Sanus VLT5 User manual

Scan for easy
install video
THANK YOU FOR CHOOSING SANUS
THE #1 TV MOUNT BRAND IN THE US.
MERCI D'AVOIR CHOISI SANUS
LE N ° 1 DE MARQUE TV de montage dans les États-Unis.
Balayez ce code pour
visionner une vidéo
d’installation facile
VLT 5 Instruction Manual

SANUS MAGNETIC STUD FINDER Designed to find your studs and make life easier – included in hardware kit.
TWO SIMPLE STEPS TO FINDING YOUR STUDS:
Step 1 / Étape 1
Step 2 / Étape 2
WARNING: This product contains a magnet. If an implanted medical device such as a pacemaker or implantable cardioverter defibrillator (ICD) is in use, magnetic fields may affect the operation of those devices, resulting in
serious injury or death. If you have an implanted medical device, keep at least 13 cm (5in.) between your device and the magnet. Please consult with your physician or medical professional prior to using this product.V
LOCALISATEUR DE MONTANTS
MAGNÉTIQUE
SANUS
Conçu pour trouver les montants et vous faciliter la vie. Inclus dans la trousse de quincaillerie.
magnet
locates screws in drywall
to show exactly where
your studs are
probing pin
helps find the edges of
your stud within the wall
level
attaches to your wall plate
for hands free leveling
aimant
localise les vis dans les cloisons
sèches pour indiquer l'emplace-
ment exact des montants
niveau
s'attache à votre plaque
murale pour une mise de
niveau mains libres
tige de sondage
vous aide à trouver les bords
des montants dans le mur
LOCALISEZ LES MONTANTS EN DEUX SIMPLES ÉTAPES :
Holding it vertically, lightly move the SANUS Magnetic Stud Finder up
and down while sliding across your wall. The magnet within will be
attracted to the screws in the stud.
Once the magnet has landed on a screw, place a pencil mark on the
wall directly below the magnet.
You can verify this is a stud by moving the Magnetic Stud Finder up or
down to find a second or third screw within the wall.
Placez le localisateur de montants magnétique SANUS en position verticale sur le
mur et faites-le glisser légèrement vers le haut et le bas. L'aimant situé à l'intérieur
sera attiré par les vis dans le montant.
Dès que l'aimant détecte une vis, marquez l'emplacement au crayon sur le mur,
directement sous l'aimant.
Vous pouvez vérifier que cela indique eectivement la présence d'un montant en
déplaçant le localisateur de montants magnétique vers le haut ou le bas pour
trouver une deuxième ou une troisième vis dans le mur.
Ouvrez le localisateur de montants magnétique SANUS pour exposer la tige de
sondage contenue à l'intérieur. Pour trouver les bords du montant, démarrez à
1/2 po (13 mm) de la première marque au crayon et insérez la tige de sondage
dans le mur tous les 1/8 po (3 mm) jusqu'à ce qu'elle rentre entièrement dans
le mur. Répétez cette opération jusqu'à ce que vous ayez localisé les deux
bords et le centre.
Pull apart the SANUS Magnetic Stud Finder to expose the probing pin
within. Starting about 1/2 inch away from the first pencil mark insert
the probing pin into the wall every 1/8 inch until it inserts completely
into the wall. Once that happens, you know you've found one edge of
your stud. Repeat this process till you have found the stud edges and
center of the stud.
AVERTISSEMENT: Ce produit contient un aimant. Si un dispositif médical implanté comme un stimulateur cardiaque ou un défibrillateur cardioverteur implantable (DCI) est utilisé, le champ magnétique peut affecter le
fonctionnement de ces appareils et peut entraîner des blessures graves ou la mort. Si vous avez un dispositif médical implanté, conservez une distance de 13cm (5po) entre votre dispositif et l'aimant. Veuillez consulter votre médecin ou un
professionnel de la santé avant d'utiliser ce produit.

3
VLT5
We’ll Make It Stress-Free
If you have any questions along the way, just give us a call.
1-800-359-5520 (UK: 0800-056-2853) We’re ready to help!
Nous vous faciliterons la tâche, sans casse-tête
Si vous avez des questions en cours de route, appelez-nous.
Composez le 1-800-359-5520 (Royaume-Uni: 0800-056-2853)
Nous sommes là pour vous aider!

