Samsung SFG-D0100 User manual

Radio Access Network
310 5G Indoor CPE
Installation Manual
Describes the product installation and requirement procedure.
Document Version 1.0
April 2018
Document Number: N/A

© 2018 SAMSUNG Electronics Co., Ltd.
All Rights Reserved. No part of this document may be photocopied, reproduced, stored in a retrieval
system, or transmitted, in any form or by any means whether, electronic, mechanical, or otherwise
without the prior written permission of SAMSUNG Electronics Co., Ltd.
No warranty of accuracy is given concerning the contents of the information contained in this
publication. To the extent permitted by law no liability (including liability to any person by reason of
negligence) will be accepted by SAMSUNG Electronics Co., Ltd., its subsidiaries or employees for
any direct or indirect loss or damage caused by omissions from or inaccuracies in this document.
SAMSUNG Electronics Co., Ltd. reserves the right to change details in this publication without
notice.
This manual should be read and used as a guideline for properly installing and/or operating the
product.
This manual may be changed for system improvement, standardization and other technical
reasons without prior notice.
Updated manuals are available at:
https://systems.samsungwireless.com/
For questions on the manuals or their content, contact
NetSys Tech Write[email protected]amsung.com

Confidential
5G Indoor CPE Installation Manual iii
Copyright © 2018, All Rights Reserved.
Contents
Preface vi
Conventions in this Document........................................................................................................ vi
New and Changed Information ...................................................................................................... vii
Revision History.............................................................................................................................. vii
Organization of This Document ..................................................................................................... vii
Related Documentation ................................................................................................................. vii
Personal and Product Safety ..........................................................................................................viii
Equipment Markings ....................................................................................................................... ix
Chapter 1 Before Installation 1
System View and Interface............................................................................................................... 1
Indoor CPE View........................................................................................................................... 1
Indoor CPE External Interface ...................................................................................................... 2
Indoor CPE Power Cord and Power Supply .................................................................................. 2
Specifications ................................................................................................................................... 4
Cautions for Installation ................................................................................................................... 5
Before Installing........................................................................................................................... 5
While Installing ............................................................................................................................ 5
After Installing ............................................................................................................................. 5
Installation Tools .............................................................................................................................. 6
Chapter 2 Installing System 7
Installation Procedure...................................................................................................................... 7
Transporting and Unpacking ............................................................................................................ 8
Bringing in Items.......................................................................................................................... 8
Unpacking Items .......................................................................................................................... 8
In the Box..................................................................................................................................... 8
Indoor CPE Installation..................................................................................................................... 9
Fixing CPE on Window Sill............................................................................................................ 9
Chapter 3 Inspect the Installation 15
Inspection Plan........................................................................................................................... 15
On-site Inspection and Inspection Checklist............................................................................... 16
Sharing Inspection Results and Taking Corrective Actions ........................................................ 16
Checking the Results of Corrective Actions................................................................................ 16
Sharing the Results of Corrective Actions and Preparing Preventive Plan................................. 16
Construction Situation Checklist ................................................................................................ 16
Appendix A Acronyms 19

Confidential
5G Indoor CPE Installation Manual iv
Copyright © 2018, All Rights Reserved.
List of Figures
Figure 1. CPE DU External Interface ................................................................................................................ 2
Figure 2. Power Cord and Power Supply......................................................................................................... 2
Figure 3. Procedure to Install the Indoor CPE ................................................................................................. 7
Figure 4. Indoor CPE Package Contents .......................................................................................................... 8
Figure 5. Indoor CPE Window Sill Installation Step 1.................................................................................... 10
Figure 6. Indoor CPE Window Sill Installation Step 2.................................................................................... 10
Figure 7. Indoor CPE Window Sill Installation Step 3.................................................................................... 11
Figure 8. Indoor CPE Window Sill Installation Step 4.................................................................................... 11
Figure 9. Indoor CPE Window Sill Installation step 5 .................................................................................... 12
Figure 10. Indoor CPE Window Sill Installation step 6 .................................................................................... 12
Figure 11. Indoor CPE Interface Overview ...................................................................................................... 13
Figure 12. LED Information ............................................................................................................................. 14
Figure 13. Installation Inspection Procedure .................................................................................................. 15
Figure 14. Troubleshooting Steps ................................................................................................................... 18

