Sapido BR476n User manual

FCC Caution
FCC Part 15.19 Caution:
•This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions
◦this device may not cause harmful interference and
◦this device must accept any interference received, including interference that
may cause undesired operation
•This device and its antenna(s) must not be co-located or operating in conjunction
with any other antenna or transmitter.
•Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user authority to operate the equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
The antennas used for this transmitter must be installed to provide a separation distance
of at least 20 cm from all persons and must not be co-located or operating in conjunction
with any other antenna or transmitter.
FCC Statement in ser’s Manual (for calss B)
FCC Section 15.105
“Federal Communications Commission (FCC) Statement”
This equipment has been tested and found to comply with the limits for a lass B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
CE Statement of Conformity
Our product has been tested in typical configuration by Ecom Sertech Corp and was found
to comply with the essential requirement of “Council Directive on the Approximation of the
Laws of the Member States relating to Electromagnetic Compatibility” (89/336/EEC;
92/31/EEC; 93/68/EEC)

1 Introduction Product Appearance
1.1 LED Indicator Status Description：
LED Function Color Status Description
Power indicator Green On Power is being applied to this
product
WAN port activity Green On 10/100Mbps Ethemet is connected
Blinking
30ms
100Mbps Ethemet Tx/Rx activity
Blinking
120ms
10Mbps Ethemet Tx/Rx activity
WAN port activity Green On 10/100Mbps Ethemet is connected
Blinking
30ms
100Mbps Ethemet Tx/Rx activity
Blinking
120ms
10Mbps Ethemet Tx/Rx activity
Wireless activity
&WPS status
Green On Wireless is connected
Green Blinking
30ms
Wireless Tx/Rx activity
Reddish Blinking
120ms
WPS function in progress
2 System overview and Network Setup
2.1 System overview
•Many connecting way
BR476n provides many Internet connecting way. It provides not only Ethernet
(wired), but also 802.11n Wi-Fi、3.5G、Smartphone、LTE for user to choose.
•Rigorous Security mechanism
BR476n provides Wireless Security, Firewall to make sure that the data of user in
network are protected securely.
•Easy to configure and manage
With convenient Web-based UI, user can configure easily and browse system
information and status. BR476n can detect 3.5G system and connect to Internet
automatically. If user changes Internet-connecting way to Ethernet, BR476n will
detect it and connect Internet automatically.
•One Touch Encrypted Wireless connection
BR476n has entity WPS button to make wireless connecting more easy. All user
should do is just One Touch.
•SB File Sharing
BR476n has USB 2.0 port.to connecte external hard disk or flash driver. User can
easily share files through the built-in Samba Server functionality.
•Green AP Power-saving function
When Wireless and CPU are full loading, the output power of wireless and CPU will
reach maximum. When Wireless and CPU are standby, system will decrease the

output power of wireless and CPU. System will enable this function automatically
without any setup by user. This function will decrease the temperature and enlarge
the battery life.
•IEEE 802.3az supported
First, it detects link status, allowing each port on the switch to power down into a
standby or ‘sleep’ mode when a connected device, such as a computer, is not
active. Second, it detects cable length and adjusts the power accordingly.
2.2 Hardware Main Features
•USB2.0 Host
◦Support 3.5G/4G USB dongle
◦Support Smart Phone
◦Support USB Storage、USB HDD
◦Support USB Webcam
•Dock
◦Support iPhone charging
◦Support iPhone hotspot
◦Support iPhone audio to AUX out
◦Support H C mobile phone charging
◦Support Samsung mobile phone charging
◦When mobile phone on dock，BR476n can be a hotspot
•3.5mm AUX out for audio airplay
2.3 Connecting BR476n
Administrator can manage the settings for WAN, LAN, Wireless Network, NTP, password,
VPN, Firewall, etc.
Please confirm the network environment or the purpose before setting this product.
•Prepare the followings before the connection
•PC or Notebook for setup
•Wireless connection （Ethernet port default is for internet）
•Make sure you are under “Router Mode”.
•Turn on your Computer.
•Connect BR476n ethernet port to xDSL/ Cable modem with the Ethernet cable /
3.5G dongle / LTE dongle / smartphone.
•Connect PC/NB to BR476n by wireless.
•After your computer obtained an IP address from wireless router, please start your
web browser, and input the IP address of the wireless router（192.168.1.1）in
address bar, and the following message should be shown. Default account and
password are “admin”

•Users can set or change user name and password used for accessing the web
management interface in this section.
•Input User Name and New Password, then input confirm password again.

