Sapido RB-6132 User manual

http://www.sapido.com.tw 1 USER MANUALV1.0

http://www.sapido.com.tw 2 USER MANUAL V1.0
FCC Statement
Federal Communication Commission Interference Statement This equipment has
been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
1. The device complies with Part 15 of the FCC rules. Operation is subject to the
following conditions:
2. This device may not cause harmful interference, and this device must accept any
interference received, including interference that may cause undesired
operation.
3. FCC RF Radiation Exposure Statement: The equipment complies with FCC RF
radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body.
4. This Transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
5. Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user authority to operate the
equipment.
IMPORTANT NOTE
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance20cm between the radiator & your body.

http://www.sapido.com.tw 3 USER MANUAL V1.0
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
National Restrictions
Frequency range - 2400.0 - 2483.5 MHz
Country Country Reason/remark
Bulgaria none General authorization required for outdoor use
and public service.
France Outdoor use limited to 10 mW e.i.r.p. within the
band 2454-2483.5 MHz
Military Radiolocation use. Refarming of the 2.4
GHz band has been ongoing in recent years to
allow current relaxed regulation. Full
implementation planned 2012.
Italy none If used outside of own premises, general
authorization is required.
Luxembourg none General authorization required for network and
service supply (not for spectrum).
Norway Implemented This subsection does not apply for the geographical area within a radius of 20 km from
the centre of Ny-Ålesund.
Russian
Federation none Only for indoor applications.
Note: Please don’t use the product outdoors in France
CE Statement of Conformity
Our product has been tested in typical configuration by Ecom Sertech Corp and was found to
comply with the essential requirement of "Council Directive on theApproximation of the Laws
of the Member Sates relating to Electromagnetic Compatibility" (89/336/EEC; 92/31/EEC;
93/68/EEC). The Declaration of Conformity can be found at the Sapido regional website.
www.sapidotech.de
CE Information of Disposal
The electric and electronic equipment or unit which is labeled with crossed-out wheeled bin
may not be disposed of with household waste. This mark is based on European Directive
2002/96/EC (for Waste Electric and Electronic Equipment=WEEE).
Please take it to the designated collection facilities. We will ensure the proper recycling, reuse
and other forms of recovery of WEEE. WEEE has the potential effects on the environment
and human health as a result of the presence of hazardous substances. You can contribute to
eliminate these effects by your cooperation.

http://www.sapido.com.tw 4 USER MANUAL V1.0
Table of Contents
Chapter 1 Introduction.................................................................................................................6
1.1 Overview ......................................................................................................................6
1.2 Features.......................................................................................................................7
1.3 Specifications..............................................................................................................8
1.3.1 Product Appearance ........................................................................................10
1.3.2 LED Indicator Status Description...................................................................10
1.4 System Requirements ..............................................................................................11
1.5 Get Your IP Automatically & Manually ....................................................................11
1.5.1 Network Testing................................................................................................15
1.5.2 Testing with Internet Browser.........................................................................15
1.5.2.1 Testing with DOS (Windows XP Platform).............................................15
Chapter 2 Hardware Installation................................................................................................18
2.1 Diagram of Connecting Hardware to RB-6132 Broadband Router ......................18
2.1.1 Hardware Connection and Application for Router Mode.............................18
Chapter 3 One Button Setup......................................................................................................19
3.1 One Button Setup configuration for Router Mode ................................................19
Chapter 4 Router Setup..............................................................................................................23
4.1 Administrator Setup Instruction..............................................................................23
4.2 IP Configuration........................................................................................................23
4.2.1 WAN ...................................................................................................................24
4.2.2 WAN Interface–3.5G (HSDPA/UMTS)..............................................................24
4.2.3 WAN Interface– Ethernet Port.........................................................................25
4.2.4 WAN Interface– WiMAX....................................................................................26
4.2.5 WAN Interface– Wireless .................................................................................27
4.2.6 WAN Access Type – Static IP ..........................................................................28
4.2.7 WAN Access Type –Dynamic IP......................................................................31
4.2.8 WAN Access Type –PPPoE..............................................................................33
4.2.9 WAN Access Type – PPTP...............................................................................35
4.2.10 LAN Interface Setup.........................................................................................38
4.2.11 Dynamic DNS Setting.......................................................................................40
4.3 Wireless Setup ..........................................................................................................41
4.3.1 Wireless Basic Settings...................................................................................42
4.3.2 Wireless Advanced Settings ...........................................................................47
4.3.3 Wireless Security Setup ..................................................................................48
4.3.4 Wireless Access Control .................................................................................51

