saunalife X7 User manual

Model X7 Sauna Room
Installation Manual

Floor Raiser 1
2
Floor Raiser 2
2
Support Rail 1
4
Support Rail 2
4
Back Wall 1
1

Back Wall 2 1
Back Wall 3 1
Side Wall 1 2
Side Wall 2 1
Side Wall 3 1
Window Element 2

Door Element 1
Roof 1 1
Roof 2 1
Roof 3 1
Bench 1
Side Bench
1

Backrest 1
Lower Backrest 1
Bench Support 2
Side Bench Support 1 1
Side Bench Support 2 1
Cornice Board 1 1
Cornice Board 2 2

Heater Cover 1
Front Wall Cover Slat
2
Vent Cover 1
Door Handle 1
Footrest 1
Screws QTY
4.5 x 80mm (.19" x 3.14") 8
4.5 x 70mm (.17" x 2.75") 44
4 x 60mm (.15" x 2.36") 8
4 x 50mm (.15" x 1.96") 48
3.5 x 40mm (.13" x 1.57") 26
[PP[ 16
Vent Cover Washer 1
Tenon 8

Floor Raiser 1
Floor Raiser 1
Floor Raiser 2
Floor Raiser 2
Screws
4.5x80
Tenon
Support Rail 1
Support Rail 1
Support Rail 2
Support Rail 2
Support Rail 1
Screws
3.5x20
Step 2. Connect Wall Support Rails
Each wall support has a pre-drilled hole for a Tenon.
Insert the tenons in the longer support rail holes.
Fasten the wall support rails together and connect
from corners using four 3.5x20 screws per corner.
Step 1. Connect the Four Floor Risers
Fasten the four Floor Risers together using 4.5x80 screws,
being sure the two shorter boards are located on the
sides and the two longer boards are on the front and back.
Use a framing square to ensure the assembly is square.
Pre-drill holes for
the screws

Screws
4x50
Back Wall 1 Side Wall 1
Screws
4.5x70
Vent Holes
On Top!
Step 3. Position Wall Support Rails
Lay the wall support rail assembly squarely on top
of the floor risers with the groove facing up.
The rails should overlap both sides of the riser by approximately 0.5”.
Secure the assembly to the floor risers using four 4x50 screws evenly
spaced on each wall support rail
Step 4. Position Wall Sections (Back Wall 1 & Side
Wall1)
Position Back Wall Section 1 in the groove of the back rail and push
it flush against the left rail. Have a helper hold back wall section.
Orient Side Wall Section 1 and place it in the groove of the left rail.
Push the flat edge flush against back wall section. Align the two
panels so they are flush and fasten them using 4.5x70 screws
Pre-drill holes for
the screws

Back Wall 3
Back Wall 2
Side Wall 1
Screws
4.5x70
Side Wall 2
Window
Door Element
Screws
4.5x70
Step 5. Position Back Wall Sections 2 & 3, and Side Wall 1
Position Back Wall 2 section into the groove of the back rail.
Attach it to Back Wall section 1 by way of the tongue and groove fit.
Secure it by tapping it into place with a rubber mallet.
Repeat this step for Wall Section 3, again tapping it into
place with a rubber mallet.
Position Side Wall Section 1 into the groove to the
right side rail and push flush against the back wall.
Be sure panels are flush with each other. Fasten them
using 4.5x70 screws.
Pre-drill holes for
the screws
Step 6. Position Side Wall Section 2, Window Section
& Door Section
Position Side Wall Section 2 into the groove of the side rail. Slide Side Wall Section 2 into
place with side wall section1. Section 2 connects
to Section 1 via tongue and groove
so there is no
need to use screws. Use a rubber mallet to
secure the fit.
Place Window Section in the
groove on the front rail and push against side rail.
Be sure the two sections are flush and fasten
them using 4.5x70 screws.
Place Door Section onto the front rail orienting it
so that the door opens according to your
preference. Door Section connects to Window
Section via tongue and groove so there is no
need for screws. Gently tap it into place
with a rubber mallet to secure the fit.

Window
Roof Support
Rail
Side Wall 3
Screws
4.5x70
Screws
4x50
Step 7. Position Side Wall Section 3 and
Window Section
Position Side Wall Section 3 into the groove of the side rail so that
the heater vent holes are located at the bottom. Slide wall section into
place with Side Wall Section 1. Side Wall 3 connects to Side Wall 1 via
tongue and groove so there is no need to use screws.
Use a rubber mallet to secure the fit.
Next, place the Window Section into the groove
of the front rail and connect it to the Door Section
via the tongue and groove fit. Gently tap into
place with a rubber mallet to secure the fit.
Now, making sure Window Section and Side Wall 3
are flush with each other, secure them with
4.5x70 screws.
Pre-drill holes for
the screws
Step 8. Assemble and Position Roof Support Rails
Reference step 2 and connect Roof Support Rails in the same way.
Place the assembly on top of the wall sections so that the wall
sections fit snugly into the groove. When in place, secure to the
assembly to the walls using four 4x50 screws on each rail.

Bench
Support
Screws
4.5x70
Screws
4.5x70
30.75"
Step 9. Bench Installation
Use 4.5x70 screws to connect the Bench Supports to the wall. Make sure the supports
in both walls are in same height. When the supports are assembled place the bench on
the supports. Use three 4.5x70 screws to connect the seat bench to the back wall.

Side Bench
Support 1
Screws
4.5x70
Side Bench
Support 2
Screws
4x60
16.1"
Screws
4.5x70
Step 10. Side Bench Installation
Attach the Side Bench Support 1 to the back wall using
two 4.5x70 screws. Side Bench Support 2 connects to
the Window Section using 4x60 screws. Place the side
bench on the supports and fasten wit three 4.5x70
screws to the side wall element.
Pre-drill holes for
the screws

Backrest
Screws
4x60
Lower Backrest
Screws
4x60
Step 11. Backrest and Lower Backrest Installation
Center the Backrest between the two sides and position it vertically at a height most
comfortable for you (typically 8-12” from the bench).
Using a level to ensure proper installation, fasten the Backrest into place using 4x60
screws. Using a level, secure the Lower Backrest to side wall section with 4x60
screws at the same height above the upper long bench.
Pre-drill holes for
the screws.

Roof 1
Roof 2 Roof 3
Screws
4x50
Cornice
Board 1
Cornice
Board 2
Cornice
Board 2
Screws
3.5x40
Step 12. Position Roof Sections
Place the Roof Panels on top of the ceiling supports.
Connect the sections via the tongue and groove fit.
From the backside, roof panels must be in the same
line with ceiling supports. Position the both sides
equally 1.875". Connect panels with 4x50 screws.
Pre-drill holes for
the screws
Step 13. Cornice Boards
Connect the Cornice Boards to the roof, using 3.5x40 screws.

CoverCover
Slat
Screws
3.5x40
4x60
Screws
4x60
Step 14. Cover Slats to the Front Wall
Connect the Cover Slats using 3.5x40 screws
Step 15. Heater Cover
Connect the Heater Cover to the wall with 4x60
screws. Perform this step after the heater is installed.
Note: Follow heater manufacturer recommended
installation for heater guard.
Pre-drill holes for
the screws
Step 16. Vent Cover & Door Handle
Connect the Vent Cover with 3.5x40 screw.
Between wall and Vent Cover add small washer.

Footrest
20"
Floorplan View
Screws
4.5x70
Step 17 Footrest Installation
Connect the Footrest with 4.5x70 screws from one side to the
Side Bench and from the other side to the side wall. Two
screws per side. Measure from front wall must be 22.14"
REV: X703923