3 Function introduction
Open a Web browser, and enter http //192.168.1.1 (Default Gateway)
3.1 Home menu
Click Home button icon to enter MENU as below.
Download
pdapp
Status page Logout

Item Description
Internet Setup There are several different method to access
Internet，PPPoE、DHCP、Static
IP、PPTP、L2TP、WiFi ISP
AP If a router is already set at the house, and you want to
make the wireless LAN communication
WiFi AP When you connect to the internet wirelessly through
PC and wireless device without wireless LAN function
equipped.
Firmware Upgrade This function allows you upgrade the BRB72N firmware
to new version. Please note do not power off the device
during the upload because it may crash the system.
Parental control You can use URL filter 、MAC Filter Schedule and
Wireless Schedule to limit access Internet.
Office Control For office environment，there are Multiple
AP、Wireless Access Control、IP Filtering、IP Binding
and QoS
File Menu There are Samba Storage and FTP server features
Webcam server For image record
VPN Server PPTP/L2TP general setup introduction.
DoS Denial of Service
Remote management This page allow you to access the GUI on WAN.
Advance Setup Advance setting menu
Status You could check WAN, LAN, Client network in status.
Factory Default You could reset the current configuration to factory
default.
Reboot This function is used to reboot
Logout This page is used to logout.

3.2 Internet Setup
Click Internet Setup icon to enter WAN setup as below. The Internet Setup is depended on
the service that you contract with the provider. The BRB72N provides five selections for
the Internet Mode type, PPPoE, DHCP, Static IP , PPTP and L2TP 、WiFi
ISP、3.5G、Smart Phone、LTE. Check with your ISP if you don’t know the WAN type

3.2.1 PPPoE
Item Description
User Name Input your user name provided by your ISP. If you don’t
know, please check with your ISP.
Password Input the password provided by your ISP.
Wireless AP Turn on/off wireless
SSID Service Set identifier, users can define to any or keep
as default.
Encryption Select wireless encryption type form the drop-down list.

3.2.2 DHCP
Item Description
MAC type Select "Universal” or “Specific"
Universal：clone controller PC mac address as
BR476n WAN mac address
Specific：use BR476n itself mac address
Wireless AP Turn on/off wireless
SSID Service Set identifier, users can define to any or keep
as default.
Encryption Select wireless encryption type form the drop-down list.

3.2.3 Static IP
Item Description
IP Address Enter the IP address which is provided by your ISP.
Subnet Mask Please enter the Subnet Mask address
Gateway Input ISP Default Gateway Address.
DNS Input DNS information which is provided by your ISP
Wireless AP Turn on/off wireless
SSID Service Set identifier, users can define to any or keep
as default.
Encryption Select wireless encryption type form the drop-down list.

3.2.4 PPTP
Item Description
Address Mode Select "Dynamic" or "Static"
Server IP Address Input your server IP address provided by your ISP. If
you don’t know, please check with your ISP.
User Name Input PPTP account provided by your ISP.
Password Input the password provided by your ISP.
MTU Size Maximum Transmission Unit. Usually provide by
computer operation systems (OS). Advanced users can
set it manually.
Enable MPPE
Encryption
Microsoft Point-to-Point Encryption (MPPE) provides
data security for the PPTP connection that is between
the VPN client and VPN server.
Enable MPPC
Compression
Microsoft Point-to-Point Compression (MPPC) is a
scheme used to compress Point-to-Point Protocol
(PPP) packets between Cisco and Microsoft client
devices. The MPPC algorithm is designed to optimize
bandwidth utilization in order to support multiple
simultaneous connections. The MPPC algorithm uses a
Lempel-Ziv (LZ) based algorithm with a continuous
history buffer, called a dictionar
Wireless AP Turn on/off wireless
SSID Service Set identifier, users can define to any or keep
as default.
Encryption Select wireless encryption type form the drop-down list.

