Sanyo VDC-D1185VP User manual

INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
MANUEL D’INSTRUCTIONS
VDC-D1185VP
VDC-D2185VP
COLOUR CCD camera
CCD-Farbkamera
Caméra CCD COULEUR
CCD
VDC-D1185VP (SURFACE TYPE) VDC-D2185VP (IN-CEILING TYPE)
About this manual
Before installing and using the camera, please read this manual
carefully. Be sure to keep it handy for later reference.
Über diese Bedienungsanleitung
Lesen Sie bitte vor der Montage und dem Inbetriebnehmen der
Kamera zuerst diese Bedienungsanleitung sorgfältig durch und
bewahren Sie sie zum späteren Nachschlagen auf.
A propos de ce manuel
Avant d’installer et d’utiliser la caméra, veuillez lire ce
manuel attentivement. Gardez-le à portée de main pour
toute référence ultérieure.
L5AK4/XE, L5AL4/XE GB 2003, 6, 5

Depending on the conditions of use, installation and environment,
please be sure to make the appropriate settings and adjustments.
If you need help with installation and/or settings, please consult your
dealer.
CONTENTS
PRECAUTIONS........................................................................................ 2
INSTALLATION....................................................................................... 3
SETTINGS ............................................................................................... 5
ADJUSTMENT ........................................................................................ 10
TROUBLESHOOTING ............................................................................. 11
SPECIFICATIONS.................................................................................... 12
ACCESSORIES
VDC-D1185VP
•Hexagonal rench (Big)........................................................... 1 pc.
•Hexagonal rench (Small) ....................................................... 1 pc.
•Cushioning sheet...................................................................... 1 pc.
•Ferrite core ............................................................................... 2 pc.
VDC-D2185VP
•Hexagonal rench (Big)........................................................... 1 pc.
•Cushioning sheet...................................................................... 1 pc.
•Ferrite core ............................................................................... 2 pc.
FEATURES
•The optical filter is switched automatically to colour image or black
and white image according to the subject brightness.
•Built-in interline transfer method 1/4" CCD, approx. 470,000
picture elements.
•Equipped with a DSP (Digital Signal Processor).
•Horizontal resolution, more than 520 TV lines.
•High sensitivity, minimum required illumination is 0.06 lux (F1.4
B/ mode).
•Two types of backlight compensation functions (multi-spot
photometry and centre-focus photometry).
•Dual power supply 12 – 15 V DC or 24 V AC.
L5AK4/XE, L5AL4/XE GB 2003, 6, 5
English 1

PRECAUTIONS
In case of malfunct on
Do not use the camera if smoke or a strange odour comes from the
unit, or if it seems not to function correctly. Disconnect the power
supply immediately, and consult your dealer (or a Sanyo Authorized
Service Centre).
Do not open or mod fy
Do not open the cabinet, as it may be dangerous and cause damage
to the unit. For internal settings and repairs, consult your dealer (or a
Sanyo Authorized Service Centre).
Do not put objects ns de the un t
Make sure that no metal objects or flammable substances get inside
the camera. If used with a foreign object inside, it could cause a fire,
short-circuit or damage.
If water or a liquid gets inside the camera, disconnect the power
supply immediately, and consult your dealer (or a Sanyo Authorized
Service Centre). Be careful to protect the camera from sea water, etc.
Be careful when handl ng the un t
To prevent damage, do not drop the camera or subject it to strong
shock or vibration.
Install away from electr c or magnet c f elds
If installed close to a TV, radio transmitter, magnet, electric motor,
transformer, or audio speakers the magnetic field they generate will
distort the image.
Protect from hum d ty
To prevent damage to the camera, do not install it where there is
greasy smoke or steam or where the dampness may get too high.
Protect from h gh temperatures
Do not install close to stoves, or other heat generating devices, such
as spotlights, etc., or where it could be subject to direct sunlight, as
that could cause deformation, discoloration or other damage.
Be careful when installing close to the ceiling, in a kitchen or boiler
room, as the temperature may rise to high levels.
Install where the temperature range will stay between –10°C and
50°C. (no condensation)
Clean ng
Dirt can be removed from the housing by wiping it with a soft cloth.
To remove stains, wipe with a soft cloth moistened with a soft
detergent solution and wrung dry, then wipe dry with a dry soft cloth.
Do not use benzine, thinners or other chemical products on the
housing, as they may cause deformation and paint peeling. Before
using a chemical cloth, make sure to read all accompanying
instructions. Make sure that no plastic or rubber material comes into
contact with the housing for a long period of time, as that may cause
damage or paint peeling.
Mount ng Surface
The mounting surface material must be strong enough to secure the
camera. Plaster- board without a backing plate is not recommended.
ENGLISH
L5AK4/XE, L5AL4/XE GB 2003, 6, 5
2 English