Confidential
5G Indoor CPE Installation Manual v
Copyright © 2018, All Rights Reserved.
List of Tables
Table 1. 5G Indoor CPE Power Cord and Power Supply Specifications.......................................................... 3
Table 2. 5G Indoor CPE Key Specifications.................................................................................................... 4
Table 3. Basic Installation Tools..................................................................................................................... 6
Table 4. Requirement to Fix Indoor CPE on Window Sill ............................................................................. 12
Table 5. Construction Situation Checklist .................................................................................................... 16

Confidential
5G Indoor CPE Installation Manual vi
Copyright © 2018, All Rights Reserved.
Preface
This manual describes how to install the ICL Indoor CPE (Model: SFG-D0100) on
a window sill including how to connect cables.
Conventions in this Document
Samsung Networks product documentation uses the following conventions.
Symbols
Symbol
Description
Indicates a task.
Indicates a shortcut or an alternative method.
Provides additional information.
Provides information or instructions that you should follow to avoid service
failure or damage to equipment.
Provides information or instructions that you should follow to avoid personal
injury or fatality.
Provides antistatic precautions that you should observe.
Menu Commands
menu | command
This indicates that you must select a command on a menu, where menu is the
name of the menu, and command is the name of the command on that menu.
File Names and Paths
These are indicated by a bold typeface. For example:
Copy filename.txt into the /home/folder1/folder2/bin/ folder.
User Input and Console Screen Output Text
Input and output text is presented in the Courier font. For example,
context <designated epc-context-name>
CLI commands are presented in bold small caps. For example,
Type the RTRV-NE-STS command in the input field.

Confidential
Preface
5G Indoor CPE Installation Manual vii
Copyright © 2018, All Rights Reserved.
New and Changed Information
This section describes information that has been added/ changed since the previous
publication of this manual.
Revision History
The following table lists all versions of this document.
Document Number
Product/Software
Version
Document
Version
Publication Date
Remarks
N/A Indoor ICL 5G
CPE 1.0 April 2018 First version
Organization of This Document
Section
Title
Description
Chapter 1 Before Installation This chapter introduces Indoor 5G CPE description that items
should be understood before installation.
Chapter 2 Connecting
Cables This chapter describes the procedures to connect the cables to the Indoor 5G CPE
Chapter 3 Installing System This chapter describes the procedures to install the Indoor CPE
Chapter 4 Inspect the
Installation This chapter describes the procedures of inspecting installation status after Indoor 5G CPE installation and cabling is completed.
Appendix A Acronyms Describes the acronyms used in this manual.
Appendix B Standard Torque This annex describes the standard torque when tightening the
bolt.
Related Documentation
5G Indoor ICL CPE System Description

Confidential
Preface
5G Indoor CPE Installation Manual viii
Copyright © 2018, All Rights Reserved.
Personal and Product Safety
This product safety information includes European directives, which you must
follow. If these do not apply in your country, please follow similar directives that
do apply in your country.
Proposition 65 (US Only)
State of California Proposition 65 Warning (US only)
WARNING: This product contains chemicals known to the State of California to
cause cancer and birth defects or other reproductive harm.
Electrical
All structural parts are grounded and all input and outputs have built-in isolation
from the network. All input and output ports that connect to external power
sources are designed to meet relevant national safety requirements.
The product contains hazardous energy levels as defined by UL 60950. Care must
be taken when maintaining this equipment as injury to personnel or damage to the
equipment could result from mistakes. Maintenance should only be carried out by
trained and competent engineers who are familiar with the relevant procedures and
instructions.
Manual Handling
Care should be taken when handling equipment. Give due consideration to the
weight of the equipment, the physical capability of the individual(s) handling the
equipment, and movements such as twisting, bending and stooping, which could
lead to skeletal and muscular injuries.
Installation
Installation is recommended to be carried out by trained personnel. All relevant
safety measures should be taken to ensure equipment is not connected to live
power and transmission sources during installation. Equipment must be correctly
installed in order to meet the relevant safety standards and approval conditions.
Maintenance
Maintenance must only be carried out by a suitably trained and competent
technician. All safety instructions must be carefully observed at all times.
Equipment covers should not be removed while live power and transmission is
connected unless in a controlled environment by trained technicians.

