Sartorius PMA.World User manual

98648-015-22
Installation Instructions
Sartorius PMA.World | PMA.Net
Model PMA 7501-X00G | PMA 7501-X00GL
Electronic Paint-mixing Scales for Use in Zone 1 Hazardous Areas
98648-015-22

2
General View of the Equipment
PMA7501-X00G | PMA7501-X00GL
(PMA.World | PMA.Net)
Electronic Paint-mixing Scales for Use in Zone 1 Hazardous Areas
1 Display and control unit
2 Qkey (On/Standby)
3 Rkey: Upwards
4 Skey: Downwards
5 Ukey: Zero/Tare
6 Ikey (TOGGLE)
You can toggle to two decimal places
– from 0.05 g to 999.95 g – or tog-
gle between – “g” and “p” – parts per
pound, depending on the menu settings
7 Kfactor key (FORMULATION) for
paint-mixing applications
8 ckey (Clear) and [REC] key for
paint-mixing applications
9 Lkey [ENTER] and [MEM] key for
paint-mixing applications
10 Graphic display
11 Weighing pan
12 Interfaces (D-Sub connector, 9-contact)
13 DC jack for connection to AC power
14 Grounding terminal
15 Column
16 Joint
1
2
3
4
5
6
7
8
9
11
15
10
12
13
14
16

3
Contents
General View of the Equipment
PMA7501-X00G | -X00GL. . . . . . . . . . 2
Intended Use ................... 3
Warnings and Safety Precautions .... 4
Getting Started.................. 6
Operation......................10
Applications ....................12
Calibration/Adjustment............15
Menu Settings ..................16
Troubleshooting.................21
Care and Maintenance ............22
Recycling ......................23
Interface Description..............24
Specifications ...................25
Accessories .....................26
Documents.....................27
The following symbols are used in these
instructions:
§Indicates required steps
$Indicates steps required only under
certain conditions
> Describes what happens after you have
performed a particular step
– Indicates an item in a list
!Indicates a hazard
The PMA7501-X00G | -X00GL (Series:
PMA.World | PMA.Net) scales feature
a graphic display, and have been specially
designed for use in the paint-mixing
sector.
The PMA.Net is equipped with an Ethernet
interface and can either be directly
connected to the network interface of
a PC, or via a 10BaseT/100BaseTX LAN.
This scale can be operated either using
the keypad on the display and control
unit (in “stand alone” mode) or using
the application software (e.g., paint man-
ufacturers’ paint-mixing applications)
installed on your PC. Communication is
carried out via the data interface.
If required, Sartorius can supply you with
DOS- or WINDOWS®-based device drivers
to generate application programs.
Note:
Read the PMA7501-X.... (Series: PMA.
World | PMA.Net) installation and operat-
ing instructions carefully before connect-
ing the weighing platform and putting it
into operation.
Intended Use