INSTALLATION
Note: hen setting up this camera, make sure that it is installed securely. If it
is not installed correctly, it may fall down. In addition, do not touch the
camera in places except where settings and adjustments are necessary.
Coax al cable type and max mum length
•Cable type RG-59U (3C-2V), 250 m maximum.
•Cable type RG-6U (5C-2V), 500 m maximum.
•Cable type RG-11U (7C-2V), 600 m maximum.
Install ng the Model VDC-D1185VP
1Use the supplied hexagonal wrench to remove the four fixing
screws (B) of dome cover (A).
2Make screw holes and a cable hole in the cushioning sheet (D)
that attaches to the back of the camera unit (C).
3Attach the cushioning sheet (double-sided tape) to the back of the
camera unit.
4Align the camera unit with the surface of the ceiling, make marks
on the ceiling in the places where the screw holes are to be drilled,
and then drill the four holes.
5Cut a hole in the ceiling for routing the cables.
Note: hen routing the cables in the ceiling, use the accessory hexagonal
wrench (small) to loosen the cable cover fixing screw (E) at the rear
of the unit, and then remove the cable cover screw (F).
The follow ng step d ffers only when nstall ng the Model
VDC-D2185VP
Make a cable hole with a diameter of 73 mm.
73mm
(A)
(B)
(H) (G)
(K)
(D)
(C)
(Model VDC-D1185VP) (Model VDC-D2185VP)
(J)
(I)
(H) (G)
(C)
(D)
(E)
(F)
L5AK4/XE, L5AL4/XE GB 2003, 6, 5
English 3

INSTALLATION
6Pass the power cable/day-night cable (G) and video cable (H)
from the camera unit through the cable hole in the ceiling.
(Power cable/day-n ght cable)
7Align the four screw holes in the camera unit (C) with the screw
holes in the ceiling, and then secure the camera in place by
tightening the screws.
8Carry out the settings and adjustments for the camera.
Refer to p. 5 for camera settings and adjustments, and to p. 10
for lens adjustments.
9If the dome liner is secured in place, loosen the screw (I).
Adjust the dome liner (J) so that the dome camera’s lens is visible
from the camera window (K), and then use a hexagon wrench to
fix the dome cover.
Connect ons
Note: hen connecting the video cable of this unit to a TV monitor,
the accessory ferrite core (two winds) must be installed to the
video cable in order to prevent electromagnetic interference
with the other connected devices.
RED
Cable
BLACK
WHITE
YELLOW
PURPLE
GND
COLOR
B/W
+~
~
–
DC12 AC24
Power cable
Day/n ght
cable
AC 24 V connect on
DC 12 V connect on
1
1RED
Cable
BLACK
WHITE GND
2
3
23
+
+~
~
–
–
~~
GND
DC12 AC24
L5AK4/XE, L5AL4/XE GB 2003, 6, 5
4 English

SETTINGS
hen changing the settings and adjustments for this camera, loosen the camera unit screw (A) and remove the lens unit in the direction of the
arrow. hen changing the DIP switch settings, take care when making the settings and adjustments because power is still being supplied to the
camera.
Control name Pos t on
1Colour and Black/Wh te level sw tch (C/B)
(Normal: LOW/H gh sens t v ty: HI) LOW
23 H gh speed electron c shutter sett ng (ES) 1/50 sec.
4Aperture compensat on sett ng (AP)
(Sharp: SHRP/Normal: NORM) SHRP
5Backl ght compensat on sett ng (BL-M)
(ON (MULT)/OFF) OFF
6Backl ght compensat on sett ng (BL-C)
(ON (CENT)/OFF) OFF
7Wh te balance sw tch (WB) and colour
(R or B) adjustment volume ATW
8Synchron zat on sett ng (SYNC)(LL/INT) INT
9L ne phase adjustment (PHASE) adjustable
FLens r s level adjustment adjustable
(A)
1 2 3 4 5 6 7 8
HI
C/B ES AP BL-M BL-C WB SYNC
1 2 SHRP ON ON MANU LL
LOW OFF OFF NORM OFF OFF ATW INT
F
VR121
7
1
ON
234 5678
9
The illustration shows the factory default settings for the switches in the camera setup section.
L5AK4/XE, L5AL4/XE GB 2003, 6, 5
English 5