Confidential
Preface
5G Indoor CPE Installation Manual ix
Copyright © 2018, All Rights Reserved.
Fire
The product is powered from an AC supply. To protect against fire, the equipment
is fused.
Environment
The product must be operated in an environment with the specified relative
humidity and ambient temperature ranges.
Keep all liquids away from the equipment as accidental spillage can cause severe
damage.
Anti-Static Precautions
The circuit boards and other modules in the product are sensitive to and easily
damaged by static electricity. If any card or sub-assembly is removed from the
unit, the following anti-static precautions must be observed at all times:
•Service personnel must wear anti-static wrist straps.
•Circuit boards and sub-assemblies must be placed on ground conductive mats
or in conductive bags.
•All tools must be discharged to ground before use.
•The anti-static wrist strap and cord must be checked at regular intervals for
their suitability for use.
Equipment Markings
Correct disposal of batteries in this product
(Applicable in countries with separate collection systems.)
The marking on the battery, manual or packaging indicates that the battery in
this product should not be disposed of with other household waste. Where
marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains
mercury, cadmium or lead above the reference levels in EC Directive
2006/66.
The battery incorporated in this product is not user replaceable. For
information on its replacement, please contact your service provider. Do not
attempt to remove the battery or dispose it in a fire. Do not disassemble,
crush, or puncture the battery. If you intend to discard the product, the waste
collection site will take the appropriate measures for the recycling and
treatment of the product, including the battery.

5G Indoor CPE Installation Manual 1
Copyright © 2018, All Rights Reserved.
Chapter 1
Before
Installation
System View and Interface
Indoor CPE View
The view of the Indoor CPE is as follows.

Confidential
5G Indoor CPE Installation Manual 2
Copyright © 2018, All Rights Reserved.
Indoor CPE External Interface
The external interface structure of the Indoor CPE is as follows.
Figure 1. CPE DU External Interface
Factory Reset
nSIM
USB
POWER
LAN
LED(Power)
LED(Signal)
LED(Connection)
LED(Alarm)
Indoor CPE Power Cord and Power Supply
The following figure shows the connectivity of the power cord and power supply.
Figure 2. Power Cord and Power Supply

Confidential
5G Indoor CPE Installation Manual 3
Copyright © 2018, All Rights Reserved.
Table 1. 5G Indoor CPE Power Cord and Power Supply Specifications
Item
Specification
Power Cord Length 1.8 meters
Color Black
Power Supply Input Voltage AC100~240 VAC @ 50/60 Hz
Output Voltage 12 VDC (± 5 %)
Operating Temperature 0~50°C
Operating Humidity 5~90 %

Confidential
5G Indoor CPE Installation Manual 4
Copyright © 2018, All Rights Reserved.
Specifications
Key Specifications
The following table shows the key specifications of the Indoor CPE.
Table 2. 5G Indoor CPE Key Specifications
Item
Specifications
Technology 5G (Follows Verizon 5GTF's latest version)
Operating Frequency 27.5GHz ~ 28.35GHz
Channel Bandwidth 100 MHz
Operating Bandwidth 100MHz x 8 Carrier
Antenna Configuration Integrated Antenna
•Data Channel : 2Tx/2Rx
•RF chain per Data Channel : 32
RF Output Power 36dBm/Path (EIRP, Antenna Gain : 19dBi )
Ethernet Indoor : RJ45 1 Port(100Base-TX or 1000Base-T)
USB USB 2.0 1 Port
USIM Nano-SIM 1 Port
Replaceable regular SIM
LED •Total: 4EA
•Power: Green LED
•Signal: 3 Color(Green/Yellow/Red)
•Connection: 3 Color(Green/Yellow/Red)
•Alarm: 3 Color(Green/Yellow/Red)
Factory Reset •1EA (Push Button Switch)
Operational Temperature 5 ~ 45℃
Humidity 5% ~ 90%, non-condensing,
not to exceed 30g/m^3 absolute humidity
IP rating IP20
EMC FCC Part 15 Subpart B
FCC FCC Part 30 (5G RF)
Installation Indoor: CPE Stand
Warranty Warranty: 1 Year
Volume Indoor: < 1.5L(main Frame, exclude stand)
Weight Indoor: < 1.2 kg (main frame)
Power Supply (selective) AC 100~240 VAC @ 50/60 Hz with External Adapter
Power Consumption Indoor: <20W (Typical)