4
Warnings and Safety Precautions
Note:
Improper use or handling can result in
property damage and/or personal injury.
Only qualified personnel may install and
operate the equipment. Make sure you
observe the warnings and safety informa-
tion in their entirety during installation
and operation, as well as while perform-
ing maintenance and repair work on the
equipment. The standards, regulations,
occupational safety requirements and
environmental protection laws valid in
your country must be observed. It is
important that all personnel using the
equipment understand this warning
and safety information, and have access
to the relevant documents at all times.
Furthermore, the warning and safety
information supplied with any electrical
equipment connected, such as peripheral
devices, must be observed as well. The
warnings and safety precautions may
have to be supplemented by the equip-
ment operator. All operating personnel
must be informed of any additions to
these instructions. Make sure the equip-
ment is accessible at all times.
General Provisions for Installing
the PMA7501-X…
PMA7501-X00G | -X00GL (PMA.World
| PMA.Net) models meet the require-
ments defined in EC Directive 94/9/EC for
equipment group II, category 2G and are
marked in accordance with the KEMA05
ATEX1247 X EC type-examination certifi-
cate (refer to the chapter on Documents).
Furthermore, PMA7501-X… models meet
the EC Directives for electromagnetic
compatibility and electrical safety (please
see the chapter on CE Marking).
– The area of use for the PMA7501-X…
models is defined in the type-examina-
tion certificate. All restrictions listed in
the type-examination certificate must
be strictly observed. Operating the
PMA7501-X… models beyond the restric-
tions indicated is not permitted, and
is considered use of the equipment for
other than its intended purpose.
– Any installation work that does not con-
form to the instructions in this manual
will result in forfeiture of all claims under
the manufacturer’s warranty. If you use
the equipment in a hazardous area out-
side Germany, you must comply with
the national electrical code and safety
regulations applicable in your country
(e.g.: EN60079-14). Ask your supplier
for information on the legal regulations
applicable in your country.
– If the equipment housing is opened by
anyone other than persons authorized by
Sartorius, this will negate its conformity
with regulations governing its use and
result in forfeiture of all claims under the
manufacturer’s warranty.
– Installation of the PMA7501-X… in a
potentially explosive atmosphere must be
performed by a certified electrician who is
familiar with the assembly, start-up and
operation of both the system and the rel-
evant guidelines and regulations, and has
the required qualifications for performing
the installation. If you need assistance,
contact your Sartorius dealer or the Sar-
torius Service Center.
– Avoid static electricity. Connect an equi-
potential bonding conductor.
Disconnecting equipotential bonding
conductors is not permitted. The bore
hole is marked by a “ground” symbol.
The wire used for the grounding conduc-
tor should have a cross-sectional diam-
eter of at least 4 mm2. Connect all equip-
ment, including peripheral devices, to the
equipotential bonding conductor.
– Do not expose the scale to extreme
temperatures, aggressive chemical vapors,
moisture, shocks and vibrations.

5
– The displayed values can be affected
when subjected to extreme electromag-
netic influence. When the negative influ-
ence has subsided, the scale will again be
fully operational.
– The equipment must be used indoors
only.
– To ensure safety, disconnect the equip-
ment from power before connecting or
disconnecting the cables or electronic
peripheral devices.
– If you use cables purchased from another
manufacturer, check the pin assignments
in the cable against those specified by
Sartorius before connecting the cable to
Sartorius equipment, and disconnect any
wires that are assigned differently. The
operator shall be solely responsible for
any damage or injuries that occur when
using cables not supplied by Sartorius.
– When connecting the scale to the power
supply, the laws valid in your country
must be observed. If you should have any
questions, please contact your supplier
or Sartorius Customer Service for infor-
mation on the legal regulations applica-
ble in your country. The scale must be
installed by a certified technician to avoid
forfeiture of all claims under the manu-
facturer’s warranty.
– Avoid generating static electricity when
using the in-use dust cover, connect the
equipotential bonding conductor.
– Use only a moistened cloth to clean
the dust cover.
For the User
– Always make sure the equipment is
disconnected from AC power before
performing any installation, cleaning,
maintenance or repair work on the scale.
– If you see any indication that the scale
cannot be operated safely (for example,
due to damage), turn it off and lock it in
a secure place or otherwise prevent use of
the equipment for the time being.
– Chemicals (e.g., gases or liquids) that can
corrode and damage the inside or outside
of the device must be kept away from the
equipment. Handle the equipment and
any accessories in accordance with the IP
rating (EN 60529).
– The casing on all connecting cables,
as well as the casing on wires inside the
equipment housing, is made of PVC.
The casing of the power cable is made
of rubber.
– The allowable operating temperature
range during operation is 0°C to +40°C
+(32°F to +104F). Make sure the place
of installation is adequately ventilated to
prevent build-up of excessive heat.
– Use original Sartorius spare parts, only!
– Never use a hammer to close the lid of a
paint can while it is still on the weigh-
ing pan. Otherwise, you will damage the
weighing system!
– According to Certificate
No. 4420306 553419 issued by TÜV
NORD CERT GmbH (German Inspection
and Safety Authorities), PMA7501-X...
electronic scales may be used in areas
exposed to the risk of fire, provided that
the room is not exposed to relatively large
amounts of accumulated dust and fibers,
and thus a fire risk. Paint-mixing rooms
are free of such accumulated dust and
fibers, and the equipment may be oper-
ated there. Their respective Zone 1 power
supplies, models YPS05-Z.P, YCO11Z
must be installed outside the potentially
explosive atmospheres and thus also
beyond fire-risk areas.

