Santec PB-3950 User manual

(NEW 2010)

PRESSURE BALANCED SHOWER VALVE (PB-3950)
INSTALLATION AND ROUGH-IN
MECH ANIC AL STOP
STOP POST
Illustration D1
Illustration D2
MECH ANIC AL STOP
STOP POST
LIMIT STOP
LIMIT STOP
PAGE 03
TEMPERATURE LIMIT STOP SET UP
Santec Pressure Balanced Valve has a temperature limit stop ( please
see Illustration C) which once set properly can provide a safe and
comfortable hot water. Below is the limit stop installation procedure:
- Remove all Handle trim parts, including the trimplate.
- Remove all internal parts up to the Limit Stop, do not remove the
Mechanical Stop.
If Mechanical Stop is removed please follow the instruction below:
- Turn the cartridge clockwise until it is stopped. Do not force
to avoid damaging the cartridge.
- Insert the Mechanical Stop onto the catridge.
- Turn the cartridge counterclockwise to open the water line. Turn
until it reaches the maximum hot water desired by the user.
- Place Limit Stop as shown in the Illustration D2.
- Reinstall all the parts accordingly to the Illustration C.
6
34
2
11
5
8
7
9
1
10
New
New
New
New
New
PB-3950
Pessured Balanced w/ Diverter (Valid after Jan 2010)
12
13
PM-8 Kit Extension, 20K Broach
PM-9 Kit Extension, 16K Broach
PM-113X DIverter Extension
ITEM
NO.
PART NUMBER DESCRIPTION QTY.
1 TE025 (prior to Jan 2010 - TE010) Cartridge 1
2
TE-015 Valve Cover 1
3
TE013 Limit Stop 1
4
TE014 Limit Stop 1
5
TE011 Screw 4
6
PM-963 (prior to Jan 2010 - PM-009) Brass Lock Plate 1
7
PM-964 (new) Mud Guard Holder 1
8
PB-3950-4 Screw 2
9
Mud Guard (not a spare part) Mud Guard 1
10
Valve Body (not a spare part) Valve Body 1
11
Diverter Body (not a spare part) Diverter Body 1
12
PM-1092 Extension 1
13
PB-002/TE060/TE050 (see picture
below
Diverter Cartridge 1
13
TE050 TE060
PB-002

PAGE 04
PRESSURE BALANCED TUB/SHOWER VALVE (PB-3950)
INSTALLATION AND ROUGH-IN
TROUBLE SHOOTING
NOTE: AT NO TIME TRY TO STOP DRIPPING BY APPLYING EXTREME FORCE WHEN CLOSING THE VALVE.
MALFUNCTION CAUSE REMEDY
Shower control opening
through hot.
Tub ller or Shower head
drips after shutting o the
valve.
Shower insuciently hot.
No ow of hot or cold water.
Valve body too deep in the
wall.
Hot and cold water supplies have
been connected in reverse
Water remains in the piping column
to the shower head (this is normal).
Incorrect setting of the mechanical
stop against the stop post causing
a partially opened cartridge.
O-ring seal on the inlet of the
cartridge is faulty.
Adjustable handle position stop
incorrectly set.
Either the hot or cold side is not fully
pressurized.
Debris caught inside the inlet of the
The measured rough-in or nished wall
surface is incorrect.
cartridge.
Rotate cartridge
Allow approximately 3-5 minutes to
drain column.
Reset the mechanical stop as described
in the page 3
Check O-ring for cuts or damage and
replace if necessary.
Check the hot water source temperature
setting.
Be sure service stops (when applicable) are
both wide open and system is fully pressurized.
Remove cartridge and ush out or remove
Install the extension kit.
PM-8 (20K Broach Extension Kit)
PM-9 (16K Broach Extension Kit)
PM-113X (Diverter Extension)
any debris lodged inside the hot or cold
inlets
Santec Inc.
3501 Challenger Street, Torrance, CA 90503
Tel: [phone] Fax [phone]
www.santecfaucet.com 01/10