Confidential
5G Indoor CPE Installation Manual 5
Copyright © 2018, All Rights Reserved.
Cautions for Installation
Observe the following safety instructions when installing the system.
Before Installing
The system must be installed close to a window or wall to face a guided direction
to a 5G signal.
The location of the CPE allows at least 20 cm (about 8 inches) between the unit
and persons to be compliance with FCC RF exposure guidelines.
The location of the CPE is 10 feet away from the products that generate
electromagnetic radiation (e.g. microwave oven).
It is recommended that the product be professionally installed for optimum
performance.
While Installing
•The system power must be cut off before installing.
•Be careful not to damage or scratch on the system and the cables among the
boards when the system is transported or installed.
Make sure the power switch of power supply is off when installing the system.
Installing the system with the power switch on may cause system damage or fatal
human injury when cables are not correctly connected.
Do not wear accessories such as watches and rings in order to prevent electrical
shock.
After Installing
Remove any debris produced during the work and clean up the installation site.
Make sure that worker does not damage installed cables while cleaning the system.
While cleaning the power supply device, take caution that the device does not
come in contact with foreign objects that may cause power failure.

Confidential
5G Indoor CPE Installation Manual 6
Copyright © 2018, All Rights Reserved.
Installation Tools
The basic tools for installation are listed in the table below. The additional tools
required for each site need to be identified and prepared during a site survey before
starting installation.
Table 3. Basic Installation Tools
No.
Name
Specification
Remarks
1
Basic tool 3M Dual lock

5G Indoor CPE Installation Manual 7
Copyright © 2018, All Rights Reserved.
Chapter 2
Installing System
This chapter describes the procedures to install the system.
Installation Procedure
The procedure to install the RFA is as follows.
Figure 3. Procedure to Install the Indoor CPE
Fixing Window Sill
Power Up the indoor CPE
Plug in the Power to CPE
Ethernet cable into LAN port of CPE
Fixing indoor CPE on window sill

Confidential
5G Indoor CPE Installation Manual 8
Copyright © 2018, All Rights Reserved.
Transporting and Unpacking
This section describes the work to unpack cabinets and other components and
transport them to the location to be installed.
Bringing in Items
Bring in items, taking care of the following:
•When carrying the system, tighten the system firmly: do not exceed the proper
vibration level from 1 to 500 Hz.
•While moving the system, the system should not be shocked physically or
damaged caused by dust, moisture, and static electricity.
Unpacking Items
The procedure to unpack items is as follows:
•The packing items must be packed until they reach the installation place.
•The items are classified in accordance with each job specification and stored
on a place that does not interfere with working.
•Unpack only external packing, leaving the internal packing in unpacked status.
•Unpack the inner packaging after each system is placed on its installation
location.
•Scrap by-products (packaging waste) in accordance with the rule. Do not
recycle the by-products.
In the Box
Figure 4. Indoor CPE Package Contents

Confidential
5G Indoor CPE Installation Manual 9
Copyright © 2018, All Rights Reserved.
Indoor CPE Installation
This section describes the procedures to fix the indoor CPE on a window sill.
There are other mounting methods that may be available for installation. However,
the main objective is that the unit shall be firmly mounted.
The Indoor CPE bottom shows the proper orientation of the CPE side facing
outside the window. Make sure to check the correct orientation while installing.
The Indoor CPE must be fixed vertically as depicted in the following guidelines.
Fixing CPE on Window Sill
For the installation directions and fixing method, see the following images.
The indoor CPE installation on a window sill is a convenient and quick method to
install the CPE with good RSRP measurement conducted as a pre-qualification
with Spectrum analyzer.
To install the CPE on a window sill:
1 Locate the CPE fixing point on the window sill and make sure the surface is
free of dust and debris.
2 Unwrap and attach the 3M dual lock on the base of the window sill and to the
bottom part of the CPE as depicted in the figures below.
3 Make sure to check the direction mark at the bottom of the CPE stand as
shown in the figure below.
4 Make sure the CPE is firmly positioned on the window sill with 3M dual lock.

Confidential
5G Indoor CPE Installation Manual 10
Copyright © 2018, All Rights Reserved.
Figure 5. Indoor CPE Window Sill Installation Step 1
Figure 6. Indoor CPE Window Sill Installation Step 2

Confidential
5G Indoor CPE Installation Manual 11
Copyright © 2018, All Rights Reserved.
Figure 7. Indoor CPE Window Sill Installation Step 3
Figure 8. Indoor CPE Window Sill Installation Step 4