6
Getting Started
§Remove the scale from its packaging.
§After unpacking the scale, check it immediately
for any visible damage as a result of rough handling
during shipment.
Equipment Supplied for Model PMA7501-X00G
– Scale
– Weighing pan
– Power supply
– Cable
– 2+protective plugs (in the column)
PMA7501-X00GL
– Scale
– Weighing pan
– EX-link converter YCO11-Z
– Data cable
– 2+protective plugs (in the column)
Setting Up the Scale
Choose a suitable place to set up the scale.
Avoid exposure to drafts, heat, moisture and vibra-
tion. Make sure to read the instructions carefully
before connecting the scale to AC power.
!Observe the safety precautions and warnings in this
manual.
§Place the weighing pan on the scale.
°C

§Ground the scale. Connect the cable to the ground-
ing terminal (14).
Connecting the PMA7501-X00G | PMA7501-
X00GL to AC Power
The equipment is energized by the power supply
provided. Make sure that the voltage rating printed
on the power supply is identical to your local AC
power rating. When connecting the scale to the
power supply, the laws valid in your country must be
observed. If you should have any questions, please
contact your supplier or Sartorius Customer Service
for information on the legal regulations applicable
in your country. Use only original Sartorius power
supplies. The use of power supplies from other
manufacturers, even if these units have a registered
approval rating from a national testing laboratory,
requires the approval of a certified technician.
!Observe the safety instructions and warnings in this
manual
§Insert the plug into the DC jack (13) on the scale
§Tighten the screws (see arrow)
§Connect the data cable to the power supply.
§Plug the power supply into an electrical AC power
outlet. Ensure that the power supply is installed
outside the potentially explosive atmosphere.
7

> If the YC011-Z EX-link converter is connected, LED
on the converter lights up to indicate that it is
powered.
Connecting Data Cables
Important Note:
!Connect/disconnect data cables to or from equip-
ment used in the potentially explosive area Zone 1
only after the power supply has been disconnected.
§Disconnect the power cord from the wall outlet
(mains).
Connect the data cable to the scale
PMA7501-X00G | -X00GL
(internal RS-232 interface; D-Sub female
connector, 9-contact)
!Only connect the data output port (D-Sub connec-
tor, 9-contact) to certified intrinsically safe circuits.
Observe the parameters stipulated in the EU type-
examination certificate.
§Remove and retain the safety cover with the safety
warning.
§Plug the data cable into the interface port (D-Sub
connector, 9-contact). Securely tighten the data
cable.
Important Note:
– When the data output port is not in use, refasten
the safety cover and safety warning.
– If the internal RS-232 interface of the PMA7501-
X00GL is to be used, an additional menu item must
be configured in Setup (refer to the chapter “Menu
Settings”).
8

Data cable connection only for PMA7501-X00GL
(Ethernet interface RJ45)
§Plug the data cable of the EX link converter YCO11-Z
into the Ethernet interface port RJ45.
§Check the switch position (16).
The switch must be set to the left position
(Ethernet interface).
Note:
The Ethernet interface has already been defined in
Setup, prior to delivery.
Data cable connection only for PMA7501-X00GL
(External RS-232 interface, D-Sub connector,
9-contact to YC011-Z)
If a data cable (D-Sub connector, 9-contact) is to
be connected to the EX link converter YCO11-Z,
the following measures are necessary:
§Remove the protective cap and put it in a safe place.
§Plug in the data cable and securely tighten the
screws.
§The switch must be set to the right-hand position.
Important Note:
– An additional menu item must be configured in
Setup (refer to the chapter “Menu Settings”).
– If the data output port is not in use, please replace
the protective cap.
§After connecting the data cable, plug it into the
socket.
Note:
!You may only activate one data interface at a time.
9