4
125 lb
(56.7 kg)
IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS – PLEASE READ ENTIRE MANUAL PRIOR TO USE
Before getting started, let’s make sure this mount is perfect for you!
No — Perfect!
Yes — This mount is NOT compatible. Visit MountFinder.Sanus.com or call
1-800-359-5520 (UK: 0800-056-2853) to find a compatible mount.
Please read through these instructions completely to be sure you’re comfortable with this easy install process.
Also check your TV owner’s manual to see if there are any special requirements for mounting your TV.
If you do not understand these instructions or have doubts about the safety of the installation, assembly or use
of this product, contact Customer Service at 1-800-359-5520 (UK: 0800-056-2853).
Do you have
all the tools
needed?
1
2
3
4
What is your
wall made of? Drywall
with steel
studs?
Unsure?
Drywall
with wood
studs?
Solid concrete
or concrete
block?
CAUTION: Avoid potential personal injuries and property damage!
●This product includes directions and hardware for use with wood stud, solid concrete and concrete block walls –
DO NOT install into drywall alone. For information on how to use this product with steel stud walls contact Customer
Service and ask about the SSMK1 steel stud mounting kit.
●The wall must be capable of supporting five times the weight of the TV and mount combined.
●Do not use this product for any purpose not explicitly specified by manufacturer.
●Manufacturer is not responsible for damage or injury caused by incorrect assembly or use.
Call Customer Service: 1-800-359-5520 (UK: 0800-056-2853)
Perfect! Perfect!
Ready to
begin?
Steel stud kit (#SSMK1) required
7/32 in.
(5.5 mm)
Wood
Screwdriver Tape Measure Drill Bit Drill Bit Electric Drill Hammer Socket Wrench
3/8 in.
(10 mm)
Concrete
Does your TV weigh
more than 125 lb
(56.7 kg) including
accessories?
1/2 in.
(13 mm)

5
STEP 1 Attach Bracket to TV
NOTE: Not all hardware included will be used.
WARNING: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged
item to your dealer; contact Customer Service. Never use damaged parts!
Parts and Hardware for STEP 1
Right TV
Bracket
Left TV
Bracket 02 x1
01 x1 Spacer
M4x35 mm
M5x35 mm
M6x35 mm
M8x35 mm
04
06
07
x4
x4
x4
03
05 08 09
x4 x4
x4
x4
TV Screws
TV Washers
Spacers
M8x45 mm
10 x4

6
1-1 Select TV Screws
Hand thread screws into the threaded inserts on the back of your TV
to determine which screw diameter (M4, M5, M6, or M8) to use.
1-2 Spacers
M4 M6 M8M5
Spacers and screws are supplied to install your TV bracket.
Determine your preference for spacer configuration when
attaching your TV bracket.
Mount the spacers 10
above the TV bracket,
so the TV bracket sits
close to the TV surface
for flat back panels.
TV Bracket
TV Bracket
Mount the spacers 10
under the TV bracket to
create extra space needed
for irregular shape TV
backs or large cables.
10
10
Round Back CablesInset HolesFlat Back
ab
CAUTION: Verify adequate thread engagment of the screw/
spacer combination on your TV.
Too short will not hold the TV and too long will damage the TV.
Too Short Correct Too Long

7
IMPORTANT: For
ease of access, straps
should be level with
the bottom of the TV.
1-3 Attach TV Brackets
Center the TV brackets 01 and 02 over your TV hole pattern as shown - making sure the brackets are level.
NOTE: The tilt tension knob Ton TV brackets 01 and 02 should be oriented to the outside edges.
Install using the spacer, screw and washer combination you selected for your TV.
aSpacer, screw and washer
bSpacer, screw and washer
10
10
08
08
09
09
03
03
04
04
05
05
06
06
07
07
0201
If your TV included inset spacers or wall mount adapters,
see Troubleshooting on PAGES 22-23.
T
Standard configurations are shown.
For special applications, or if you
are uncertain about your hardware
selection, contact Customer Service
at 1-800-359-5520 .
T

8
STEP 2 Attach Wall Plate to Wall
For wood stud installations, follow STEP 2A on PAGE 9
For concrete installations, follow STEP 2B on PAGE 14
*WARNING:This product contains a magnet. If an implanted medical device such as a pacemaker or implantable cardioverter defibrillator
(ICD) is in use, magnetic fields may aect the operation of those devices, resulting in serious injury or death. If you have an implanted medical device,
keep at least 13 cm (5 in.) between your device and the magnet. Please consult with your physician or medical professional prior to using this product.
5⁄16 in. x 2 3⁄4 in.
* Sanus Magnetic Stud Finder
14 x4
11 x1
12 x1
13 x1
15 x4
Parts and Hardware for STEP 2
WARNING: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged
item to your dealer; contact Customer Service. Never use damaged parts!
Wall Plate
Wall Plate
Template Lag Bolt
Concrete Anchor
NOTE: Not all hardware included will be used.

9
STEP 2A Wood Stud Option
2
3
CAUTION: Avoid potential personal injuries and
property damage!
●Drywall covering the wall must not exceed
5/8 in. (16 mm)
●Minimum wood stud size: common 2 x 4 in.
(51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm)
●Minimum horizontal space between fasteners:
16 in. (406 mm)
●Stud centers must be verified – not all walls have
conventional 16 in. (406 mm) or 24 in. (610 mm)
stud spacing
1. Locate a nail/screw in the studs using the Sanus
magnetic stud finder 13 provided.
2. Find the edges of the studs using the probe
of the stud finder 13 .
3. Mark the centers of the studs with pencil.
13
1
Min. 16 in.
(406 mm)
Max. 5/8 in.
(16 mm)
Min. 3 1/2 in.
(89 mm)
Min. 1 1/2 in.
(38 mm)