http://www.sapido.com.tw 5 USER MANUAL V1.0
4.3.5 WDS Settings....................................................................................................52
4.3.6 WPS ...................................................................................................................57
4.4 NAT.............................................................................................................................62
4.4.1 Visual Server.....................................................................................................62
4.4.2 Visual DMZ........................................................................................................64
4.5 Firewall.......................................................................................................................64
4.5.1 Port Filtering.....................................................................................................65
4.5.2 IP Filtering.........................................................................................................66
4.5.3 MAC Filtering....................................................................................................68
4.5.4 URL Filtering.....................................................................................................69
4.6 System Management ................................................................................................70
4.6.1 Change Password ............................................................................................71
4.6.2 Upgrade Firmware............................................................................................71
4.6.3 Profiles Save.....................................................................................................73
4.6.4 Time Zone Setting ............................................................................................77
4.6.5 UPnP Setting.....................................................................................................79
4.6.6 Language Setting.............................................................................................79
4.7 Log & Status ..............................................................................................................81
4.7.1 Network Config.................................................................................................81
4.7.2 Event Log..........................................................................................................82
4.8 Logout........................................................................................................................84
Chapter 5 AP mode.....................................................................................................................85
Chapter 6 WiFi AP mode ............................................................................................................87
Chapter 7 DDNS Service Application........................................................................................88
Chapter 8 Q & A ..........................................................................................................................95
8.1 Installation .................................................................................................................95
8.2 LED.............................................................................................................................95
8.3 IP Address..................................................................................................................96
8.4 OS Setting..................................................................................................................96
8.5 RB-6132 Broadband Router Setup..........................................................................97
8.6 Wireless LAN.............................................................................................................99
8.7 Support ....................................................................................................................101
8.8 Others.......................................................................................................................102
8.9 USB Device..............................................................................................................102
Chapter 9 Appendices..............................................................................................................103
9.1 Operating Systems .................................................................................................103
9.2 Browsers..................................................................................................................103
9.3 Communications Regulation Information ............................................................103

http://www.sapido.com.tw 6 USER MANUAL V1.0
Chapter 1 Introduction
1.1 Overview
RB-6132 Broadband Router is a convenient wireless solution for delivering 802.11n wireless
connectivity with a maximum wireless signal rate of up to 150Mbps. Use it in home or
company.
Moreover, with connect to a 3.5G (EVDO/HSPA) or WiMAX USB modem, this RB-6132
Broadband Router allows user to share the wireless network outdoor or be an alternative or
backup to fixed broadband.

http://www.sapido.com.tw 7 USER MANUAL V1.0
1.2 Features
Wall mount :This product is recessed wireless router, not only
allow multiple computers or Internet devices connect to the Internet
easily , but can mount into wall.
UPnP Supported : insert your 3.5G or WiMAX modem card and enjoy the Internet
without extra setting
3.5G and Wireless RB-6132 Combo : Ideal for mobility or backup for fixed lined
connection
WPS button provides not only an easy and secured wireless network but also a WDS
repeater in one push
Multiple APs Supported : adds or limits the properties for classed SSID, increasing the
flexibility and efficiency of the network.