Weighing with One Decimal Place
Place an empty paint can on the weighing pan.
Press the Ukey (5). The display shows “0.0 g.”
Pour in the first component, and read off the weight as
soon as the stability symbol appears; in this case, “g.”
Pour in additional components until the desired weight
of your formula is reached.
Remove the filled paint can from the weighing pan.
Never use a hammer to close the lid of a paint can
while it is still on the weighing pan.
Otherwise, you will damage the weighing system.
10
Turn on the scale using the
Qkey (2). After the scale has been turned on, it will automati-
cally run a self-test.
At the end of this test, 0.0 g
is displayed.
If a different readout is
displayed, zero or tare the
scale using the Ukey (5).
Operation

11
Weighing with Two Decimal Places
Note:
To weigh using two decimal places, you must first
adapt the settings (refer to the chapter entitled “Menu
Settings”)
Press the Ikey (6). The display shows “0.00 g.”
Place an empty paint can on the weighing pan (11).
Press the Ukey (5). The display shows “0.00 g.”
Pour in the first component: 205.50 g.
Read off the weight as soon as the stability symbol
appears; in this case, “g.”
Pour in additional components until the desired weight
of your formula is reached.
Remove the filled paint can from the weighing pan.
Important Note:
If you tare the scale, and then press the Ikey (6) to
toggle to the second decimal place with a resolution of
0.05 g, you can continue weighing with two decimal
places up to 999.95 g.
For weights exceeding 999.95 g, only one decimal place
will be displayed.
Never use a hammer to close the lid of a paint can
while it is still on the weighing pan.
Otherwise, you will damage the weighing system

Applications
Formulation Mode (Calculation by a Factor)
This mode enables you to weigh in amounts that are smaller or larger than that of your basic
formula for a specific paint color (e.g., 250 ml of a 1-l formula).
You can select various factors (amounts) by pressing the Kformulation key (7):
0.25 0.5 0.75 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0.
By pressing the Rkey (3): upwards
or Skey (4): downwards,
you can alter the value – in 0.1 increments, as of factor 1.0
or – 0.01 increments, from factor 0.25 to 1.0.
Important Note:
The flashing arrow non the display means that the weight value shown is not verified
for use in legal metrology (not legal for trade).
Example:
As you pour in the components of your formula, the weight is displayed in “g.”
Let’s suppose you want to weigh only 250 ml of a basic formula that is for a total amount
of 1 l. With the recalculation mode, you do not need to manually recalculate the individual
components.
The basic formula for 1 liter is:
250 g 1st component
+ 250 g 2nd component
+ 500 g 3rd component
Total: 1000 g
12
1. Place the empty paint can on the
weighing pan and tare (zero the display). 2. Press the Kformulation key (7) several
times to select the conversion factor “.25”
used in this example.

13
We have come to the end of our example. According to the display, exactly 1,000 g was
poured in, but the paint can actually contains only 250 g by weight according to the factor
you selected, .25. Follow the same procedure for any other conversion factor or to convert
a 1-gallon formula into quarts.
Weighing Using the Recalculation Mode
Let’s suppose that you poured in too much of one color component for a given formula
(e.g., one consisting of 4 components).
In addition, let’s assume that you previously poured in all of the other amounts exactly
according to each of the values you entered and stored by pressing the Lkey [MEM] (9).
Press the Skey (4) to start the recalculation program. “C” will begin flashing on the display.
To correct the weight displayed to the same value you entered for the given formula, either
scroll upwards using the Rkey (3), or downwards using the Skey (4). When you then press
the Lkey [MEM] (9), the scale will automatically calculate and display the amounts of paint
in “g” to add for each of the other components that you already poured in. This mode thus
ensures that the total result of your formula for these components will be correct.
After pouring in these amounts, you can continue to add the remaining components of your
formula.
Important Note:
You can correct an incorrect amount any number of times. However, the total (liter) quantity
in the paint can will increase each time you correct a component. Therefore, press the ckey
(8) to check how much the total quantity (in liters) will be. (“C” = correction factor)
The arrow nin the display means that the weight shown is not verified for use in legal
metrology (not legal for trade).
3. “.25” is displayed next to the weight
4. Slowly pour in the first component, “250 g”,
until the display shows “250 g.”
5. Pour in the second component, “250 g”,
until the display shows “500 g.”
6. Pour in the last component, “500 g”,
until “1000 g” is displayed.

