Satel AMD-101 User manual

®
WIRELESS MAGNETIC DETECTOR
AMD-101
amd101_e 09/05
The AMD-101 wireless magnetic detector is designed for operation as part of the
ABAX two-way wireless system.
The AMD-101 detector is of the NC type, i.e. moving the magnet away from the reed
relay opens the electric circuit, which is recognized as violation of the detector.
Descriptions of Figure 1:
1 – additional input terminals - The NC type detector can be
connected to them. The signal from the additional input
is passed independently, the AMD-101 detector is
included twice in the list of wireless devices in the
system.
2 – tamper contact – It reacts to opening or pull-off of the
housing from the wall.
3 – CR123A lithium battery (voltage: 3V), which ensures
approx. two years’ operation.
4 – reed switch 1.
5 – reed switch 2.
6 – pins which enables to choose the active reed switch.
7 – LED indicator – is on in the TEST MODE only (see the ACU-100 controller manual)
to signal communication with the controller and violation (of the detector or
tamper contact).
Placed on the electronics board is a label with 7-digit serial number, which must be
indicated when registering the detector in the system.
1. DETECTOR INSTALLATION
Prior to permanent mounting of the detector, you should check the level of
signal received from the detector by the ACU-100 controller and, if necessary,
change place of the installation so as to ensure optimal positioning in terms of
communication.
Place the battery inside the detector immediately before registering the detector
in the controller. If not registered or lacking communication with the controller,
the detector consumes more energy, which reduces the battery lifetime.
Be particularly careful when installing or replacing the battery, so as not to
damage the reed switches on the electronics board.
Fig. 1. View of the
detector PCB. Fig. 2. The way of putting jumper on pins.
active reed switch 2active reed switch 1

SATEL AMD-101
2
The cable connecting the additional detector with the onboard terminals may not be
longer than 3m. If the additional input is unused, its contacts should be shorted.
For information on registration and installation of the detector in the wireless system -
see the ACU-100 controller user manual.
Fig. 3. View of AMD-101 in the housing with indicated position of
reed switches.
Fig. 4. Examples of mounting reed switch and magnet, showing the maximum ranges
(top view). The indicated ranges apply to the magnet situated at the height of
AMD-101 PCB.
Side view
Top view
tamper contact spring
reed switches
reed switches
110mm
17mm
27mm
26mm
20mm
24mm
15mm
15mm
magnet
magnet
reed switch reed switch
20mm
magnet
reed switch

AMD-101 ABAX 3
2. TECHNICAL DATA
Detector type ..............................................................................................................NC
Operating frequency band..........................................................868.0MHz ÷ 868.6MHz
Additional input sensitivity .................................................................................... 312ms
Power supply.........................................................................lithium battery CR123A 3V
Lifetime of detector power battery.......................................................... approx. 2 years
Operating temperature range.......................................................................0°C...+55°C
Dimensions of reed relay housing........................................................... 24x110x27mm
Batteries in the battery-supplied wireless equipment should be replaced by
qualified personnel. Incorrect replacement of the battery can pose an explosion
hazard.
Always use the CR123A 3V lithium batteries.
The used batteries must not be discarded, but should be disposed of in
accordance with the existing rules for environment protection.
DECLARATION OF CONFORMITY
Product:
AMD-101 - Wireless Magnetic Detector for
ABAX System
Manufacturer: SATEL spółka z o.o.
ul. Schuberta 79
80-172 Gdańsk, POLAND
tel. [phone]
fax. [phone]
Product description:Wireless magnetic detector with an additional input, designed for interaction
with elements of the ABAX wireless system, operating in the 868.0MHz – 868.6MHz frequency
band, supplied from a 3V lithium cell. The device is intended to be used in burglary and panic alarm
systems.
This product conforms to the following EU Directives:
R&TTE 1999/5/EC
This product meets requirements of the harmonized standards:
R&TTE: ETSI EN 300 220-1: v.1.3.1; ETSI EN 300 220-3: v.1.1.1;
EMC: ETSI EN 301 489-1: v.1.5.1.; EN 301 489-3: v.1.4.1
Safety: EN60950-1:2001
Notified body taking part in conformity evaluation:
Identification No.: 1471
Gdańsk, Poland 2005-07-15 Head of Test Laboratory:
MichałKonarski
The latest EC declaration of conformity and product approval certificates are available for
downloading on website www.satel.pl

SATEL AMD-101
4
SATEL sp. z o.o.
ul. Schuberta 79
80-172 Gdańsk
POLAND
tel. + 48 58 320 94 00
[email protected]
www.satel.pl