http://www.sapido.com.tw 8 USER MANUAL V1.0
1.3 Specifications
Item Specification
Key Components
Main Processor Realtek RTL8196C (400MHz )
Flash 8Mbytes Serial Flash
RAM 32Mbytes SDRAM
Wireless Chip Realtek RTL8188RE-VL (MAC+BB+RF) 1T1R
Communication Interfaces
WAN/LAN Port 1 x 10/100 Mbps RJ45 with auto MDI/MDIX
LAN Port 1 x 10/100 Mbps RJ45 with auto MDI/MDIX
USB Port USB 2.0 host x1 (supports 3.5G or WiMAX USB
dongle)
Wireless IEEE 802.11 b/g/n
Others
Wireless Antenna External 3dBi x1
Transmission Power TBD
Receive Sensitivity
11Mbps : TYP. -83dBm @ 8% PER
54Mbps: TYP. -70dBm @ 10% PER
11n (20MHz): TYP. -64dBm @ 10% PER
11n (40MHz): TYP. -61dBm @ 10% PER
Slide Switch Router / AP / WiFi AP Mode switch
Button
Power on/off button。
Reboot button / Reset button –1second for reboot；
10seconds for reset
WPS button。
Operation Requirement
Operating Temp. 0 to 40℃
Storage Temp. -20 to 70℃
Operating Humidity 10% to 85% Non-Condensing
Storage Humidity 5% to 90% Non-Condensing
Power Supply AC100~240V / 50~60Hz universal input
Dimensions 72.6(L) x 48.1(W) x 49(D) mm (main body only)
Device Weight TBD

http://www.sapido.com.tw 9 USER MANUAL V1.0
Notice:
1. USB device with power more than 500mA is not supported

http://www.sapido.com.tw 10 USERMANUAL V1.0
1.3.1 Product Appearance
Power Receptor AC100~240V / 50~60Hz universal input
WPS Push “WPS” button to looking for other WPS devices. The security will be
set up between these 2 Wi-Fi devices after pairing.
Reset Button Press “Reset” button over 10 seconds. When status indicator turns from
flashing to solid, the process is completed.All settings are back to default.
Ethernet Port 1x WAN port（back）, 1x WAN/LAN ports
USB2.0 Ports 1 USB Port
Mode switch Router/AP/WiFi AP mode
WAN
1.3.2 LED Indicator Status Description
LED Function Color Status Description
On System is ready to work
Status x 1 System status Green Blinking
120ms Rest to default in progress
On Wireless is active
Wireless / WPS
x 1
Wireless activity
& Green
Blinking Wireless Tx/Rx activity

http://www.sapido.com.tw 11 USERMANUAL V1.0
30msWPS status
Reddish
Orange
Blinking
120ms WPS function in progress
On 100Mbps Ethernet is connected
Green Blinking
30ms 100Mbps Ethernet Tx/Rx activity
On 10Mbps Ethernet is connected
WAN/LAN x 1 WAN/LAN port
activity
Green Blinking
120ms 10Mbps Ethernet Tx/Rx activity
On 100Mbps Ethernet is connected
Green Blinking
30ms 100Mbps Ethernet Tx/Rx activity
On 10Mbps Ethernet is connected
LAN x 1 LAN port activity
Green Blinking
120ms 10Mbps Ethernet Tx/Rx activity
1.4 System Requirements
To begin with RB-6132 Broadband Router, you must have the following minimum system
requirements. If your system can’t correspond to the following requirements, you might get
some unknown troubles on your system.
XDSL/Cable Modem and broadband Internet Account.
One Ethernet (10 BASE-T or 10/100 BASE-TX) network interface card.
One PC or Notebook with web browser software installed (E.g.: Internet Explorer 5.0,
Netscape Navigator 7.x, Apple Safari 2.03 or higher version).
At lease one 802.11b/g/n wireless adapter for wireless mobile clients.
Recommended OS: Win2000 or WinXP / Linux.
1.5 Get Your IP Automatically & Manually

http://www.sapido.com.tw 12 USERMANUAL V1.0
After RB-6132 Broadband Router connected with your computer, please make sure your IP is
in the automatic IP position or you adjust it manually in order to activate the Internet network
from home to Internet. If you don’t know how to enter the settings, please follow the steps as
below.
Step 1. Go to Start>Settings>Network Connections and then select Local Area
Connection.
Step 2. Click on Properties

http://www.sapido.com.tw 13 USERMANUAL V1.0
Step 3. Double click on Internet Protocol (TCP/IP).
Step 4-1. For getting IP automatically if you are one of the users under RB-6132 Broadband
Router, please skip Use the following IP address and then select Obtain an IP address
automatically and Obtain DNS server address automatically and then click on OK button.