3. Pour in the first component.
+ 50.0 g
2. Press the Ukey (5)
0.0 g
14
Example (cumulative):
1. Place an empty paint can on
the weighing pan (11).
+ 118.0 g
4. Press the Lkey [MEM] (9).
STO 01 5. Pour in the 2nd component.
+ 110.0 g 6. Press the Lkey [MEM] (9).
STO 02
7. Pour in the 3rd component.
+ 203.0 g
Oops!
You poured in too much!
The correct weight for the
formula is 200.0 g.
8. Press the ykey (4) to start
the recalculation mode.
A “C”= correct flashes on
the display = Correct will
flash on the display.
9. Press the ykey (4) several
times to correct the value to:
+ 200.0 g
10. Press the Lkey [MEM] (9).
COR 01 11. 1. Add the first component.
“C1” is displayed. –1.7 g 12. Pour in paint until 0.0 g is displayed.
0.0 g
13. Press the Lkey [MEM] (9)
COR 02 14. Add the second compo-
nent. “C2” is displayed.
–2.0 g
15. Pour in paint until the
value 0.0 g is obtained.
0.0 g
16. Press the Lkey [MEM].
The scale will automatically
return to the formulation
program. “C” disappears.
+ 200.0 g.
17. To check the total weight,
press the ckey (8) [REC].
“C" = Correction factor,
in this example 1.03.
(Total formulation
weight +correction factor)
18. Add the fourth component
+1000.0 g
We have come to the end
of our example.

15
Calibration/Adjustment
You can calibrate/adjust the scale by pressing the
Ukey (5).
Calibration weight: 5,000 g; accuracy: + 0.075 g.
After connection to AC power and before each
calibration/adjustment, allow the scale to warm up
for approx. 30 min.
Hold down the Ukey (5) for 2 sec.
When 5000 is displayed, release the key.
Center the calibration weight on the weighing pan
(11).
Calibration/adjustment is performed automatically.
After calibration and adjustment, remove the weight.

Menu Settings
Navigating the SETUP Menu
Example:
Menu Item: Adaptation to ambient conditions
§Hold down the Lkey [ENTER] for approx. 2 sec.
“SETUP” will appear on the display (Level 1).
§ Use the RS keys to select the desired menu item
in the first level.
§Press the Lkey [ENTER] to select the second level
(Level 2).
§Use the RS keys to select the desired menu item
in the second level, here “SCALE.”
§Press the Lkey [ENTER] to select the third level
(Level 3).
§The menu items in the third level (Level 3) will be
displayed. Use the RS keys to select the desired
menu item, here “Ambient Conditions.”
§Press the Lkey [ENTER] to select the fourth level
(Level 4).
§Call up the menu item desired in the fourth level.
Use the RS keys to select the desired menu item,
here “STABLE.”
§Press the Lkey [ENTER], “o” will appear; the
desired setting is defined.
(We have come to the end of our example.)
§Press the ckey (Clear) several times to exit the
menu.
Note:
To obtain a detailed list of the menu codes, please
ask your nearest Sartorius office!
Please note that English screens are available for the
scale even if they are shown in German.
16
Setup
Input
Info
Language
Setup
Scale
Application
Interface
SBI Settings
SBI Print
Extras
Setup-Scale
Ambient Conditions
Filter
Stability
AutoZero
Units
Decimals
Setup-Scale-Ambient Conditions
Very Stable
o Stable
Unstab.
Very Unstabl.