3.2.5 L2TP
Item Description
Address Mode Select "Dynamic" or "Static"
Server IP Address Input your server IP address provided by your ISP. If
you don’t know, please check with your ISP.
User Name Input L2TP account provided by your ISP.
Password Input the password provided by your ISP.
MTU Size Maximum Transmission Unit. Usually provide by
computer operation systems (OS). Advanced users can
set it manually.
Wireless AP Turn on/off wireless
SSID Service Set identifier, users can define to any or keep
as default.
Encryption Select wireless encryption type form the drop-down list.

3.2.6 WiFi ISP
BR476n WAN get IP address from other wireless AP and LAN/Wireless LAN client get IP
from BR476n
Item Description
Survey List all available wireless AP
Pre-Shared Key Input the wireless AP key which you want to connect
Extend SSID Provide SSID for wireless client which want to connect
to BR476n
Encryption Select wireless encryption type form the drop-down list.

3.2.7 3.5G
Item Description
Mode Input your user name provided by your ISP. If you don’t
know, please check with your ISP.
Network Traffic Monitor BR476n will record 3.5G traffic usage volume
Limit Internet Traffic User can limit 3.5G traffic usage volume to prevent
over budget
Connection Speed Provide 3 kinds of speed，auto is recommended
SIM PIN SIM card PIN number
Authentication Provide 3 kinds of authentication methods，auto is
recommended
Wireless AP Turn on/ off wireless function
SSID Service Set identifier, users can define to any or keep
as default.
Encryption Select wireless encryption type form the drop-down list.

3.2.8 Smartphone
Item Description
Service BR476n support 4 kinds of smart phone、Nokia、Black
Berry、Sansung、iPhone and Andriod phone
iPhone and Andriod phone do not need to do any
setting，all you need is to turn on hotspot function
and connect it to SB port
Region Select correct phone service region
ISP Select correct phone service ISP
APN Please check 3.5G ISP to get APN data
User Name Please check 3.5G ISP to get user name
Password Please check 3.5G ISP to get password
Phone number Please check 3.5G ISP to number data
Authentication Provide 3 kinds of authentication methods，auto is
recommended
Wireless AP Turn on/ off wireless function
SSID Service Set identifier, users can define to any or keep
as default.
Encryption Select wireless encryption type form the drop-down list.

3.2.9 LTE
Item Description
Mode Input your user name provided by your ISP. If you don’t
know, please check with your ISP.
Network Traffic Monitor BR476n will record 3.5G traffic usage volume
Limit Internet Traffic User can limit 3.5G traffic usage volume to prevent
over budget
Connection Speed Provide 3 kinds of speed，auto is recommended
SIM PIN SIM card PIN number
Authentication Provide 3 kinds of authentication methods，auto is
recommended
Wireless AP Turn on/ off wireless function
SSID Service Set identifier, users can define to any or keep
as default.
Encryption Select wireless encryption type form the drop-down list.

3.3 AP
If a router is already set at the house, and you want to make the wireless LAN
communication. This mode does not support
WAN、DHCP、NAT、DDNS、QoS、Firewall、Static/Dynamic route、VPN Server features
Item Description
Wireless AP Turn on/off wireless
SSID Service Set identifier, users can define to any or keep
as default.
Encryption Select wireless encryption type form the drop-down list.
Wireless AP Turn on/off wireless

3.4 WiFi AP
When you connect to the internet wirelessly through PC and wireless device without
wireless LAN function equipped. This mode does not support
WAN、DHCP、NAT、DDNS、QoS、Firewall、Static/Dynamic route、VPN Server features
.
Item Description
Survey List all available wireless AP
Pre-Shared Key Input the wireless AP key which you want to connect
Extend SSID Provide SSID for wireless client which want to connect
to BR476n
Encryption Select wireless encryption type form the drop-down list.

3.5 Firmware pgrade
This function can upgrade the firmware of the router. There are two methods for user
upgrade firmware Auto upgrade and Manual upgrade.
Caution: To prevent that firmware upgrading is interrupted by other wireless
signals and causes failure. We recommend users to use wired connection during
upgrading.
Note: The firmware upgrade will not remove your previous settings.
3.5.1 Auto upgrade
It provide auto detect new firmware from Internet, and user can select to upgrade new
version or not.
3.5.2 Manual upgrade
If you download firmware from website, you can upgrade firmware manual as below.