SETTINGS
C •
••
• B/W (colour/black and wh te) sw tch sett ng
This switch lets you select the timing of the automatic switching of
the optical filter to colour image or black and white image, according
to the subject brightness. The default setting is down (LOW). Set the
switch according to the brightness.
(F g. 1)
H: for a brighter setting than LOW
L: Standard setting
Notes:
•After the power has been turned off, switching will restart from
colour, when the power is restored.
•A sound may be heard when the colour image or black and white
image is switched. Also, the image will be distorted as shown in
F g. 1, this is normal and does not indicate a problem.
•hen using infrared lighting, if there is a strong reflection on the
subject, the optical filter may switch from black and white to
colour mode. Use only enough infrared lighting so that the mode
is not switched.
•The focus setting may be different in black and white mode and
colour mode. Please check the focus setting in both modes.
H gh speed electron c shutter sett ng
Normally, the speed setting switches for the high speed electronic
shutter are all set to the down (OFF) position. This sets the electronic
shutter (ES 1, 2) speed to 1/50 sec. The switches can be set as
indicated in table A to select one of the 4 speeds available.
CAUTION:
Using the high speed electronic shutter indoors with low lighting, will
give darker pictures. In such a case, add some lights to make sure the
lighting is sufficient. If the lighting is very bright, pay attention to the
light angle in order to avoid or minimize the smear phenomenon
effect.
Table A (sw tch 2 ~ 3)
1 1/50 2 1/120 3 1/1000 4 1/2000
(Unit: sec.)
Aperture
If you would like to emphasize the contours of the
object, set the switch 4 (AP) to the up (SHRP) position.
1
23 23 23 23
4
L5AK4/XE, L5AL4/XE GB 2003, 6, 5
6 English

SETTINGS
Backl ght compensat on sett ng
This camera has two different backlight
compensation functions: Normally backlight
compensation switch 5 (BL-M) and 6 (BL-C)
are set to the down (OFF) position. Change
the backlight compensation switch settings
depending on the conditions.
•BL-M mode:
(Mult -spot)
Use this position when applying backlight
compensation to the whole of the screen.
•BL-C mode:
(Centre-focus)
Use this position when applying backlight
compensation to only the central portion of the
screen.
Note:
•If switches 5 and 6 are set to the up (ON) position at the same
time, the BL-M setting will have priority.
•hen BL-M mode is set, scenes with no backlighting may appear
extremely dark and the object may appear over-exposed. If this
happens, set to BL-C mode.
5 6
(BL-M mode: 64 sect ons)
(BL-C mode)
L5AK4/XE, L5AL4/XE GB 2003, 6, 5
English 7

SETTINGS
Wh te balance adjustment
Normally the switch 7 (WB) is set to the down (ATW: auto white
balance) position and the white balance is adjusted automatically. If a
manual white balance adjustment is necessary, follow the steps below.
Set the switch 7 (WB) to the up (MANU: manual) position, then
adjust the colour.
•Turn R (VR302) to set the red ratio and/or B (VR303) to set the
blue ratio.
Synchron zat on sett ngs
The default setting is internal synchronization (INT). You can change
the power supply synchronization by moving switch 8 to the up (LL)
position. Refer to “L ne phase adjustment” for details.
L ne phase adjustment
hen using a camera switcher to connect 2 cameras or more to one
monitor, there may be a vertical roll of the images when switched. In
such a case, set as described below.
1Set the switch 8 (SYNC) to the up (LL) position.
2Switch the display on the monitor from camera 1 to camera 2.
Adjust the PHASE volume on camera 2 until the vertical roll of the
image stops.
If more than two cameras are used, please repeat this procedure
for all the cameras.
CAUTION:
If the vertical roll cannot be corrected by setting the PHASE volume
on camera 2, try setting the PHASE volume on camera 1. If it still
cannot be corrected, please check that the polarity of the power
cords of all connected devices is correct.
7
VR302VR303
BR
WB
8
VR322
PHASE
L5AK4/XE, L5AL4/XE GB 2003, 6, 5
8 English

SETTINGS
Manual colour/black and wh te sett ng
Connect each cable as indicated below, to set the image to black and
white or colour as desired.
•Colour mage sett ng
Connect the Colour (yellow) and the Wh te (ground) cables.
•Black and wh te sett ng
Connect the B/W (purple) and the Wh te (ground) cables.
Day/n ght cable Image
Colour B/W
OFF OFF Auto
OFF ON Black and wh te
ON OFF colour
ON ON Auto
ON : Close
OFF : Open
Notes:
•The maximum length of cable for CONTROL terminal is 600 m (A G 24).
•During optical filter switching, even if the manual switching operation is
done, you cannot determine if the image is black and white or colour.
Manual switching will have to be done one more time.
•hen using a day/night setting, the accessory ferrite core (two winds) must
be installed to the day/night cable in order to prevent electromagnetic
interference with the other connected devices.
Lens r s adjustment
You will need to set the LEVEL (VR121) volume when shooting in the
conditions described below.
Counterclockw se: To decrease the contrast
Clockw se: To increase the contrast
•If shooting simultaneously in a dark room and through a bright
window.
•If the subject background is extremely bright or dark.
•If the brightness of the picture on the monitor is not correct.
GND
(Wh te)
Colour
(Yellow) B/W
(Purple)
VR121
L5AK4/XE, L5AL4/XE GB 2003, 6, 5
English 9