http://www.sapido.com.tw 14 USERMANUAL V1.0
Step 4-2. For getting IP manually in order to specify a Virtual Server, such as Print Server,
FTP Server and so on, please skip Obtain an IP address automatically and then select Use
the following IP address. And the following default setting of RB-6132 Broadband Router
should be noted:
IPAddress: 192.168.1.10 (as your Print Server for example)
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.1
Note:If you configure your computer’s IP Address manually, it needs to be on the same
network segment.
For example:
IPAddress: 192.168.1.xxx (xxx can be any number between 2 and 253, but it can’t be
repeated, we use 100 to be the example.)
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.1 (this is the IP address of RB-6132 Broadband Router in Router
Mode)
DNS: 192.168.1.1 (use RB-6132 Broadband Router’s IP address or on your own choice)
Note:IP address and Default gateway cannot be the same.

http://www.sapido.com.tw 15 USERMANUAL V1.0
1.5.1 Network Testing
There are two ways to test your Network whether it can work on Internet or not. They are
“Testing with Internet Browser” and “Testing with Dos”.
1.5.2 Testing with Internet Browser
Open an Internet Browser, such as Internet Explore or Netscape. Input a valid web address
you like, for example, http://www.yahoo.com in the web address blank and then press
enter. If the website appears, that means your Internet is working under normal situation.
1.5.2.1 Testing with DOS (Windows XP Platform)
Step 1. Go to start > Run.

http://www.sapido.com.tw 16 USERMANUAL V1.0
Step 2. Input cmd in the blank, and then click OK button. The Command Prompt window
appears.
Step 3. Input ipconfig in the flashing area then press enter. You will get an IP Address
192.168.1.100, for example, and Default Gateway as 192.168.1.1.
Step 4. Ping a legal WAN Address such as 192.168.1.1. If Internet works, it will show Reply
from 192.168.1.1: bytes = 32 time = 3ms TTL =64, for example.

http://www.sapido.com.tw 17 USERMANUAL V1.0
If it can’t work, it will show Request timed out.

http://www.sapido.com.tw 18 USERMANUAL V1.0
Chapter 2 Hardware Installation
2.1 Diagram of Connecting Hardware to RB-6132 Broadband Router
RB-6132 Broadband Router is a portable and convenient wireless solution for delivering
802.11n wireless connectivity with a maximum wireless signal rate of up to 150Mbps. Use it in
conference rooms, hotel rooms, or even at hotspots.
2.1.1 Hardware Connection and Application for Router Mode
When RB-6132 Broadband Router switches to Router Mode, there will be each WAN and
LAN port existing, the administrator can do the Quick Setup including WAN Setup, LAN Setup,
Wireless Setup, Time Server Setup, Password Setup, Firewall Setup.

http://www.sapido.com.tw 19 USERMANUAL V1.0
Chapter 3 One Button Setup
The advanced One Button Setup provides users a simple way to set up the complicated
network. Instead of numbers of IPs to be memorized, you just need to fill in some necessary
information and then enjoy the secured internet by clicking the “Finished” button.
3.1 One Button Setup configuration for Router Mode
The default UPnP of RB-6132 Broadband Router is ON. When users connect RB-6132
Broadband Router to their PC, and icon will show up in the right-down corner.
Step 1. Click the Internet Gateway Device to open the login page.

http://www.sapido.com.tw 20 USERMANUAL V1.0
Step 2. Click One Button Setup on the left of the main menu under router mode.