10
4. Place the wall plate template 11 at your desired height and position the slotted holes over your stud center lines. Level the wall plate
template 11 and tape in place.
NOTE: For assistance in determining wall plate location, see HeightFinder at sanus.com.
IMPORTANT: Be sure you mark and drill into the center of the stud.
5. Drill the four pilot holes using a 7/32 in. (5.5 mm) diameter drill bit.
IMPORTANT: Pilot holes must be drilled to a depth of 3 in. (75 mm).
1111
13
4 5
3 in. (75 mm)
7/32 in.
(5.5 mm)

11
6. Partially install the top two lag bolts 14 ,leaving about 1/2 in. (13 mm) space from the wall.
NOTE: This space allows you to remove the wall plate template 11 and hang the wall plate 12 onto the top lag bolts 14 .
7. Remove the wall plate template 11 .
1111
14
6 7
≈ 1/2 in.
(13 mm)

12
8. Slide the covers Copen on the wall plate 12 to expose the mounting holes.
9. Hang the wall plate 12 on the top lag bolts 14 .
1412
C
C
12
89

13
10. Install the bottom two lag bolts 14 . Firmly tighten all four lag bolts 14 until they are pulled flush against the wall plate 12 .
NOTE: Hold the wall plate 12 in place when tightening the first lag bolt 14 to keep the plate from shifting out of place.
CAUTION: Avoid potential personal injury or property damage! All four lag bolts 14 MUST BE firmly tightened to prevent unwanted
movement of the wall plate 12 .Ensure the wall plate is securely fastened to the wall before continuing on to the next step.
11. Slide the covers Cclosed on wall plate 12 .
Go to STEP 3 on PAGE 18.
14
12
10
12
C
C
11

14
STEP 2B Solid Concrete or Concrete Block Option
CAUTION: Avoid potential personal injuries and property damage!
●Mount the wall plate 12 directly onto the concrete surface
●Minimum solid concrete thickness: 8 in. (203 mm)
●Minimum concrete block size: 8 x 8x 16 in. (203 x 203 x 406 mm)
●Minimum horizontal space between fasteners: 24 in. (610 mm)
1. Position the wall plate template 11 on the wall at your desired height. Level the wall plate template and mark the hole locations.
NOTE: For assistance in determining wall plate location, see Height Finder at sanus.com.
2. Drill four pilot holes using a 3/8 in. (10 mm) diameter drill bit.
IMPORTANT: Pilot holes must be drilled to a depth of 3 in. (75 mm). Never drill into the mortar between blocks.
11
11
13
12
3/8 in.
(10 mm)
3 in. (75 mm)
Min.
24 in.
(610 mm)

15
3. Remove the wall plate template 11 and insert four anchors 15 .
CAUTION: Be sure the anchors 15 are seated flush with the concrete surface.
4. Partially install the top two lag bolts 14 , leaving about 1/2 in. (13 mm) space from the wall.
NOTE: This space allows you to hang the wall plate 12 onto the top lag bolts 14 .
1415
11
3 4 ≈ 1/2 in.
(13 mm)

16
5. Slide the covers Copen on the wall plate 12 to expose the mounting holes.
6. Hang the wall plate 12 on the top lag bolts 14 .
141212
C
C
6
5

17
12
7. Install the bottom two lag bolts 14 . Firmly tighten all four lag bolts 14 until they are pulled flush against the wall plate 12 .
NOTE: Hold the wall plate 12 in place when tightening the first lag bolt 14 to keep the plate from shifting out of place.
CAUTION: Avoid potential personal injury or property damage! All four lag bolts 14 MUST BE firmly tightened to prevent unwanted
movement of the wall plate 12 .Ensure the wall plate is securely fastened to the wall before continuing on to the next step.
8. Slide the covers Cclosed on wall plate 12 .
14
7
12
C
C
8

18
HEAVY! You may need assistance with this step.
STEP 3 Attach TV to Wall Plate
1. Hook the TV brackets 01 and 02 onto the wall plate 12 .
NOTE: The TV brackets 01 and 02 can be slid anywhere along the wall plate 12 for optimal positioning of your TV.
2. Rest the TV into place against the wall.
3. Press the bottom of the TV into the wall plate 12 until the latches lock the TV in place.
CAUTION: Avoid potential personal injury or property damage! Always make sure your TV brackets are in the locked position so the
TV is securely fastened to the wall plate 12 .
01
02 12
12
0201
1 2 3

19
Manage Cables
Tilt the TV up or down to gain access to the back of the TV.
Attach your cables, then adjust the TV as desired.
Cables

20
Adjustments
LEVEL Tilt
To level your TV, turn the level
adjustment screw Son the top of
either TV bracket 01 or 02 to raise or
lower that respective side of the TV.
Your TV should adjust easily when moved,
then stay in place.
Adjust the tilt tension knob Tif your TV
naturally tilts up or down.
NOTE: If you do not intend to adjust the
tilt for different viewing locations, you can
tighten the tilt tension knobs Tto prevent
unwanted movement.
Raise
Lower
01
02
Tighten
Loosen
S
T