17
Important Menu Settings
§Hold down the Lkey [ENTER] for approx. 2 sec. “SETUP” will appear on the display (Level 1).
Level 1
SETUP
Language Settings
Level 1 Level 2 Level 3 Level 4
LANGUAGE §Press the Rkey to select “LANGUAGE”
§Press the Lkey [ENTER]
oGERMAN §Press the RS keys to select a language
ENGLISH §Press the Lkey [ENTER]: “o” will appear;
FRENCH the desired setting is defined.
ITALIAN §Press the ckey (Clear) several times to
etc. exit the menu.
Standard Basic Setting (0.1g)/PolyRange (0.05g/0.1g) and grams/PT./LB.
When you turn on the scale, the active basic setting is found under:
“SETUP- SCALE – UNIT” and “SETUP- SCALE – DECIMALS”:
Level 1 Level 2 Level 3 Level 4
SETUP §Press the Lkey [ENTER]
SCALE §Press the Lkey [ENTER]
UNIT §Press the RS keys to select
“DECIMALS”
GRAMS §Press the Lkey [ENTER]
oPT./LB. §Press the RS keys to select
“STANDARD”
DECIMALS §Press the Lkey [ENTER], “o” appears,
o STANDARD the desired setting is defined.
POLYRANGE §Press the ckey (Clear) several times to
exit the menu.
Activating the IToggle Key; Configuring (Basic Setting)
After the toggle key, I, has been activated, you can individually configure it with either 1 or 2 decimal
places, as well as with grams or PT./LB. You can then toggle between the unit and the decimal places.
Level 1 Level 2 Level 3 Level 4
SETUP §Press the Lkey [ENTER]
APPLICATION §Press the RS keys to select
“APPLICATION”
§Press the Lkey [ENTER]
TOGGLE §Press the RS keys to select “TOGGLE”.
OFF §Press the Lkey [ENTER]
o ON §Press the RS keys to select “ON”.
§Press the Lkey [ENTER]; “o” appears,
the desired setting is defined.
§Press the ckey (Clear) several times to
exit the menu.

Assigning the IToggle Key (6)
By pressing the toggle key I(6), the scale toggles between the basic setting (see page 14) and the
settings defined under “SETUP- APPLICATION – UNIT” and “SETUP- APPLICATION – DECIMALS”
Level 1 Level 2 Level 3 Level 4
SETUP §Press the Lkey [ENTER]
APPLICATION §Press the RS keys to select
“APPLICATION”
UNIT §Lkey [ENTER], select the Skey “UNIT,”
press Lkey [ENTER].
PT./LB. § Press the RS keys to select “GRAMS”
o GRAMS §Press the Lkey [ENTER], “o” appears;
the desired setting is defined
§Press the ckey (Clear)
DECIMALS §Press the RS keys to select
“DECIMALS”
STANDARD §Press the Lkey; select setting
o POLYRANGE §Press the Lkey [ENTER]; “o” appears,
Press the ckey (Clear) to exit the menu.
Activating the “LOCK” Function “ ”
By activating the “LOCK” function, you can protect the scale from unauthorized use. When the scale
is connected to a PC, the two devices are in constant communication. If the “LOCK” function is
activated under “EXTRAS,” and data transmission to the PC is interrupted, the lock symbol will be
displayed. The scale will automatically be locked, preventing other weighing operations.
Level 1 Level 2 Level 3 Level 4
SETUP §Press the Lkey [ENTER]
EXTRAS §Press the RS keys to select “EXTRAS”
§Press the Lkey [ENTER]
LOCK §Press the RS keys to select “LOCK”
§Press the Lkey [ENTER]
OFF §Select “ON” using the RS keys
o ON Confirm with the Lkey
§Press the ckey (Clear) several times
to exit the menu.
Entering a Password
In addition to activating the “LOCK” function, the user may also enter a password.
Should the user wish to deactivate the “LOCK” function by pressing the “OFF” key, the user must first
enter the valid password. The password is comprised of a 6-character numeric code.
Use the RS keys to call up numbers (0 to 9).
Six dashes (------) will appear in the display (10). The first dash will “blink” in the display z.
Select a number (0 to 9) using the RS keys; press the Lkey [ENTER] to save the number.
The second dash will start to “blink.” Repeat the aforementioned process. Should you wish to assign
a “blank space” to one of the six characters, simply press the Lkey [ENTER] when the dash begins
to blink. Once you have entered all six characters, simply press the Lkey [ENTER] when the cursor
flashes in order to save the code.
18

