes: Homepage, Network setup, IPC setup, Record Schedule and
hard disk maintenance.
1．Homepage. Set admin password. Please create a user name and password for your Device.
Password MUST be 8-13 characters long, and the combination of two kinds of characters at least
(ex. Letter, number and special character).After restart, use the user name and password set above
to log in.
Note: The illustration in the user manual
may not be the same as the menu interface
in your monitor. All the illustrations are for
users‟ reference.

16
Network setup. In network setup page, user may set the network for the NVR.
2．User may add and delete IPC; Record Schedule Picture. In this page, user may set recording
time and scheduled recording for the NVR.
3. HDD formatting and overwriting type.

17
2.3 Main Interface
Note: When there is no HDD pre-installed or pre-installed HDD is not formatted, buzzer will be
activated. If you want turn off the buzzer, please go to [AdvancedEventsDisk Full or Disk Error]
to set the buzzer to „Off‟.

18
Chapter 3 NVR Menu
Popup Menu
Component Name
Function
1
Main Menu
Access the main menu
2
Manually Lock Screen
Sign out or access sign-in page
3-5
Four-Channel
Layout/Nine-Channel
Layout/Sixteen-Channel
Layout
Display four channels of video/ Display nine channels of
video/ Display sixteen channels of video
6
More Layout
Displays different channel layout
7
Stream Switch
Switch between Main Stream and Sub Stream
8
View Image Quality
Switch among Realtime, Balanced and Smooth
9
SEQ
Start or stop SEQ
10
Playback
Replay video recorded
11
Record
Enable or disable manual recording
12
Instant Playback
Display channel name Quick playback of video of last 5
minutes
13
Zoom
Hold and drag mouse cursor to select a frame of current
video to zoom in
14
Color
Adjust the color of video
After finishing system initialization, right click the mouse to preview interface or slide the
mouse to the bottom of screen to enter into Pop-up Menu. Now you could perform
parameter setting and operate on Main Menu, Multi-Pics, Record Search, Sequence and
Stream switching.
The options in the pop-up menu may be varied slightly according to different parameter
settings. The options in the menu will be explained in detail in the following chapters.

19
Main Menu Guide
Live
Output
Display
Image control
Privacy Zone
Record
Schedule
Record
Mainstream
Parameter
Switch
Email
Network
RTSP
Motion
Main Menu
Alarm
Record Search
Record Search
Event Search
Device
General
Users
System
Info
Log
Maintain
Advanced
Events
Shutdown
Substream
Mobliestream
DDNS
HDD
Cloud storage
Network
IP Camera
General
DST
NTP
Info
Channel Info

20
3.1 Main Menu
On LIVE mode, click the mouse button, or [Menu] button on the remote controller, or
click [ ] icon on the toolbar to enter the main menu screen.
If system interface is locked, please enter the password to log in. If you forgot your
password, please contact technical support.
In Main Menu mode, you can make adjust the settings for Parameter, Record Search,
Device, System, Advanced and Shutdown.