Santec TH-5034 User manual

SLEEVE
VALVE
BODY
PROJECTION ON
THE SLEEVE
GROOVE ON THE
VAL VE BODY
CENTER MARK
110111111000
10011100000090999000
110111111000
10011100000090999000
Temperature Dial
Numerical Dial
Mounting Screw
110111111000
10011100000090999000
Temperature Dial
Numerical Dial
Mounting Screw
110111111000
10011100000090999000
Set Screw
TH-5034 (3/4” THERMAX THERMOSTATIC VALVE AND TRIM)
When sleeve is fully on the valve body
temperature limiter will go to the stem
aligning the mark on the limiter to the mark
on the sleeve and body.
Put on the plate aligned to the wall and screw in
the plate mounting screws.
Put on the thermostatic dial on the valve stem.
Match 100 mark with the center mark on the sleeve
to adjust the temperature at lowest level.
INSERT THE NUMERICAL DIAL MOUNTING SCREW THROUGH THE
COAXIAL HOLE IN THE TEMPERATURE DIAL STEM.
Plate Mounting Screws
WallWall
WallWall
PUT ON THE HANDLE ON THE STEM AND SCREW
IN THE SET SCREW BY THE PROVIDED ALLEN KEY.
Align the projection on the
sleeve with projection on the top
lip of the body and then slide
it on the valve body.
SLEEVE IS ON THE
VALVE BODY FULLY
12
4 5
Allen key
Page 1
00TH-AA *00TH-AC * 00TH-BF * 00TH-CA *00TH-CC *
00TH-CD * 00TH-CN * 00TH-CV * 00TH-DD * 00TH-DV *
00TH-ER * 00TH-FF * 00TH-HH * SAME AS TL *PH-1111 -1 *
00TH-LC * 00TH-LL *00TH-LM * 00TH-LS * 00TH-LV *
00TH-ML *00TH-MX * 00TH-NC * 00TH-NL *00TH-NX *
00TH-RE * 00TH-RP * 00TH-RX * 00TH-SL *
00TH-TT *00TH-VL *00TH-VX * 00TH-WE * 00TH-WG *
00TH-XL *00TH-XA *
HANDLETRIM
AA AC BF CA CC
CD CN CV DD DV
ER FF HH JC LA
LC LL LM LS LV
MLMXNCNLNX
RERPRXSL
TTVLVXWEWG
XLXA
10511100055510011100000095999555
10511100055510011100000095999555
10511100055510011100000095999555
10511100055510011100000095999555
10511100055510011100000095999555
10511100055510011100000095999555
1051110005551001110000009599955510511100055510011100000095999555
10511100055510011100000095999555
10511100055510011100000095999555
10511100055510011100000095999555
10511100055510011100000095999555
10511100055510011100000095999555
10511100055510011100000095999555
10511100055510011100000095999555
10511100055510011100000095999555
10511100055510011100000095999555
10511100055510011100000095999555
10511100055510011100000095999555
10511100055510011100000095999555
10511100055510011100000095999555
10511100055510011100000095999555
10511100055510011100000095999555
10511100055510011100000095999555
10511100055510011100000095999555
1 0 5111 00055510011100000095999555
1 05111 00055510 0111000000959995551 05111 00055510011100000095999555
1 0511100055510011100000095999555
10511100055510011100000095999555
10511100055510011100000095999555
10511100055510011100000095999555
10511100055510011100000095999555
1 05111 0005551 00111 0000009 5999 555
1 0 5111 000 55510 0111000 00095999555
1 05111 00055510011100000095999555
1 05111000555100111000 00095999555
00TH-NX *
10511100055510011100000095999555
TL
10511100055510011100000095999555
00YY-TD 00YY-TX
TD TX
10511100055510011100000095999555
10511100055510011100000095999555
TEMPERATURE
LIMITER
WallWall
3
INSTALLATION INSTRUCTIONS
Top View

110110
1001009090
Thermostatic
Extension
ExtensionScrew
110111111000
10011100000090999000
110111111000
10011100000090999000
To drive in the extension screw
you need to have a thin width
screw driver which can go in the
blind hole of the dial gauge.
110111111000
10011100000090999000
Set Screw
WallWall
WallWall
WallWall
Plate Mounting Screws
TH-5034 (3/4” THERMAX THERMOSTATIC VALVE AND TRIM WITH OPTIONAL EXTENSION)
PUT ON THE THERMOSTATIC EXTENSION ON THE
STEM OF THE VALVE. FULLY SLIDE IT IN.
PUT ON THE THERMOSTATIC PLATE ON
THE WALL, AND PUT ON THE MOUNTING
SCREWS. AFTER THAT PUT ON THE
TEMPERATURE DIAL ON IT.
Insert long extension screw through the coaxial hole in the temperature
dial. A long thin screw driver would be needed to firmly tighten this screw.
This screw will hold the extension and the temperature dial.
After putting on long extension screw, temperature dial and plate
with mounting screws assembly looks like this.
Put on the handle on the stem. Put on the set screw on the
base of the handle. Firmly tighten the set screw.
Assembly looks like this.
Thermostatic
Plate
Sleeve
INSTALLATION INSTRUCTIONS
XXXX
9.75”
6.75”
THERMA TTTHHHEEERRRMMMAAA
Santec Inc.
3501 Challenger Street, Torrance, CA 90503
Tel: [phone] Fax [phone]
Www.santecfaucet.com
SANTEC
THERMOSTATIC PLATE
SANTEC
THERMOSTATIC PLATE
WallWall
1 2
3 4
5
Page 2
Take temperature
limiter out
Put back temperature limiter
through the extension stem