19
Note:
Keep the numeric code in a safe place!
The scale can only be accessed by entering the correct code!
Level 1 Level 2 Level 3 Level 4
INPUT §Press the RS keys to select “INPUT”
PASSWORD §Press the Lkey [ENTER]
§Press the Lkey [ENTER]
PW..NEW §Press the RS keys to select “PW.NEW”
z §Enter the numeric code; press the Lkey
[ENTER].
§Press the ckey (Clear) several times
to exit the menu
Changing the Password
Should you wish to change the password, you must first correctly enter the old password under
“Password.” “PW.OLD” will be displayed. Following the correct input, “PW.NEW” will automatically
appear. You can now enter a new password, or confirm each blinking dash by pressing the Lkey
[ENTER]. Blank spaces are then displayed.
Note:
The old password can be deleted by entering 6 blank spaces. The scale is thus reset to its original
state; i.e., the scale is not password-protected.
Level 1 Level 2 Level 3 Level 4
INPUT §Press the RS keys to select “INPUT”
PASSWORD §Press the Lkey [ENTER]
PW.OLD §Press the Lkey [ENTER]
z§Enter the old password “PW.OLD”
PW.NEW §“PW.NEW” will appear when the old
password is correctly entered
z§Enter the numeric code; press the Lkey
[ENTER]
§Press the ckey (Clear) to reset the menu

Resetting the Scale: “RESET”
If necessary, you can reset the scale to factory settings.
Note:
If a password was activated, the correct password must first be entered.
Level 1 Level 2 Level 3 Level 4
SETUP §Press the Lkey [ENTER]
RESET §Press the RS keys to select “RESET”
§Press the Lkey [ENTER]
MENU §Press the RS keys to select “MENU”
§Press the Lkey [ENTER]
YES §Use the RS keys to select “YES”
o NO §Press the Lkey [ENTER]; “o” will appear:
The factory settings are restored .
“Menu” appears on the display.
§Press the ckey (Clear) several times
to exit the menu
Setting Codes
Under the setting “CODES,” the menu items are displayed in code 1.1.1.1.
Level 1 Level 2 Level 3 Level 4
LANGUAGE §Press the Rkey to select “LANGUAGE”
§Press the Lkey [ENTER]
GERMAN §Press the RS keys to select “CODES”
etc. §Press the Lkey [ENTER]; “o” will appear:
the new code is set
o CODES §Press the ckey (Clear) several times
to exit the menu
Selecting an Interface (PMA7501-X00GL, only)
You must configure an additional menu item in the PMA7501-X00GL Setup to select an interface.
!You may only activate one data interface!
“SETUP-INTERFACE-CONNECT”
Level 1 Level 2 Level 3 Level 4
SETUP §Press the Lkey [ENTER]
interface §Press the [ENTER] key
§Press the RS keys to select “CONNECT”
anschluss §Press the Lkey [ENTER]
ETHERNET §Press the RS keys to select the inter-
face desired.
o RS232 EXT. §Press the Lkey [ENTER], “o” will appear,
indicating that the desired interface
RS232 inT. is activated
§Press the ckey (Clear) several times
to exit the menu
Note:
To obtain a detailed list of the menu codes, please ask your nearest Sartorius office.
20