saunalife Sconce Plus User manual

Sconce + Led Lightbar
@saunalife
Sconce Plus
Installation Manual

2
LED Lightbar Package Contents:
Sconce Light
(qty. 2)
2-Pin 30’ Cable
(qty. 3)
Adjustable Mounting Clips
(qty. 3)
Stationary Mounting Clips
(qty. 3)
White Led Light Bar
(qty. 1)
Mounting Template
(qty. 2)

3
Installation Recommendations
Please read this manual in its entirety prior to installation
and keep it in a safe place after for future reference.
The RF Driver and Power Supply may be installed outdoors but must be
protected from rain and snow. RF Driver and Power Supply should be installed
in a waterproof electrical enclosure.
When installing the RF Driver and Power Supply inside the sauna, maintain a
minimum distance of 20” from heat source and a maximum height of 20” off
floor or in fan's path.
If installed inside the sauna, the RF Control must not exceed 131°F. Control
should be no more than 3' off the floor and away from heater. Test
temperature reading of location before mounting.
Consider light placement carefully. Each fixture should be placed to avoid
direct contact with the bathers eyes.
LED Light Bar max operating temperature is 195°F, installing LED light bar in
location where temperature will exceed 195°F may cause light failure
Electrical Requirements
•A 120V AC electrical outlet is needed to power the lighng
system.
•Your electrician will determine the type of electrical outlet,
box, and piping to be used.
•All wiring must be done in accordance with naonal elec-
tric code and local building codes by a cered electrician.
•Improper voltage or connecons will damage the compo-
nents and void warranty.
IMPORTANT
IMPORTANT
IMPORTANT
IMPORTANT
IMPOR
TANT

4
Specicaons:
PART
NUMBER
Operating
Voltage
(VDC)
Max Wattage Lumens Dimensions
BP031071
LED White 24V DC 6.4W 703 15-3/4" x 12-1/4" x 3-1/4"
Sconce Light Specifications
Kelvin: 3500k Operating Temp:
-13°F to 195°F IP Rating: IP67 Certication: CE / FCC
PART
NUMBER
Operating
Voltage
(VDC)
Max Watt-
age Lumens
Dimensions
(with flush
clips)
Dimensions
(with adjusta-
ble clips)
E6
BP031085
LED White
24V DC 11.32W1,246 3/4W x 9/16H x
48L
3/4W x 1-1/4H
x 48L
Led Light Bar Specifications
Kelvin: 3500k Operating Temp:
-13°F to 195°F IP Rating: IP67 Certication: CE / FCC
Required Tools:
Cordless
Drill
3/4 Wood
Drill Bit
(Installaon
Dependent)
Level
E7
BP031086
LED White
24V DC 14.27W 1,571 3/4W x 9/16H x
60L
3/4W x 1-1/4H
x 60L
E8
BP031158
LED White
24V DC 18.69W2,059 3/4W x 9/16H x
76L
3/4W x 1-1/4H
x 76L

5
STEP 1.
Installation of Sconce Lights
Locate provided mounting template and mount at light location to locate
mounting screw locations and light cable access. Recommended light
installation height 5ft from base and 16in from side wall.
Repeat this step for second light.
STEP 2.
Run Light Cable
Running the light cable will be dependent on your installation. Cable can be
routed outside to driver location or through the barrel. If going through the
barrel use a 3/4” drill bit for cable to pass-through.
Repeat this step for second light

6
STEP 3.
Install Mounting Brackets & LED Light Bar
Determine the location where LED light bar will be installed. Screw Mount-
ing Clips to surface ensuring even coverage of light xture. Carefully snap
LED light bar into each clip.
STEP 4.
Connect 2-Pin 30’ Cable to Light Bar
Connect the light cable end to lead of the light bar. At Driver, connect to one
of the 4 leads on the 2-Pin 4-Way cable

9
STEP 5.
Install Power Supply
Connect AC power cord cable to power supply block. Place power supply
near RF driver. Connect DC cable end from power supply and connect into
RF driver DC IN port.

7
On IOS or Android down-
load the Tuya Smart App
Step 1 Step 2 Step 3 Step 4
Step 5 Step 6 Step 7
Wi-Fi Setup
Step 9
To set up Wi-Fi operation follow the steps
below
Note: Wi-Fi Driver supports 802.11 b / g / n
2.4 GHz Wi-Fi standard. The Wi-Fi Driver
Device added success-
fully, press done to
complete setup
Select your
Wi-Fi network
Press Add next to
Discovering
Devices
Main screen
press Add Device
Open Tuya app
and press Sign
Up to create
an account
Enter an email
address to regis-
ter an account
Check email and
enter vericaon
code
Create a
password

8
No Power
•Verify that the electrical outlet has voltage.
•Check that connections on the Power Supply are secure.
•Check that the DC barrel plug on the Power Supply is securely connected.
Power but light's not turning on
•Check that the Pigtail cable from the Driver is securely connected and that
wiring is correct.
•Check that 4-way light cable is secure and connected.
•Check that all 30’ cables to lights are securely connected.
•Verify each light functions by testing them directly to the Driver independently.
Note: To test individual light, disconnect 4-way light cable and connect 30’ cable
directly to Pigtail lead off Driver, or connect light directly to Pigtail.
•Verify that RF Remote is paired with Driver.
Lights on but no function from Control
•Verify battery is inserted correctly.
•Low battery, replace with new battery.
•Check that DC power cable from Driver to Control is securely connected.
•Ensure that the distance from the Remote to the Driver is not more than 98
feet. If so, relocate Driver closer to room.
Replacement Parts
Description Part Number
Sconce Light BP031071
48” White Light Bar BP031085
Troubleshooting
60” White Light Bar BP031086
2-PIN IP67 30' Cable BP031077
76” White Light Bar BP031158

9
Notes:

10
Page Intentionally Left Blank

© 2023 Bathing Brands, Inc. REV: 07/2023