ADJUSTMENT
Adjust ng the lens Once the camera has been installed, adjust the lens section.
1Tighten the pan adjustment screw.
Model: VDC-D2185VP
Loosen the pan adjustment screw, adjust the panning position of
the lens and then re-tighten the screw.
Model: VDC-D1185VP
Remove the lens unit A from the pan chassis, loosen the pan
adjustment screw B, turn the chassis to adjust the panning
position to a position where one of the three screw holes C is
visible, and then re tighten the screw.
2Loosen the tilt adjustment screw, adjust the tilting position of the
lens and then re-tighten the screw.
3Loosen the zoom lever screw, turn the zoom lever
counterclockwise to determine the zoom position while viewing
the camera images on the monitor, and then re-tighten the screw.
4Loosen the focus lever screw, turn the focus lever
counterclockwise to determine the focus position while viewing
the camera images on the monitor, and then re-tighten the screw.
Note: Be careful not to touch the lens section when changing the
angle of the camera.
3
4
1
1
2
A
B
C
C
C
Model: VDC-D2185VA
Model: VDC-D1185VA
L5AK4/XE, L5AL4/XE GB 2003, 6, 5
10 English

ADJUSTMENT
MONITOR output p n
hen setting up the camera, connect a monitor to this video output
pin and to the GND screw using alligator clip cables, then using the
image displayed on the monitor, set the surveillance angle and range,
the lens focus, etc.
TROUBLESHOOTING
Before taking the camera for repairs, please check below to make
sure that the camera is used correctly. If it still does not perform
correctly, please consult your dealer or a Sanyo Authorized Service
Centre.
No p cture on the mon tor screen
•Is the power turned on to all connected devices? Is the voltage
correct?
•Are all the signal connecting cables correctly connected?
•Is the lighting sufficient?
The p cture s not clear
•Is the monitor correctly adjusted?
•Is the lens focus correctly adjusted?
•Are the lens surfaces clean?
If there is dust or finger prints on the lens, the image quality will
deteriorate. To clean the lens use a soft cloth or a commercially
available lens cleaning set.
SERVICE
This camera is a precision instruments and if treated with care, will
provide years of satisfactory performance. However, in the event of a
problem, the owner is advised not to attempt to make repairs or open
the cabinet. Servicing should always be referred to your dealer or
Sanyo Authorized Service Centre.
L5AK4/XE, L5AL4/XE GB 2003, 6, 5
English 11

SPECIFICATIONS
Scann ng system : PAL standard
(625 TV lines, 25 frames/sec.)
Interlace : PLL 2:1 interlace
Image dev ce : 1/4 inch solid state image device CCD
P cture elements : 795 (H) x 596 (V)
Effect ve p cture elements : 752 (H) x 582 (V)
Synchron z ng system : Internal sync, Line lock
Resolut on : 520 TV lines horizontally, 400 TV lines
vertically
V deo output level : 1.0 Vp-p/75 ohms, composite
V deo S/N rat o : More than 48 dB
M n mum requ red
llum nat on
( ncandescent l ght ng)
:Approx. 0.06 lux with a F 1.4 lens
(B/ mode),
Approx. 1.2 lux with a F 1.4 lens
(colour mode)
Power and Day/n ght
cable :Manual colour/black and white setting
Backl ght compensat on : Manual ON (Multi-spot photometry,
Centre-focus photometry)/OFF
switching
(Active when using an auto-iris lens)
Electron c shutter : 4 speeds, selectable by switches:
(1/50, 1/120, 1/1000, 1/2000 sec.)
Wh te balance : AT /Manual switching
Pan/T lt adjustment : Manual Pan: ±180 degree,
Tilt: 115 degree
Lens : f=2.8 – 5.8 mm, F1.4 – F1.8
Env ronmental cond t ons : Temperature: –10° C ~ +50° C
Humidity: less than 90% (no
condensation)
Power supply : 24 V AC, 50 Hz and 12 – 15 V DC
Power consumpt on : 2.9
We ght : VDC-D1185VP: Approx. 1,350 g
VDC-D2185VP: Approx. 1,015 g
D mens ons (mm)
Features and spec f cat ons are subject to change w thout pr or
not ce or obl gat ons.
100.5
114.8
162.0
162.0
73.0
100.5
29
85.8
114.8
VDC-D1185VP VDC-D2185VP
L5AK4/XE, L5AL4/XE GB 2003, 6, 5
12 English

Printed on recycled paper
Gedruckt auf recyceltem Papier
Imprimé sur du papier recyclé
1AC6P1P2678--
L5AK4/XE, L5AL4/XE (0603KP-CZ)
Sanyo Electric Co, Ltd.
Printed in Japan
L5AK4/XE, L5AL4/XE GB 2003, 6, 6